When renovating water and electricity, should you make a groove in the wall and floor?

It is definitely needed, so that you can save a lot of space, and you will not have a lot of fruit in your home. It's a smart choice.

Personally, I think don't slot, slotting is easy to affect the flatness of the ground, will have a certain impact on the back decoration, increase the cost of decoration, if you groove on the load-bearing wall, it is easy to affect the safety of the building.

Need. It can have a good practice, and in life, it can also make the home look cleaner, and there will not be a lot of lines. There will also be a lot of processes.

The first step of hydropower transformation is hydropower positioning, that is, according to your needs to determine the location of the whole house switch socket and the location of the waterway interface, the plumber should draw out the direction of the water pipe and wire on the wall according to the position of the switch socket water faucet, that is, the layout of the line, remember to ask your decoration team for the hydropower diagram, let the plumber according to the map to explain the line to you clearly, don't be afraid of trouble, the plumber will definitely meet your requirements, after the completion of the hydropower renovation if you do not sign, the plumber does not want to take money from the decoration captain. <>

After the hydropower positioning, the next step is to groove. The groove made by a good groove beater is basically a straight line, and there are basically no hairy teeth on the edge of the groove. Note that before slotting, be sure to ask the plumber to mark all the hydropower directions on the wall, and remember to check the hydropower diagram to see if it is consistent.

There are a few more points to note about hydropower transformation:

1. It is best to indicate the brand of the wire used in the circuit transformation in the contract.

2. The switch of the whole house should be basically in the same horizontal position. <>

3. The sockets of the whole house should be at the same level as much as possible, and special sockets such as air conditioners, refrigerators and special requirements are exceptional.

4, the circuit transformation in the phase line, the color of the zero line should be the same for each house, if possible, it is best to indicate the color of the live line, the zero line and the control line in the contract, and the protection line is yellow and green according to the national regulations.

5. It is best to use 3-wire multi-strand for socket lines (including air conditioners and refrigerators), and 2-wire multi-strands for lighting wires.

6. The bottom box is buried, if you can, it is best to buy the bottom box yourself, please report the installation fee to the decoration team.

7. Regarding the audio cable, if you are not a professional audiophile, it is best not to install the audio cable: the housing area in Shenzhen is basically about 100 square meters, and the area of the living room is generally not very large. The air traffic control is also counted as silver.

Regarding the renovation of the waterway, there is one point that I think it is necessary to say: Regarding the issue of hot water, in terms of the weather in Shenzhen, does it need to use hot water in the washbasin and the vegetable sink in the kitchen? If you need hot water, turn on the water heater and connect it.

When decorating, I only sighed that it is not easy to make money, but it is so easy to spend money!

Finally, it is best to note in the contract that you must wait for the completion of the hydropower renovation carpenter the site, the benefits of this: you don't have to pay attention to two things at the same time, hydropower renovation is a very important expenditure in the decoration, but also the bulk of the decoration company's profits, and the hydropower renovation is very hidden, if the carpenter enters the construction at the same time, it will distract your attention and will not pay attention to the hydropower transformation.

When renovating the waterway, pay attention to the cleanliness of the perimeter. When concluding a contract for waterway renovation, it is advisable to indicate the materials used in the waterway renovation. In addition, in the renovation of the waterway, it is necessary to pay attention to the size of the sewer pipe in the original room, and the pipe connected to the original sewer pipe in the house should be matched with the original sewer pipe.

In the circuit transformation, it should be noted that the lamps and lanterns of the whole house should be installed in advance in order to determine the location of the switch socket, and at the same time, it should be noted that the new buried wire and the replacement wire are different. When buying a doorbell, it is better to buy a wireless doorbell.

Yes, it must be slotted, so that the concealment is better, and the effect will not be ugly, the specific operation is to make the corresponding groove in the wall, and then put the water and electricity wires in it for combined connection.

Of course, it is necessary to groove, because many lines need to be installed in the wall, which needs to be grooved according to the horizontal reference line, and can not be slotted indiscriminately, otherwise it will lead to damage to the wall.

It has to be grooved. First, use a cutting machine to cut out the gaps in the wall, then stuff the wires into the PVC pipe, then put the PVC pipe in the gap, and then lay a layer of mesh, and then repair the wall.

No, you don't. When carrying out water and electricity renovation, do not groove the ground and wall, which will affect the aesthetics of the decoration.

I felt that I needed to make a slot in the wall and floor. If you don't groove, it will be very troublesome when you renovate the water and electricity, and it will also hurt the wall.

Yes, it is needed, you can put a lot of things, and it will also play a safe protective effect, so you need to go to the slot.

With the development of society, the living conditions are getting better and better, and now there are more and more people buying houses, so they now attach great importance to decoration, especially when we change to hydropower, we must first draw the route, and then slot, and slotting also requires a certain technology, first of all, we must also pay attention to the strength and angle of slotting, so that it will not affect the appearance, when we clean up the tide, it is also necessary to clean up the inside of the slot. Don't get any debris in.

Hydropower transformation with toothless saw slotting, need to draw the line first, according to the plan to be changed to draw the line, the line adopts the horizontal and vertical method of planning.

1. Toothless saw slotting, slotting with a toothless saw according to the line, and cutting out the line on the wall.

2. Add water, and then add some water to the slotted wall, and add water all the way during the cutting process to prevent the blade from overheating.

3. Punch the groove, use an electric hammer to punch the cut wall out of the groove, pay attention to the strength and angle, and try to punch as neatly. Clean the groove, clean the groove that is flushed out, and knock down the places that are easy to fall. Waterproof, if it is a pipe in the toilet, it is recommended to brush some waterproof (or not, depending on personal wishes).

Comparison of the lower line pipe. Put the tube that needs to be lowered into the trench for experimentation, and if there is no problem, the trench will be done.

For the slotting of hydropower, we also have to pay more attention, because this is also very important for the comfort of life in the future, if you do not draw a good route, go to the slotting to decorate this hydropower, there may be a lot of inconvenience in the future life, if you want to redecorate, it is also more troublesome, so we still need to plan it when we do this.

When we are doing hydropower slotting, if we encounter a turn, it is best to make it arc-shaped, which is also convenient for future maintenance and easier to pump the wire, and the arc is not easy to hurt the wire, so this is very good.

Not all walls are suitable for slotting, such as load-bearing walls, some workers will ignore the brutal slotting, resulting in the destruction of the building structure, and the ground slotting should also be careful not to damage the floor slab. The correct slotting must be horizontal and vertical, the pipe of the flat walking line is 60-90cm high from the ground, and the place where there is a faucet must be vertical. The socket is slotted 40 cm from the ground, the hanging air conditioning socket is slotted from the ground, and the switch is slotted from the ground.

In addition, there is a principle in hydropower construction, "go to the wall and not the ground, and go to the top and not the wall". It means that the line is best to go to the top, the top can not go, consider walking the wall, the wall can not go, and finally go to the ground. Because the top line is in the ceiling, it is easy to maintain, but it is different to go to the ground, and the cost is too great to lift the floor.

It can be used, the cutting machine is slotted, it is very convenient, and the damage to the wall is not very large.

In order to avoid convenient maintenance in the later stage, and in order to reduce costs, you can go to the ground, do not go to the top, and be sure to pay attention to the depth.

At this time, we should ask a professional master to open a groove for us, and we should also pay attention to the instructions of the professional master, don't do what you want, and regret it in the future.

As an indispensable part of home decoration, there are many places that need to be paid attention to in the decoration process. In the process of hydropower renovation, before laying the hydropower pipeline, the decorator will play the line on the wall and the ground, and then dig the pipe groove with a cutting machine and chisel according to the hydropower point, and finally lay the hydropower pipeline in the pipe groove. The ground is grooved, and the water and electricity lines are buried in the trenches.

In the subsequent renovation, the workers are not easy to collide with the pipe and cause damage; The water and electricity pipelines are not on the ground and will not affect the floor height of the house; When laying floor tiles, cement mortar can better cover the water and electricity pipes, and the ground is easier to level.

The wall is slotted, and the water and electricity pipelines are buried in the trough, which does not affect the thickness of the wall. It is convenient for subsequent wall decoration construction such as putty and latex paint to avoid wall cracking. You should know that pipes are fixed with pipe clamps when they are laid.

In fact, the quality of the water and electricity pipes is not bad. As long as it meets the construction specifications, it will not be easily damaged. Even if the ground is not slotted, it will not have any effect on the laying of water and electricity pipes.

Leveling the ground itself loses some height, and the size of the plumbing pipes is not large. When laying tiles, the thickness of the cement mortar is enough to completely cover the water and electricity pipes, so even if the ground is not grooved, it will not have any effect on the subsequent renovation. According to the needs of our home, identify the water and electricity points on the wall and mark the wall.

Then, according to the wiring direction of the waterway layout at home, pop the slotted line to the wall. This is usually the two lines that pop up, the slot edge line. These two lines are the control lines slotted underneath.

When grooving, a cutter is usually used to cut both sides in a straight line first. The cutting depth is generally 20 mm to 30 mm. The exact depth is determined according to our pipe layout.

The principle is that there should be a protective layer of about 20 mm on the surface of the catheter we arrange to determine the depth of slotting. Use a cutter to make the cut, and then you can use an electric pickaxe to remove it and chisel it to the depth we need. In addition, we can also use a special slotting machine to make slots directly, and we can directly open the slots we need.

Wire pipes and water pipes are installed in trenches and are securely fastened with fixing clips or steel nails and copper wires.

I don't need this kind of decoration, I feel really bad, it will make the home very unsightly, and it will look like there will be a lot of shortcomings. Covert retrofitting should be chosen.

If needed, a slot can be used to make some pipes better, which can make the home have a very aesthetically pleasing effect, without some exposed pipes.

I felt that I needed to make a groove in the wall and floor, as it would help with the remodeling. It can also carry out more reasonable hydropower transformation applications.

Yes, this can hide all these lines, it will have a good effect, and it will make the home decoration look very neat.