How to change the waist of the pants to be bigger, how to change the waist of the pants to be smalle

Take a rubber band and use the band to put the buttons and buttonholes together.

The specific steps are as follows:

Method 1: 1. Unbutton the button: Unbutton the middle of the pants and take a rubber band.

2. Thread the rubber band through the buttonhole: Put your rubber band on top of the button first, and then pass the rubber band through the buttonhole.

3. Put the rubber band on the button again: after passing through, fold the rubber band back and put it on the button again.

Method 2: 1. Find the middle position of the pants: find the middle part behind the waist of the pants and cut this position with scissors.

2. Thread the needle and thread: Thread your needle and thread and thread the needle from the bottom to the top through the edge of the cut pants.

3. Repeat the steps: After wearing out, go around the hem of the pants, and then wear it from the bottom to the top, and repeat the steps until all the positions are sewn.

Here's how:Tools: scissors and needle and thread.

1. First turn the pants to the back and use scissors to cut the waistband of the pants at the back. 2. Seal the cut place with a needle and thread, and finally lock the edge, and you're done.

Rubber band: The way to not change the size is to find a way to button the pants, you can use a rubber band to circle the buttons of the pants, and then put the rubber band into the hole on the other side of the pants, wait until the rubber band passes through this eye, then pull it back, and then buckle it to the button.

Here's how to change the waistband of the pants from smaller to largerTools Raw materials: blades, needles and threads, scissors.

1. First remove the strap in the middle of the back of the pants with a knife.

2. After taking it off, cut a small triangle with scissors in the middle position.

3. Then use a needle and thread to sew the small triangle edge.

4. This is how it looks when sewn up.

5. Finally, sew the small strap that was removed before on it to make it a beautiful and complete triangle. In this way, the waistband of the pants becomes larger.

Let's take a look at the way to change the waist of the pants! A clever way to change the waistband of your trousers.

Start by finding the center line on both sides of the pants and prepare the needle and thread.

Then, the first stitch is poked from the inside to the outside on either side of the middle line of the pants.

<> then the second needle is on the other side of the middle line of the pants, poking the needle from the outside to the inside and then from the inside to the outside.

After <>, the third needle is poked a little inside a little below the first needle, from the outside to the inside, and then from the inside to the outside. The fourth needle is returned to the inner part of the second needle, from the outside to the inside, and then the first needle is poked from the inside out. Repeat the above operation, and the sewing will be in a trapezoidal shape.

<> Finally, the finishing needle needs to be poked from the inside along the middle line of the pants from the outside to the inside. This is a matter of pulling the stitches harder, and the stitches that were sewn just now will be hidden, and the waistband of the trousers will be smaller.

What should you do if the waistband is small when you buy pants, and you want to make the waistband bigger, let's explain the trick of changing the waistband of the pants to a bigger one. <>

Method 1

Chalk down your small position. It is a symmetry that should be drawn on the left and right sides of the pants to avoid asymmetry after the pants are sewn. After the drawing, sew it in the inside of the pants until ** you decide for yourself.

It should be sewn tightly, and it should be sewn until it feels like the thread will not break. Once sewn, you can cut off the excess. To determine how much to change, if you change more, remove the waistband of the pants first.

Fold the trousers a little more, and then sew the waistband. If not much, fold it out at the approximate position of the trouser pocket.

Method two

1. Remove the three trouser rings behind the trousers first, and the front and left two do not need to be removed. 2. The waist circumference is only removed from the back piece, and the front piece does not need to be removed. 3. Remove a section of the bone line on both sides.

4. The side bones on both sides are reduced, because the waist circumference is small, of course, the side bones must also be reduced, otherwise the waist circumference will not go up. 5. Mark and stitch the part to be changed. 6. After suturing, cut off the excess part, or not, and put it again to prevent obesity in the future.

7. After changing the waist circumference, change the interface, which is just under the trouser ring, so that you can't see that there is an interface.

The main principle

Fold a small section slightly inward on both sides of the waistband according to your own needs, and then sew it up, and the side seam and front and middle seam can be sewn into a few centimeters. <>

Step 1

1. Prepare the required tools and materials.

2. Disassemble the waist of the pants and unpack the elastic band.

3. If there is no elastic band, use rag strips instead, cut a rag strip suitable for the length with scissors, and then fold it into a cloth strip with the same narrow elastic width of the pants, and sew it with a sewing machine. This makes it stronger and less likely to curl.

4. Sew the two ends of the sewn strip of cloth on both sides of the elastic band.

5. Tidy up the waist of the trousers, fold the edges, and complete the sewing. The beautiful pants are remodeled.

If you find that the waistband is too small and you need to change to a larger size, this is a relatively simple task. It doesn't take a lot of experience or skill, just some manual skills. This post will give you some simple steps so that you can change your waistband to a bigger one.

The first step is to measure yourself so you know how much you need to add to your waistband. Fold your pants in half and measure the extra length you need near the waistband, usually with an inch or two of fabric at the back.

The second step is to open the sutures. Locate the suture on the waistband of the pants and cut the suture with scissors or sewing scissors.

The third step is to prepare the fabric. Find a piece of cloth of the same color or a similar color and cut it to a length and width comparable to your measurements.

The fourth step is to sew the fabric. The new fabric is folded in half and sewn into a circle with a sewing machine or hand-sewing needle and thread. You can try it on to make sure it's the same size as the loose thread.

The fifth step is to stitch the new fabric. Fix the new fabric to the suture line. Stitch them together with a needle and thread. You can use a sewing machine or hand sewing, depending on your personal preference and proficiency.

The final step is to sort out and fix the sutures. Fold the sutures inward and sew them together with a sewing machine. You can then check that the sutures are intact and if any additional material needs to be added.

Overall, it is not a difficult task to make the waistband bigger, just a few simple manual skills. By following the steps above, you should be able to successfully complete the task in less than an hour and have your ideal pants.

Here's how:Tools: scissors and needle and thread.

1. First turn the pants to the back and use scissors to cut the waistband of the pants at the back. 2. Seal the cut place with a needle and thread, and finally lock the edge, and you're done.

Rubber band: The way to not change the size is to find a way to button the pants, you can use a rubber band to circle the buttons of the pants, and then put the rubber band into the hole on the other side of the pants, wait until the rubber band passes through this eye, then pull it back, and then buckle it to the button.

You need to use scissors and needles, 1. First turn the pants to the back and use scissors to cut the waistband of the back pants.

2. Seal the cut place with a needle and thread, and finally lock the edge, and you're done.