How to set up a wireless router for fiber broadband?

The installation and setup of the router is as follows:

1.First connect the line, you can refer to the figure below.

2.After the line is connected, open a browser, enter the management address and management password of the router, and then enter the router background (the login address and login password of the specific router can refer to the manual or the label on the back of the router).

3.Once you've logged in to your back-office, select Quick Settings, then click Next.

4.Choose the way to access the Internet, usually ADSL users choose the first PPPoE, if you use other network service providers, then choose the following two according to the actual situation, if you don't know how to choose, directly select the first item to automatically select, convenient for novice operations, click next after selection;

5.Enter the password applied for from the network service provider, and go directly to the next step after entering.

6.Set the wifi password, try to make the alphanumeric combination more complicated, and it is not easy to be rubbed off the network.

7.After entering it correctly, it will prompt whether to restart the router, select Yes to confirm the restart of the router, and you can access the Internet normally after restarting the router.

In fact, the optical fiber network cable is similar to our ordinary ** line, the difference is that the optical fiber network cable does not need to be connected to the modem (commonly known as "cat") dial-up Internet, but only needs to connect the optical fiber network cable directly to the computer to dial up the Internet, but many netizens for the optical fiber network cable without the cat, how to connect the router but began to puzzled, the next article will be divided into two parts: the line connection of the optical fiber router and the setting of the router to answer you in detail. Hope it helps.

1. Optical fiber network cable, computer, wireless router connection method

Since there is no cat, the fiber optic network cable needs to be connected directly to the router, and it needs to be connected to a special WAN port of the wireless router, and there are other quad-core LAN ports for users to connect to the computer. In addition, we also need to connect the router to the wireless router, the following is a schematic diagram of the connection of the optical fiber network cable, the computer, and the wireless router:

As shown in the figure above, we see a gray network cable that is connected to the home from the outside network provider, the network cable interface, directly connected to the WAN port of the wireless router, the port is different from other quad-core LAN port interface colors, we can easily distinguish, and the WAN port will be marked below the port. In addition, the yellow network cable is connected to the computer at one end (the author shows you here to connect to the author's notebook), and the other end is connected to any one of the quad-core LAN ports of the wireless router, and finally the black wire is connected to the power box plug, and the overall connection effect is far away, as shown in the following figure:

As shown in the figure above, in order to facilitate the demonstration, the author placed the wireless router on the top of the notebook, and in the next operation, we need to enter the computer to operate, so it is necessary to put the router next to it. The installation of the optical fiber router is basically over here, and then we have to set up the optical fiber wireless router, before setting up, we must first understand the IP default login address of the router and the Internet access and password provided to us by the network provider.

How to find the IP address of the router login and surf the Internet

1. First of all, let's talk about the IP address of the router, the default login address of this different router may be different, most of them are, and the router login user password and password are usually admin, please see the label at the bottom of your wireless router, as shown in the following figure:

The bottom of the router will be marked with the router IP address, user name, password, and other information.

As shown in the figure above, the author is using a TP-Link wireless router, and the IP address of its login management is admin, and the username and password are admin.

1. After connecting the wireless router, enter the address you see on the router in the browser.

2. Enter the corresponding password;

After entering, you will see that you can enter the corresponding account and password, and the initial and password are admin.

3. Select the Setup Wizard;

Enter the operation interface, you will see the setup wizard function, click to enter.

4. Enter the setup wizard interface;

5. Enter the Internet mode setting;

Click Next, enter the Internet access mode settings, and select Dial-up Internet PPPOE.

6. Enter the password;

If you choose PPPoE dial-up Internet access, you need to fill in the Internet account and password, and you will have an account and password when you open broadband, and you can fill it in.

7. Set the password of the router;

To select WPAPSK or WPA2PSK for wireless security, the vertical segment option is highly secure.

8. If the setting is successful, you can set it to keep the mark on the letter.

Here's how:

Situation A: To your home is the optical fiber interface, then you need to go to the computer city to buy a corresponding optical fiber transceiver (also called optical fiber modem, a router with optical fiber communication function can also be), and then connect the optical fiber transceiver to the wireless router through the network cable, log in to the management interface of the wireless router, and enter the account password in the PPPoe according to the broadband dialing method.

Situation B: To your home is already the network cable interface, at this time, just log in to the management interface of the wireless router in the PPPoe dialing option according to the broadband dialing method and enter the account password.

Finally, don't forget to set a password for your wireless

Dear, if you are satisfied, please give a good review

If it is an optical fiber to the cell, and then put a network cable by the switch through your home, it is generally PPPOE, and you can buy a broadband router to get it, the network cable is connected to the WAN port, and the desktop is connected to the LAN port. Simply follow the broadband router setup wizard and enter your broadband username and password. The computer then automatically obtains the IP address and DNS.