Copier Problem 20, Copier Problem to be Resolved

There were 8 responses in total.

Generally general, but second-hand goods are recommended to buy less for the better, this second-hand goods are not warranted, with a broken is not very expensive?

By: I'm from Puning - Probationary period Level 10-11 23:30

Upstairs is right, buy a new one, it's only 5,6000, what's the point, spend this unjust money, in case you buy a piece of garbage, you feel good, repair every day, don't lose you, and I'm angry with you... Hey.

Author: xhq2xhq4 - Assistant Level 2 10-12 01:25

That's right, if you want to do it, do it formally, don't be so restrictive, it's not cost-effective in the end.

Anonymous 10-12 23:17

AF1045 was no longer available, and later 2045 and 3045 were released

Author: Duke Whwh - Assistant Level 2 10-12 23:24

This machine is so old!! Now there are more than 2,000 people who buy a printing and copying table!! Why buy the old one!!

By:75569099 - Probationary Period Level 10-14 19:32

Generally general, but second-hand goods are recommended to buy less for the better, this second-hand goods are not warranted - upstairs is right, buy a new one, it will be 5,6 thousand, what are you doing, spend this unjust money, in case you buy a garbage, you feel good, repair every day, don't lose you, but also angry you... Hey.

That's right, if you want to do it, do it formally, don't be so restrictive, it's not cost-effective in the end.

By: 443681671 - Apprentice Magician Level 2 10-15 18:54

Haven't used it. It shouldn't be good!! In general, you can make a copy! ~~

Haven't used it. It shouldn't be good!! In general, you can make a copy! ~~

It depends on its price, this machine is really not good, but if the bid is low, wait for you to buy it to make some money first, and then buy a new one, and you won't lose money! ~

I've used this.

I can't say too much. I'm afraid some people will be upset to see what I'm saying.

Hehe: This one isn't very good. Think it out for yourself before you use it.

This machine is so old!! Now there are more than 2,000 people who buy a printing and copying table!! Why buy the old one!!

AF1045 was no longer available, and later 2045 and 3045 were released

Buy a new one, just a little money, don't be reluctant to pay!

1. If the laser of the photocopier is damaged or aging, replace the laser, or contact the after-sales personnel to adjust the power of the laser;

2. If the high-voltage plate of the photocopier is damaged or malfunctioning, contact the after-sales personnel to replace the high-voltage plate;

3. If the drum assembly of the photocopier is damaged or the drum core is aging, replace the drum core, or directly replace the set;

4. If the powder of the developing component is uneven, contact the after-sales personnel to disassemble the machine to check whether the powder on the magnetic roller is normal.

Copier Introduction:

A photocopier refers to an electrostatic photocopier, which is a device that uses electrostatic technology to copy documents. The photocopier is an analog method and can only be used to make truthful copies of documents.

Digital photocopiers will make it possible to store, transmit, and typeset images (image composition, addition or deletion of information, partial enlargement or reduction, and correction of errors). It can be connected to computers, word processors, and other microprocessors through interfaces, and becomes an important part of the regional network. Multi-functional, colorful, inexpensive and miniaturized, and high-speed are still important development directions.

1. Paper jam, the paper jam of the photocopier is caused by the failure of the components of the machine itself, as well as the copying environment and human use factors. Check to see if the copy paper is wrinkled by moisture, and if so, replace it with a new one. Look at the machine to see if there is any residual paper that has not been cleaned up at the location of the jam.

If the inspection is normal, turn off the machine and restart the power and make a copy, if it still causes a paper jam, you should contact the maintenance personnel.

2. Add toner, when the panel of the photocopier shows a red light and powder signal, the multiple manuscript printer should be added toner in time, if the powder is not added in time, it can cause the failure of the photocopier or produce the noise of powder impact. When adding toner, shake loose the toner and follow the instructions for adding toner.

3. Add paper, before adding copy paper, check whether the paper is dry and clean, and then straighten out the copy paper, fold it neatly and then put it in the paper tray with the same size and specification.

4. Why is the color of the copy manuscript light, the color of the copy manuscript is light, you can use the manual concentration button to deepen the copy, if it is still light, it may be that the amount of toner is insufficient, the original color is light, the copy paper is damp, and the component failure, the use of substitute toner and other problems, first check whether it is the above problem, after solving the problem, if there is still a problem, you need to contact the maintenance personnel in Zhizhen.

Summary. Hello dear, happy to answer for you. The printer cannot print most of the time due to improper use, installation, and setting of the printer, and viruses, damaged printer drivers, and faulty printer ports will also cause the printer to fail to print.

Hello dear, happy to answer for you. The printer cannot print most of the time due to improper use, installation, and setting of the printer, and viruses, damaged printer drivers, and faulty printer ports will also cause the printer to fail to print.

1. The printer is not in the online state, so the printer cannot be printed on most printers, there is a small light indicating the online status next to the "online" button, and the online indicator should be in a solid state under normal circumstances. If the light is not lit or flashing, the connection is not normal. Please check whether the printer power is turned on, whether the printer power switch is turned on, and whether the printer cable is connected correctly.

2. Turn the printer back on If the online indicator shows that the online is normal, please turn off the printer first, then turn it on, and try to print the document again. This can clear the printed document data stored in the printer's memory and solve many problems, but sometimes this method can cause the printout to be messed up and require a system reboot before printing can work.