How to clean cement stains from plastic basins

Cleaning cement stains from plastic basins can be done in the following ways:

1. Laundry detergent.

Just wipe it with a rag.

2. You can use toothpaste to wipe it. Tea stains on a teacup.

It's all washed off with toothpaste, and it's also useful for basins.

3. Use leftover tea bags, fried things or waste oil that you don't eat. Dry the tea bags first. Then, soak in used oil and gently wipe the dirt on it, and the dirt will come off little by little as if it has melted, so that not only the washbasin and other utensils with a smooth surface can be removed, but also the dirt on the uneven surface of the container.

It can be thoroughly cleaned in the crevices. At this time, a thin layer of oil is left on the basin, and then, with a relatively soft cloth, only a small amount of detergent is poured, and it can be cleaned, and there is no smell of oil.

4. Use 84 disinfectant.

Mix with blisters.

5. Dip it in the dirty powder and brush vigorously with a brush for 10-15 minutes.

6. Rub the laundry detergent with a sassafras ball for 10-15 minutes.

The easiest way to do this is to use toothpaste. Squeeze the toothpaste onto the porcelain and wipe it with a soft cloth or towel, and the porcelain will be clean and will not hurt the porcelain. Similarly, wiping kitchen tiles, flush toilets, rice cooker surfaces, and hand washing at home works well.

Give it a try.

Is dirt on a plastic basin hard to clean? Keep these tips in mind and clean them off with ease.

Cleaning method of injection mold dirt, dry ice cleaning method, waterless cleaning, no pollution, simple cleaning process, high efficiency, energy saving and environmental protection.

How can there be cement? If it is a high-gloss surface, you need to use a makeup sponge to wash the mold water slowly, and be careful not to scratch the mold surface!

Pickling (dilute hydrochloric acid) is recommended.

Dear, the method of removing the cement on the plastic bucket is as follows: 1. First of all, slowly knock the surrounding area to remove it, and use a knife to scrape the blister filled with water for a long time, because the plastic bucket is slippery and not sticky. 2. Secondly, the cement cannot be attached and scraped off with a hard object, and the water must be seen.

3. Finally, take a shovel and knock the wall of the barrel if the cement has hardened. The plastic bucket is soft, the cement is brittle, as long as you tap the wall of the cement barrel, most of the cement will be shaken off, and a very small part can be scraped off with a putty knife. If you do it, you can remove it by tapping it around slowly.

How do you remove cement from plastic drums? Hello dear, it is recommended that the cement can be automatically fallen off by vibrating. Because when the cement sticks to the wall of the plastic barrel, because the structure of the plastic barrel wall is compact and free of gaps and micropores, the cement slurry can only adhere to its surface and will not penetrate into its interior.

When the cement is dry, when the plastic wall is gently hit, it will easily produce a shock wave due to the thinner barrel wall, and under the action of the shock wave, the cement attached to the plastic barrel wall will be cracked and fall off from the barrel wall.

1. Remove the cement from bamboo flakes, scrub with 1000-2000 mesh sandpaper, and do not use iron products to remove it, which will hurt the glazed surface of squatting porcelain. The method of rapid removal is to remove with dilute hydrochloric acid, hydrochloric acid has a strong decomposition ability to cement, no harm to ceramics, but do not flow hydrochloric acid to other places, wear rubber gloves to avoid hydrochloric acid splashing during operation.

2. Hydrochloric acid or phosphoric acid solution and water are mixed in a ratio of 1:5 (if the cement is thicker, you can drop some hydrochloric acid or phosphoric acid solution directly on it first).

3. Pour the prepared water on it, sprinkle it with sawn foam, and use a wooden shovel (don't use metal to leave traces, and don't use steel wool balls to brush the pot). When shoveling, you can also use a rag dipped in water to wet the cement slurry. It's okay to make the peptide head shovel a little stronger, pay attention to cleaning up with the shovel.

When you're done, you can wipe it a few more times.

Removal of cement:

First: Use a small hammer to gently tap the solidified cement, knock the cement off, and then wipe off some traces on the surface with a cloth.

Second: If the surface is not a cement block but a stain of cement water, you can go to the supermarket to buy a special stain remover, and use it according to the instructions after buying it.

Third: scrub with diluted oxalic acid or banana water. Don't forget to protect your hands and wear rubber gloves when scrubbing. Apply it to the cement area with a brush first, and wipe it off with a dry cloth after 3-5 minutes.

Glue removal: 1Apply the usual face oil and wipe it evenly, and then use your fingernails to pick off the part that can be picked off first, and wipe off the rest with a wet towel.

2.Use a hair dryer to blow on the glue-stained area, and you can easily get it off by heating the glue.

3.Rub the wind oil essence on the position of the glue marks, and the glue marks will be wiped off after a while.

4.Use alcohol + eraser.

5.Take a piece of vinegar-stained rag to cover the entire area of the glue marks, and when the glue stains are completely soaked, you can easily remove them with a ruler.

6.Soak it in water, then apply a little dish soap and brush with an old toothbrush.

7.Wipe with a cloth dipped in wine tips or a second pot head.

8.Use soap and a little nitrogen to mix with turpentine.

9.Use a transparent adhesive with good viscosity to repeatedly tear the places with glue marks, and you can also remove some of them, so that the glue marks are no longer obvious. Apply a little sodium water and wipe it off, or use a paint thinner to wipe it off.

10.Wipe with a cotton swab dipped in nail polish remover or wind oil essence to remove the glue marks.

11.Wipe with a special cleaner or sneaker stain remover.

12.If it is a long-standing mark that has hardened, you can use a hot towel to soften it and then try the above methods.

Generally, plastic basins are used in the home, and a layer of dirt will accumulate on the basin after a long time, which is not good-looking and difficult to clean. Here's how to clean the dirt on the plastic basin.

Cleaning Steps:

1. Soak the plastic basin in very hot water for 5-10 minutes (it is very dirty, you can soak it for a while) in order to soften the dirt.

2. Find a few more egg shells and put them in a bowl and crush them into minced pieces.

3. Pour out the water in the plastic basin, soak the rag, dip the eggshell crushed and rub it in a circle on the inner wall of the plastic basin, and rub it back and forth a few more times.

4. Squeeze a little dish soap on the rag and continue to rub it in the basin to achieve the purpose of removing grease stains.

5. Finally, rinse the plastic basin with clean water. Check it out! Is the dirt on the basin all gone?!

Tips for cleaning dirt from plastic basins:

Tip 1: After using the washbasin normally, you can pour the appropriate decontamination powder into the basin, then wipe it with a rag and rinse it with water. You can also wet the towel with hot water after use, then wipe the washbasin with soap, and finally wash it with water, which is a very simple method and will not take up much of your time.

Tip 2: Wrap the leftover tea leaves in gauze, dip them in an appropriate amount of cooking oil and wipe them, and then wash them with a small amount of detergent. Compared with the traditional method of scrubbing vigorously with a vegetable melon cloth, this method avoids scratching the surface of plastic products.

The surface of plastic products will be uneven after scratching, and it is easier to accumulate dirt.

Trick 3: You can squeeze toothpaste on the brush, and then brush the dirt in the plastic washbasin, you can see that the dirt has been brushed off, because the toothpaste generally contains friction agent, it is easy to remove the dirt attached to the smooth surface, and this method is not only simple and convenient to operate, but also will not damage the washbasin, the effect is very good.

Tip 4: Find a good eraser, press and hold the basin to wipe it on the basin, turn the circle, and make sure that all the dirt is gone. Then take a cloth and wipe off the eraser, and after wiping it off, it will be the same as new.

Tip 5: Soak the plastic basin, sprinkle some dry laundry detergent and scrub it vigorously, and it will be clean in a while.