What are the specifications of ceramic tiles What are the specifications and sizes of ceramic tiles

1.This can be seen first, if the budget is limited, you can choose a more conventional style 600 * 600, 800 * 800, are OK, the conventional style also has a lot of choice, and cost-effective. Usually the same brand of tiles, the larger the size will be higher in comparison.

2.According to the choice of house type, small apartment and small area of the house (living room area below 30 square meters), it is recommended to choose small size tiles, because the large size can not be paved in the end. Don't listen to sales blind bbs.

If it is a large area of the room, then you can consider 600*1200, 750*1500, 900*1800. The effect of paving will be very tall and beautiful! The largest size is basically what the villa will consider.

3.Labor cost, choose 600 * 600, 800 * 800 this regular size of floor tiles, labor cost will not increase. But if you choose unconventional size full-body bricks, the later masonry paving will add money!

In addition, the floor tiles are on the wall or something, and the budget is sufficient. In fact, the choice of general tiles for wall tiles is completely sufficient! But it can cost a lot less, and the effect is not bad. The money saved can be spent elsewhere.

The common specifications of wall tiles are 300*450mm, 300*600mm, etc., and the common specifications of floor tiles are 600*600mm, 800*800mm, etc.

The specifications and sizes of tiles are different according to the sizes used in different areas, and the specifications and sizes of tiles in the living room and bedroom are 90 90cm, 60 120cm, 90 180cm, etc.; The specifications and sizes of the living room are 400mm, 600mm, 800mm, 1000mm, etc.; The tile specifications and sizes of the bathroom are 300 400mm, 300 300mm, 250 330mm, etc.; Kitchen and balcony tiles are available in sizes of 30 30 cm, 60 60 cm, etc.

Ceramic tile is made of refractory metal oxide and semi-metal oxide, through the process of grinding, mixing, pressing, glazing and sintering, and forms an acid and alkali resistant porcelain or stone, etc., building or decorative materials, called ceramic tiles. Its raw materials are mostly made of clay, quartz sand, compressed after high temperature, etc., and have high hardness.

Tile purchase tips:

1. Drop a few drops of tea juice or water on the back of the tile, wait for a few minutes, depending on the degree of inhalation and diffusion of the water droplets, the quality is good if it does not absorb water or has a low water absorption rate.

2. Knock on the tile to listen to whether the sound is crisp, the more brittle the sound, the higher the porcelain, the higher the density and the better the hardness.

3. Scratch the tile with a sharp object to see if there are scratches, if there are scratches, it means that the surface hardness is not enough, and the surface of the glaze is polished, and the brick surface will not be cleaned.

4. If the color and chromaticity of the tile are clear and natural, it means that the porcelain degree is high, the chromaticity is not clear, and the porcelain degree is low.

5. When purchasing, observe whether there are pinholes on the surface with the naked eye within one meter, if there is, it means that the glaze is not completely integrated, and it is easy to accumulate dirt.

6. Observation of warpage: whether the side of the tile is straight with the naked eye, if the warping situation is serious, it will affect the firmness of the tile in the future.

7. Check the square tiles: put the four bricks flat on the ground, change their combined edges arbitrarily, and see if the cross and gap in the middle are even.

8. Check the flatness: turn any two bricks opposite each other and rotate one of them; See if it can rotate, if it can rotate, it means that the surface of the brick is uneven.

Tile specificationsIt is also a big problem in the selection of tiles, and the same as the classification of tiles, the specifications of tiles used in different rooms are also different, and the size of the whole room should be taken into account. If the room is too large, it is not suitable for small tiles, and conversely, it is not suitable for large tiles. Now let's briefly introduce the specifications of the ceramic tiles.

1. Generally, if the living room area is less than 30 square meters, consider using 600*600; If it is 30-40 flat, 600*600 or 800*800 can be used; If it is more than 40 square meters, you can consider using 800*800 or even larger.

2. The specifications of kitchen tiles in the current more common are 100 100 and 600, mainly because the tiles are cost-effective and suitable for the cost of the kitchen. Here it is recommended that consumers should choose a better material of ceramic tiles, because tile decoration is different from wood floor decoration, tile decoration is very troublesome, it is best to decorate in place at one time, do not lose big because of small, especially in the kitchen.

3. Tiles can also be customized, providing a unique space tile paving scheme, cutting out different modeling designs according to needs, which is a personalized reprocessing, so the cost is higher, but it is more in line with personal aesthetics and makes a difference.

4. Consider the length and width of the living room: in terms of effect, it is better to pave all the tiles in the entirety, which means that the edge of the brick is not cut or cut less brick, and the waste is reduced as much as possible.

Calculate the number of tiles by area.

Measure the dimensions of the floor wall of the paving space, and calculate the area (length and width).

Calculation formula: total number of pieces = tile paving area (square meters) (length of a single tile and width of a single tile).

For example, if the paving area is 20 square meters, 300 300mm tiles are selected.

Total number of pieces = 20 (pieces.

Note: If there is a decimal number after calculation, it is generally calculated by the method of 'rounding up', that is, 223 pieces, and the construction loss of about 3% must be added before purchasing.

In the spring, it is about the introduction of ceramic tile specifications.

Ceramic tiles are believed to be familiar to everyone, and they are often seen on the walls and floors such as kitchens, bathrooms, balconies, and living rooms. There are many types of ceramic tile colors, thicknesses, shapes, and specifications on the market, so that many friends are at a loss to start and are not sure how to choose, especially the specifications and sizes of tiles. So what are the specifications of ceramic tiles?

Let's take a closer look.

First, what are the specifications of ceramic tiles.

Common floor tile specifications are *30cm and so on. Common wall tile specifications are *10cm and so on.

Second, how to buy ceramic tiles.

1. Look. Carefully observe whether there are black spots, bubbles, pinholes, scratches and other defects on the surface of the tile, and the surface of the high-quality tile is smooth, and there will be no defects such as leakage and grinding. Moreover, there is a clear tile brand mark on the embryo body of the brand product, if it looks blurry, it is not recommended to buy such products.

2. Shake. When buying ceramic tiles, you can try the feel, the same specification and the same thickness of the product, high-quality products feel heavier, on the contrary, and the inferior products feel lighter, because the texture of the tile is related to the density, high-quality tiles have a greater density, and the thickness does not have much to do with the thickness.

3. Listen. You can use one hand to hold the tile, the other hand to tap the tile, listen to the sound to identify the quality of the tile. High-quality tiles will make a calmer sound, while those that sound hollow are low-quality tiles.

4. Flatness.

Take a few tiles and place them on a standard flat surface to see if there is a noticeable difference in height between the tiles.

Conclusion of the article: The specifications of ceramic tiles and the skills of purchasing ceramic tiles are introduced to you here, I hope it will be helpful to you. Since the size specifications of tiles are not fixed, the size is different, and we have to buy according to the area and area of our home when buying.

Rock slab: rich and diverse, widely used, can be used in cabinets, countertops, wardrobes, door panels and other home decoration, with fireproof, wear-resistant, stain-resistant, acid-alkali resistant, easy to clean and other superior physical and chemical properties, specifications are generally more than 900 1800mm;

Ceramic slab: after high-temperature calcination, large-tonnage press pressing, its performance is stable, the expansion coefficient is very small, the hardness is high, wear-resistant, corrosion-resistant, not easy to deform, generally 750x1500mm, 900x1800mm, 800x1600mm and other specifications;

Glazed bricks: with rich color, good anti-slip performance and other advantages, square glazed bricks have 152mm 152mm, 200mm 200mm and other specifications; Rectangular glazed tiles are available in 152mm 200mm, 200mm 300mm and other specifications;

Full-body bricks: the surface is not glazed, the material and color of the front and back are the same, with strong slip resistance and wear resistance, generally 400mm 400mm, 500mm 500mm, 600mm 600mm, 800mm 800mm and other specifications;

Antique bricks: mainly derived from colored glazed bricks, that is, glazed porcelain tiles, with 150 150mm, 300 300mm, 600 600mm, 300 600mm and other specifications.