When the computer is turned on, the logo appears and that s it, something went wrong

Updated on amusement 2024-08-04
4 answers
  1. Anonymous users2024-02-15

    What should I do if my computer has been on the brand logo interface since it was turned on?

    1. If you can't enter the system when you boot up the motherboard logo, you need to restart the TAB button to skip the logo screen or press the DEL key continuously when booting up (the notebook is F2 or its high ridge and it specifies a hotkey) to enter the CMOS setting interface, and turn off the FullScreenLogoShow in the AdvancedBiosFeatures tab to see if the POST information can be displayed, and then determine the problem. 2. Under normal circumstances, according to the prompt information of the black screen and white characters on the screen, press the F1 key to skip the non-fatal error and directly start the electric Qi Yun infiltration brain, or press the del key to enter the CMOS, and then press F9 to load the predefined parameters or select LoadoptimizedDefaults (load the default value of high performance) or LoadFail-SafeDefaults (to load the default value of failure safety), and then press F10 to save and exit the restart. 3. If the original CMOS parameters are not saved or the system time in CMOS is restored to the factory time after the shutdown and power off, it may be that the motherboard battery is invalid, and the battery needs to be replaced, and then load the predefined parameters and save them according to step 2.

    4. If the above operation is invalid, it means that the hardware exists.

  2. Anonymous users2024-02-14

    Summary. Hello dear, the method is as follows: "Method 1:

    Enter the safe mode to fix 1, first check the power supply problem, check whether the connection cable has fallen off and the contact is poor. If not, press the power button, if the system logo appears, press and hold the power button to power off, repeat three times. 2. Wait for the diagnosis and repair to be completed, click Advanced Options3, >> Startup Settings, click the Restart button4, press F4 to enter safe mode5, uninstall the recently installed software in safe mode, driver, and scan for viruses.

    It's a good idea to remember if you set up your computer before it won't turn on, so you can quickly fix the problem. Method 2: If you can't enter the safe mode, most of them are hardware problems1, check the display first, you can unplug the data cable of the display, only connect the power cable, if the display shows no signal, there is no problem2, disassemble the machine, find the memory module on the motherboard, break the buckles on both sides, and remove the memory module.

    Use the eraser to wipe the gold finger and put it back in to try to turn it on. If you have other memory modules, you can also replace them and try to boot them on. If there is no problem, use the same method to detect the problem of the graphics card 3, the hard disk can try to change the interface connection, wait for a few minutes and then turn on Method 3:

    If the above methods cannot be solved, we can also use the USB flash drive boot disk to reinstall the system.

    What should I do if my computer has been on the brand logo interface since it was turned on?

    Dear, hello, the method is as follows: "Method 1: Enter the safe mode to repair 1, first check the power supply problem, check whether the connection cable has fallen off, and the contact is poor.

    If not, press the power button, if the system logo appears, press and hold the power button to power off, repeat three times. 2. Wait for the diagnosis and repair to be completed, click Advanced Options3, >> Startup Settings, click the Restart button4, press F4 to enter safe mode5, uninstall the recently installed software in safe mode, driver, and scan for viruses. It's a good idea to remember if you set up your computer before it won't turn on, so you can quickly fix the problem.

    Method 2: If you can't enter the crack shouting safety mode, most of them are hardware problems1, first check the problem of the display, you can unplug the data cable of the display, only connect the power cable, if there is no signal display, there is no problem2, disassemble the machine, find the memory module on the motherboard, break the buckles on both sides, and remove the memory module. Use the eraser to wipe the gold finger and put it back in to try to turn it on.

    If you have other memory modules, you can also replace them and try to boot them on. (If you don't understand this disassembly, find a professional to deal with it) If you don't ask the rock pants question, use the same method to detect the graphics card problem 3, the hard disk can try to change the interface connection, wait for a few minutes and then boot the method 3: Reinstall the system If the above methods are excluded and cannot be solved, we can also use the U disk boot disk to reinstall the system to solve it.

  3. Anonymous users2024-02-13

    What should I do if my computer has been on the brand logo interface since it was turned on?

    Hello dear. Restart the computer and press the Tab key to skip the logo screen interface, or press the Del key continuously at startup to enter the CMOS settings interface. 2. Turn off "Full Screen Logo Show" under "Advanced BIOS Features" to detect POST problems.

    3. Press the F1 key to skip and start the computer directly, then press the F9 key to load the predefined parameters, select "Load Optimized Defaults", and then press the F10 key to save and exit and restart to solve the problem. 4. If the original CMOS parameters are not stored after restarting, it may be that the motherboard battery is faulty. After replacing the battery, repeat the above operation.

    5. If none of the above methods work, you need to reinsert the hard disk or repair the master boot record of the hard disk or reinstall the system, and finally consider replacing the hard disk.

  4. Anonymous users2024-02-12

    Summary. Pro, it may be caused by an external device.

    What should I do if my computer has been on the brand logo interface since it was turned on?

    Pro, it may be caused by an external device.

    Only keep the ** cable of the monitor and turn it back on; If the motherboard is faulty, you need to restore the BIOS to the factory settings and change the information settings; If you have problems with the hard disk or hard disk data cable, you can unplug the hard disk and reboot it; If the memory or motherboard fails, you can remove the memory module and wipe the gold finger, and then plug it back in, and the motherboard needs to be sent to the after-sales service for repair or replace with a new motherboard.

    Hope it helps, dear.

    It has nothing to do with external connections, I ruled it out. It's a laptop.

    Dear, the problem with the motherboard.

    Last night, the computer was hanging with a game.,Good chain Zen may have been a long time.,Suddenly a blue screen appeared.。 After the forced shutdown, turning on the phone again becomes a circle in the logo, and it gets stuck after five or six turns. Youchen is still like this when he wakes up in the morning today.

    If it's a problem with the main board of the mountain, how to solve it?

    Dear, go to the after-sales service to overhaul the motherboard hardware and replace the components.

    All right. Okay, dear

Related questions
9 answers2024-08-04

Computer freezes are generally a memory problem

1.Insufficient memory capacity, applications taking up too much memory space will cause crashes; >>>More

6 answers2024-08-04

It's nothing, just click on it and start it normally.

One. Reboot the system – sometimes it's just a program or driver that makes a mistake and they get over after a reboot. >>>More

27 answers2024-08-04

The emergence of this problem is relatively common, and there are several main aspects: >>>More

8 answers2024-08-04

1. Turn off the machine, and then turn it on and keep pressing F8 to select the correct configuration for the last time. >>>More

14 answers2024-08-04

Analysis: This boot menu appears automatically, indicating that the system is corrupted and needs to be reinstalled. You have an optical drive, then the disc is installed, put the system disc into the optical drive, and then select the first line enter. >>>More