How to set up a multi WAN port for multiple WAN ports?

Xinquanxiang is the first multi-WAN router in the country, and it can indeed achieve bandwidth superposition technically, and we have also tested it, and now we are using NUR8555M multi-WAN routers.

Well. Honestly, I recommend Xinxiang.

Because I see the real effect, it's not okay for you k me.

LZ has not been fooled once, At present, as long as Xinxiang can really achieve bandwidth superposition, what Aitai Flying Fish Star Xia Nuo H3C Cisco and other multi-WAN routers are not good.

It is highly recommended that lz go to use Xinxiang, and only then will you know when you use it.

LZ is violent!! ~

2: Xinxiang's multi-WAN router is OK, but other multi-WAN routers can't.

See if the LZ situation has been fooled once, and now it's crazy? In the past, it was used to be fooled?

Really a lot of WAN, hard routing is only thriving.

1. First of all, DHCP is enabled, and the address pool is not set up (it is convenient for the client to get the IP of the same network segment, and after it is enabled, the client will be the default 1..)0 network segment).

2. Then set the LAN information, after completion, the PC will lose connection with the router, re-enable the network card, and you can log in to the router again.

3. The following can be set according to the following figure to set the WAN port parameters. In this way, there will be no mistakes and troubles necessary for undefeated quarrels.

4. After that, the dual-WAN port working mode selects the Huaibian equalization mode (WAN1 20M, WAN2 100M).

5. Remember that if you set the WAN information first, remember to disconnect the connection line of the cat first (the IP of the cat coming in is the IP of the routing WAN port is 1.).2, and the default IP of the route is If it is not opened, there may be a conflict that causes the PC to be unable to log in to the route).

The following describes how to configure a multi-WAN port:

1. Set the interface broadband. Log in to the router management interface, click Interface Settings >> WAN Settings, set the upper rights network parameters of two (or more) WAN ports, fill in the real uplink and downlink bandwidth of the broadband line, and click Save after the parameters are completed. Take the WAN1 port as an example, as shown in the following figure:

Note: 1MB=1024KB, for the convenience of calculation, the document takes 1MB=1000KB as an example.

2. Add user groups from the marketing department and other departments, and control the bandwidth for the two groups in the subsequent control rules.

3. Add marketing rules. Click Transmission Control >> Bandwidth Control >> Bandwidth Control Rules, Custom Rule Name, Data Flow Direction Select lan->wan-all, select Marketing Department for user group, select Bandwidth Mode Independent, and fill in the planned uplink and downlink bandwidth values as follows:

4. Add other department rules. Fill in the control rules for other departments as follows:

5. Enable bandwidth control. On the Bandwidth Control Rules page, select Enable Normal Bandwidth Control and click Save.

For example, if the bandwidth utilization is set to 80%, the bandwidth control rule will take effect when the total bandwidth is 8M.

As early as 2000, when Beijing Xinquanxiang engineers were researching a multi-link solution, they found that there was a huge market demand for multi-WAN technology applications for all Ethernet protocols in China. With the successful development of Xinquanxiang products, the country's first router using multi-WAN technology was born in 2002, and China's first multi-WAN broadband router was named NUR8021.

Routers using multi-WAN technology have physical multiple WAN ports as external network access, so that the intranet computer can use multiple external networks as access lines at the same time through the load balancing function of the multi-WAN router, which greatly improves the network bandwidth. At present, multi-WAN routers mainly have the application advantages of "convergence with clear annihilation and bandwidth" and "one network and multiple lines", which cannot be achieved by traditional single-WAN routers.

Multi-WAN access is achieved through the multi-WAN application of the router. Multi-WAN technology is put into practical use.

Do a few things.

1. Connect the school's network cable to the WAN port of the router and set it to a static IP, but you need to make sure that the IP has no conflicts and can access the Internet normally.

2. Use wired connection route, set the local IP address of the router to, and set the DNS resolution address to ensure that the Internet can be accessed normally under the wired connection.

3. Connect the router in wired mode, and set the wireless network SSID and security password.

4. Disconnect the wired, restart the router, and use the wireless connection.

ok。Do the above step by step in order, and ensure that each step is normal and there is no problem.

If it doesn't work, consider one thing, that is, whether the school's network is bound to a MAC address.

The most important!! The LAN port setting of the router is the local address of the router, that is, the network segment address of your home network, it is important not to connect the home network and the school network in a network segment, that is to say, under the premise of the subnet mask, the school is, and the family is.

I hope you will adopt my answer.

What network is no problem, the port is displayed as 0, there must be a problem with the link, the customer service said that the network is fine, you believe it, you are too sincere.

It is estimated that there is no master willing to come to the door to repair during the festival, and the telecom is shirking its responsibility, don't be polite when you hit the **, it is to report for repair, and ask them to arrange for people to repair it, and you have paid, so that they can provide normal services.

In the port status connection, if you select the Internet access mode, it is automatically obtained.

Confirm that the router is not connected, the broadband cable is directly connected to the computer, and whether you need to dial up.

If you don't need to dial up to access the Internet, confirm whether there is an IP conflict, if there is a conflict, in the router settings interface, click Advanced Settings - LAN Port Settings, change the default to OK.

If you need to dial up to access the Internet, click on the computer desktop "Broadband Connection" to "delete" the "Broadband Username and Password", re-enter, and then click to connect, to see if you can connect, if you can't connect, you need to contact broadband, if you can connect, the router Internet access mode selects ADSL dial-up.

2.If the Internet access method is adsl dial-up, connect the broadband network cable (the network cable that can access the Internet) directly to the computer, and then click on the computer desktop "broadband connection" to "delete" the broadband username and password, re-enter, and then click to connect, to see if you can connect it, if the connection is not error**691 is the account password input error.

If you can connect, you can clone it.

Connect the broadband cable back to the WAN port of the router, use a network cable to connect the computer to any one of the 1 2 3 interfaces of the router, click Advanced Settings - MAC Clone, Manually Clone - Clone MAC Address, and click OK if the address does not start with C8:3A:35.

When cloning, you need to take a network cable to connect the computer to any one of the router 1 2 3 interfaces, do not connect the wireless signal of the router ).

3.Restart your router --- clicking System Tools.

After restarting, go to the advanced settings again to check the connection status, and it shows "Connected", then you can surf the Internet.