How to deal with the water heater that only produces hot water but does not produce cold water?

1. If there is a problem of only hot water but not cold water, it may be that the pressure of the cold water pipe is too small, resulting in the water pressure not coming up, especially during the peak period of water use, at this time, for some areas with unstable water pressure, it is easy to have such a problem. Turn on the electric water heater.

Or a gas water heater.

, there is only hot water**, but no cold water.

2. There may be a problem with the mixing valve, and there is a failure between the cold water pipe and the mixing valve, which will also lead to only hot water**, but no cold water coming out.

3. If there is still no cold water after the cold water valve is opened, it is also possible that the cold water pipeline is blocked. If the layout of the pipeline is unreasonable, the choice is some cast iron pipes, it is easy to breed scale, and it is easy to have the problem of blockage in the later stage.

The water heater only produces hot water but does not produce cold water because the water pressure is not enough, maybe the cold water valve is closed, it may not be opened, and something is blocked in the water pipe.

The water heater is the hot water, and the water is the tap water, each of which is its own.

Electric water heaters can be divided into according to the size of heating power.

The water storage type (also known as the volumetric type or heat storage type) can be further distinguished into the vertical type. Electric water heaters can be divided into water storage type (also known as volumetric type or heat storage type) according to the size of heating power, according to different installation methods.

Water heaters that use electricity as energy for heating are usually called electric water heaters, rapid heating (also known as semi-storage type), three kinds of water heaters only produce hot water but do not produce cold water, instantaneous type, instantaneous type; The storage type is the main form of electric water heater, the floor type. According to the pressure or not, rapid heating type (also known as semi-water storage type) three kinds:

Whether the cool water end of the mixing valve is opened, or whether the mixing valve is screwed in the direction of the cooling water. According to the heating method, if there is hot water coming out, it means that there is no problem with water pressure, which can be divided into household and commercial, cold water supply problems, resistance wires.

Classify. It is one of the three major water heaters alongside gas water heaters, silicon pipes, and solar water heaters.

1. Horizontal type, which can be divided into open type (simple type) and closed type (pressure type), as well as the newly listed integrated type with the integrated design of the bathroom cabinet, according to the use of the road, can be divided into magnetic energy (6 days ago).

Hello dear and happy to answer for you. The solution to the water heater is as follows: 1. The water heater safety valve is faulty

If there is a problem with the safety valve of the water heater, the internal pressure rises after the power is turned on, and the water will flow out of the safety hole, and the water will flow back to the water pipe to avoid the expansion of the cold water after heating. So, the end result is that the water heater doesn't produce hot water. The easiest solution is to replace the safety valve again and let the internal pressure of the water heater return to normal.

2. Internal blockage of the water heater: The internal blockage of the water heater, the accumulation of a large amount of dirt, and the failure to be removed in time will also lead to the situation that the water heater does not produce hot water, the easiest solution is to disassemble the water heater, clean the filter screen, and clean the inside together. 3. Damage to main parts:

The damage to the internal parts of the water heater will affect the normal use, and even lead to the situation that there is no hot water in serious cases. To solve the problem, the first thing to do is to find the damaged part and replace it with a new one. 4. Insufficient water:

When the amount of water is too small, the water heater will not be able to heat normally, and will only produce cold water, not hot water. In this case, check the amount of water and adjust the water environment in your home. The above is all the answers of the answer, I hope it can help you, and I wish you a happy life

Answer: There are many reasons why the solar water heater can only put hot water and cannot release cold water, such as: the vacuum pipe of the solar water heater is damaged, the sewer pipe, valve or joint is leaking, the tap water pressure is too high and the hot water cannot flow out, and the solar water heater is multi-way water, and there is a string of water.

Well, you can see why the specific reason I sent you is why there is no cold water, and there is a solution, you can take a look at these specific problems and get it yourself, if you really can't, you can find a maintenance master to come and show you, it may be that the cold water pipe is blocked or the valve is not opened, and it is also possible that it is damaged and frozen.

Generally, winter comes too quickly this year, so it should be frozen, or it will freeze your hands, so it will not be allowed to come out of cold water.

You can take a look at the detailed information I posted above.

First, the cold water valve is closed: The hot water outlet of the water heater usually needs the tap water pressure to push, and the cold water valve closure will cause the water pressure to be insufficient, resulting in only cold water but no hot water.

2.The second is the safety valve problem: the water heater cannot enter the water, and eventually the water heater cannot produce hot water.

3.The third is that the inside of the water heater is too dirty: for example, the scale of the magnesium rod is too thick, which makes it difficult to heat.

First of all, it may be that the cold water inlet valve is closed or the cold water pressure is low, it is recommended to re-open the cold carry hole Sakura water valve. Secondly, it may be that the safety valve of the water heater is faulty, and it is recommended to ask a specialist to overhaul it. In addition, too much limescale inside the water heater may also cause serious blockage, so it is recommended to ask a specialist to clean it.

It is also possible that the water heater system is faulty, such as failure to ignite, etc., it is recommended to ask a specialist for maintenance. In addition, there are many reasons why the electric water heater only produces cold water and does not produce hot water, it may be that the water heater is not connected to the power normally, it is recommended to make sure that the water heater is connected to the power before using it. It may also be that the heating part of the water heater is damaged, and it is recommended to replace the heating parts with new ones in time.

In addition, the temperature control switch is set too low, the amount of water is too small, the hot water pipe is blocked, and the main components are damaged, etc., which may also cause the water heater to only produce cold water but not hot water, and it is necessary to investigate and solve the problem one by one.

The reason why the hot water device only produces cold water and does not produce hot water.

1.The cold water inlet valve is closed: reopen.

2.The water heater's safety valve is faulty: it needs to be replaced.

3.Inside the water heater is clogged with limescale: Disassemble the hot silver water controller and clean the filter and the inside.

4.Water heater system failure: ask a specialist for repair.

5.Frequent use of hot water, the water in the tank has not been heated: close the outlet valve and let the water in the tank heat up before use.

6.Water cooling due to power failure: Check if there is electricity at the outlet and if the power supply is going into the water heater circuit.

7.The temperature switch is set too low: it is best to set it at about 80%.

8.The pressure of the cold water pipe is too low: the water pressure cannot be increased.

9.Failure between the chiller pipe and the mixing valve.

Summary. Hello, I am happy to serve you and give you the following answers: 1. Check whether the power supply of the water heater is turned on, and check whether the temperature regulator of the water heater is adjusted to the highest temperature; 2. Check whether there is water in the water tank of the water heater, if there is no water, ** water; 3. Check whether the electric heating pipe of the water heater is damaged, if there is damage, please replace it in time; 4. Check whether the temperature sensor of the water heater is damaged, if there is damage, please replace it in time; 5. Check whether the temperature protection switch of the water heater is damaged, if there is damage, please replace it in time.

Hello, it is very high-end to serve you and give you the following answers: 1. Check whether the power supply of the water heater is turned on, and check whether the temperature regulator of the water heater is adjusted to the highest temperature; 2. Check whether there is water in the water tank of the water heater, if there is no water, ** water; 3. Check whether the electric heating pipe of the water heater is damaged, if there is damage, please replace it in time; 4. Check whether the temperature sensor of the water heater is damaged, if there is damage, please replace it in time; 5. Check whether the temperature protection switch of the water heater is damaged, and if there is damage, please replace it in time.

Can you elaborate on that a little bit more?

Hello, it is very high-end to serve you and give you the following answers: 1. Check whether the power supply of the water heater is turned on, and check whether the temperature regulator of the water heater is adjusted to the highest temperature; 2. Check whether there is water in the water tank of the water heater, if there is no water, ** water; 3. Check whether the electric heating pipe of the water heater is damaged, if there is damage, please replace it in time; 4. Check whether the temperature sensor of the water heater is damaged, if there is damage, please replace it in time; 5. Check whether the temperature protection switch of the water heater is damaged, and if there is damage, please replace it in time.

The solution to the water heater only produces cold water but does not produce hot water is: check whether the power supply is connected, check whether there is a problem with the wiring, check whether there is a problem with the electric wall of the water heater, check whether the heater is faulty, and check whether the water pressure of the water heater is normal.

1. Check whether the power supply is turned on: The water heater must be connected to the power supply to work, so checking whether the power supply is turned on is the first step to solve the problem that the water heater only produces cold water but does not produce hot water.

2. Check whether there is a problem with the wiring: the water heater needs the support of the wire when it is working, if there is a problem with the wire, such as a short circuit or open circuit, the cover will cause the water heater to only produce cold water but not hot water. This is where the wires need to be checked for problems.

3. Check whether there is a problem with the electric wall of the water heater: The electric wall of the water heater is an important safety device, if there is a problem with the electric wall, it will cause the water heater to fail to heat the water. At this time, it is necessary to check whether there is a problem with the electric wall.

4. Check whether the heater is faulty: the heater of the water heater is the key equipment to produce hot water, if the heater fails, it will cause the water heater to only produce cold water but not hot water. In this case, it is necessary to check whether the heater is faulty.

5. Check whether the water pressure of the water heater is normal: when the water heater is working, you need to ensure that the water pressure is normal, if the water pressure is insufficient, it will cause the water heater to not work normally. At this time, it is necessary to check whether the water pressure of the water heater is normal.