The washing light of the automatic washing machine keeps flashing and not turning

There are several reasons why the drum of an automatic washing machine does not turn:

The solenoid valve does not work after powering on: check whether the power supply wiring is in poor contact, and it is necessary to rewire and connect the connector. Check whether the power supply voltage is adjusted to the normal position range within the operating range.

Check if the coil is desoldered, it needs to be re-soldered, and if the coil is short-circuited, the coil needs to be replaced. If the fluid temperature is too high, it is necessary to replace the corresponding solenoid valve, and there are impurities that make the main valve core and moving iron core of the solenoid valve stuck, so it needs to be cleaned.

Faulty water level detection switch: due to oxidation, dirt or ablation of the contact, resulting in poor contact and unable to turn on the power supply, causing water ingress, the water level switch should be overhauled or replaced.

If the pressure pipe is easy to wear and crack due to long use, or the pressure pipe is in poor contact with the water level switch and the outer barrel air nozzle, the air leakage caused by disconnection may also lead to more than water ingress. Because the computer board is not under pressure and the water level switch does not work, it is misunderstood that the water level has not reached and the water has not stopped, at this time, the pressure pipe should be checked for wear and whether the two joints have poor contact or disconnection.

Due to the long use time, there is a foreign object blocking the mouth of the air valve, resulting in the pressure can not be transmitted to the pressure switch, at this time the large nut should be unscrewed, and then take out the inner barrel to take out the foreign body blocking the air valve.

Solution: While replacing the water level switch or water level sensor, check whether there is air leakage in the trachea connected to it, and contact professional maintenance personnel for maintenance if necessary.

If you haven't turned on the faucet switch, make sure.

There is also a problem with the computer board, so let's rule it out first. If that doesn't work, keep asking.

The washing light and the spinning light of the washing machine of the washing machine are shining and ringing at the same time, and the washing machine is not working.

1. It may be because there are too many clothes placed in the inner cylinder of the washing machine. 2. It may also be because the voltage is abnormal. 3. It may also be because there is a problem with the capacitor of the washing machine.

4. It may also be because of a problem with the motor. Suggested treatment methods: 1. If there are too many clothes placed in the inner cylinder of the washing machine, it is easy to cause the washing machine to be overloaded, which makes the washing machine not rotate.

At this time, you just need to take out some clothes, and you can usually make the washing machine run normally. 2. If the voltage is very low, it is easy to cause the output torque of the washing machine motor to fail to reach the specified value, so that the motor cannot drive the washing machine to run. In this case, the washing machine should be temporarily stopped, or a booster should be added to the circuit so that the voltage in the circuit can be adjusted to a normal value.

3. If the capacitor of the washing machine has a short circuit, open circuit, grounding, aging and other faults, it will naturally cause the motor to fail to start normally, and if the motor cannot start, it will naturally not be able to drive the washing machine to run. In this case, the capacitor that is not working properly should be replaced with a new one. 4. If there is an open circuit in the starting winding of the washing machine motor, it will cause the motor to fail to start normally, and if the motor cannot start, it will naturally not be able to drive the washing machine to run.

At this time, you should find the reason why the motor does not start, and then take appropriate methods to repair it, or directly replace it with a new one.

There are several reasons for this situation, one is because the solenoid valve does not work after being energized, which may be caused by poor contact, and we can check its connection. The second is because the water level detection switch is malfunctioning. The third is that there are a large number of clothes in the washing machine, which are wrapped together, so that the washing machine cannot rotate.

Fourth, the pressure pipe of the washing machine was damaged, so the washing machine did not work. Fifth, because there is a foreign body blocking the valve mouth, the pressure cannot be transmitted to the pressure switch.

In this case, we need to drain the water in the washing machine first, take out the clothes, and then cut off the power to check, if it is a simple problem, we can deal with it ourselves, if it is more complicated, then we need to consult the after-sales service.

Washing machine does not turn the treatment scheme:

The solenoid valve is energized and does not work, we can check whether the lower coil has fallen off, if it falls off, it needs to be re-welded, if it is because the coil is short-circuited, then it needs to be replaced, if the temperature of the flow sun bypass body is too high, then the solenoid valve of the same type needs to be replaced. If there are impurities that cause the solenoid valve to jam, then it needs to be cleaned.

If the water level detection switch fails, it needs to be replaced, because this situation is more complicated, so it is better to find after-sales or professional maintenance personnel to repair.

If there is a foreign object blocking the mouth of the air valve, in this case, you need to unscrew the large nut, take out the inner cylinder of the washing machine, take out the trapped foreign body, and replace it if it is worn.

There are three reasons, the first power switch is indeed bad, measure whether the power switch is broken, don't get on the power supply, press the power switch, see if it jumps, if it doesn't jump, it's good, second, the computer board is bad, the general computer board is bad in other places will cause the computer board to be broken, to check is the water inlet valve and motor. Answer supplement From the question you mentioned above, it is very likely that your power supply voltage is too high, and the voltage is high, and the motor must be protected, so it will cause the computer board to automatically power off. 【】

The switch still jumps [Question].

There is a short circuit inside the machine itself, so when the power is connected, it will be directly short-circuited, and then the switch will start the protection function and directly trip and cut off the power.

1. The total switch power is too small, when starting the washing machine, due to the instantaneous increase in power consumption, the switch trips, although this situation is relatively rare, but it should still be checked, if the switch itself is only a few amperes.

Let's take a look at a larger one.

2. Because the main switch is equipped with a leakage protection device, if the machine itself has leakage, after the power is turned on, the main switch.

It's going to trip.

At the beginning of the washing machine, the button flashed a little, and finally there was no power.

Summary. The reason why the indicator light of the washing machine does not work: 1. It may be a power outage caused by a blown fuse, a trip of the air switch or a damaged power socket, which makes the washing machine not work 2. The flashing of the indicator lights of the washing machine may be due to the alarm display, the water pipe, power supply, etc. are not installed, or other reasons that do not operate normally.

3. Check whether the drum lid of the washing machine is tightly closed, if the lid door is not closed tightly, it will cause the washing machine indicator light to flash and not start.

The washing machine light is flashing and flashing, it just doesn't work.

This question is up to me, it takes a little time to type, so please be patient.

The reason why the indicator light of the washing machine does not work when it flashes: 1. It may be that the power failure caused by the fuse blowing, the tripping of the bright air switch or the damage of the power socket makes the washing machine not work 2. The flashing of the indicator lights of the washing machine may be due to the alarm display, the water pipe, power supply, etc. are not installed, or other reasons that are not in accordance with the normal operation. 3. Check whether the drum lid of the Hongqi washing machine is tightly closed, if the cover door is not closed tightly, it will cause the washing machine indicator light to flash and not start.

4. Artificial water addition does not reach the water level specified in the required washing. 5. The filter screen of the washing machine is blocked by dirty and wide weights, destroyed things or other foreign objects, which makes the washing machine insufficient power, resulting in clever operation and quiet motion, so the washing machine does not work.

If my answer is helpful to you, please give a thumbs up (comment in the lower left corner), look forward to your like, your efforts are very important to me, and your support is also the driving force for my progress. If you feel that I am satisfied with the answer of Fu Lu, you can click on my avatar for one-on-one consultation. Finally, I wish you good health and a good mood!