Why can t the automatic washing machine be automatic when washing 40

How do you say "I can't automatically do it when I wash it"? Here is the workflow of a fully automatic washing machine, can you tell me at which step the problem occurred and what is the phenomenon? Is it a roller or a roller?

Workflow of a fully automatic washing machine:

1. Press the power switch of the washing machine - the power prompt light is on. That is, this part of the circuit is OK. Otherwise, check the socket, on-board power switch and fuse, etc.;

2. Press the start button of the washing machine:

1) Start the water intake. Is your water ingress? --What if you haven't checked if the faucet is turned on?

Is the water inlet solenoid valve electrified? If there is no power, the computer board is faulty (usually the thyristor that controls the water inlet part is broken, otherwise the solenoid valve is broken and needs to be replaced); If the solenoid valve has been energized (usually the sound of "Weng Weng" can be heard) and no water has entered, it means that the valve core of the solenoid valve is stuck or other faults cause the solenoid valve to not open.

2) After the water intake is completed. Can your water intake stop automatically? --It can automatically stop indicating that the water level switch is good, otherwise replace the water level switch or water level sensor and check whether there is air leakage in the test hose connected to it, and add treatment.

3) The wave wheel turns to start the laundry. Do your wheels turn? No rotation – that could be a motor system problem, such as a capacitor or motor problem;

4) Can it be drained automatically after washing? If not, it may be a failure of the drainage motor (the motor burns out a lot), please deal with it accordingly.

5) Finally, dehydration, can it be dehydrated? If you can dehydrate alone, and the program cannot be dehydrated, it means that the water level switch is broken or the connecting pipe is leaking; If you can't spin it, check the door safety switch and water level switch. :

Zhongyi automatic washing machine can not be automatic when washing the cause and solution:

1. The computer board is broken, replace the computer board.

2. Communication failure, check the communication line.

3. The system program is chaotic, and the chip is replaced.

Favorite automatic washing machine features:

1. Streamlined appearance, beautiful and concise;

2. New planetary gear reducer, shock absorption and noise reduction;

3. The use of new oil seals can completely eliminate water leakage and significantly improve the service life of the reducer;

4. All-plastic closed base, anti-rust, anti-rat, vibration damping, sound insulation;

5. Washing or rinsing, dehydration can be carried out at the same time;

6. Automatic filtration of wire chips.

It may be that the program is selected incorrectly, and fully automatic is selected.

1. It may be that the clothes washed inside are not flat, or there is a problem of overweight washing. 2. It may be that the wave wheel of the washing machine is broken, and the teeth of the wave wheel are smoothed, causing the rotating shaft to be idling. 3. The voltage is too low, so that the motor can not drive the drum to work or the capacitor has a problem, resulting in a decrease in the capacitance value.

Suggested treatment: 1. Before washing clothes, set the appropriate washing program according to the number and type of clothes, if the number of clothes is moderate, then choose the standard washing mode, if it is in summer, there are fewer clothes, you can choose a weak washing program, which can play a good water-saving effect and clean it faster. 2. The starting capacitor of the motor is caused, the starting capacitor of the motor is damaged, the motor can not start, and the buzzing sound will also cause the automatic washing machine not to wash, the treatment method, replace the starting capacitor of the motor, and the starting winding in the motor will also cause the motor to not start, and the motor makes a buzzing sound.

3. If the tooth of the wave wheel is smoothed, resulting in the rotation shaft being idling and the automatic washing machine is not washed, the wave wheel of the same specification can be replaced. 4. The humming sound of the motor is caused by the decline of the capacitance value, and the capacitor can be replaced.

Summary. There are the following reasons why the washing machine has been non-stop.

Why does the automatic washing machine keep washing clothes non-stop.

There are the following reasons why the washing machine has been non-stop.

1. It may be due to the overheating of the washing machine motor caused by the external environment and excessive washing of clothes, and the motor thermal protector will automatically disconnect the circuit to stop the washing machine from working.

2. Please unplug the power plug first, and see if the ventilation system of the washing machine is not very good, or the ventilation hole at the bottom of the washing machine is blocked, and the heat dissipation is poor.

3. Check whether the laundry washed in the washing machine is excessive, if it is excessive, please take out part of the laundry before washing.

4. Check whether the voltage is normal, when the voltage is too high or too low, the washing machine may also have the above situation, at this time, you need to wait for the voltage to be normal before using the washing machine.

5. Check whether the belt is loose, please adjust the belt.

6. Check whether the motor is in poor contact.

We're glad to answer your questions! If it helps you, you can give it a thumbs up! Have a great day! Thank you!

: It could be that the lid of the washing machine was opened, causing the washing machine to stop while washing. Because the washing machine has a device on the top cover to connect the circuit, once the lid of the washing machine is opened, it will cause the circuit to be cut off; In addition, if the circuit device of the top cover has poor contact, it will also cause the washing to stop; In addition, if the drain pipe is clogged and the water level switch cannot be restored to its original position, the washing machine will stop running when the dewatering process begins. Finally, if a foreign object gets stuck in the roller during the cleaning process, it will also cause the washing to stop.

Additional information: How to extend the life of a washing machine?

1. When using the washing machine, do not put too much clothes in order to prevent the washing machine from being overloaded.

2. Before washing clothes, you need to take out all the things inside the clothes to avoid damage to the inner wall of the washing machine under the action of water rotation.

3. After washing clothes, do not close the lid of the washing machine immediately, you should open the lid and wait for all the water in it to volatilize before closing.

First, if the washing machine appears E17, it is a drain timeout, which may be a blocked drain valve, or a damaged drain pump.

The last two minutes are the spinning procedure, which cannot stop indicating that the clothes are placed unevenly, and the washing machine will automatically add water to readjust until the clothes can be turned up evenly, which is generally caused by too few clothes, can not be evenly distributed, or contains a piece of clothing with excessive water absorption such as down jackets.

Second, the fault handling method:

1. Turn on the drain pump first and clean up the dirt inside.

2. Check whether the drain pipe is blocked, it is recommended to clean it up.

3. Check whether the drain pump plug-in wire is loose, whether the drain pump has been damaged, and whether there is a voltage channel drain pump.

4. If there is no voltage to the drainage pump, focus on checking the program controller or computer board.

It can definitely be paused, search by brand.