The fully automatic washing machine does not store water and keeps draining what is the reason

1.If there is a large foreign object in the spool of the drain valve of the washing machine, it will jam the drain valve spool and cause it to be unable to return to its original position, so that the water inlet and drain of the washing machine will occur at the same time. In this case, it is necessary to close the inlet valve of the washing machine and remove the odor stuck to the valve core before it can be used normally.

2.If there is a problem with the washing machine drain traction equipment, the drain cable cannot be returned to its original position, resulting in water ingress and drainage at the same time. At this time, it is necessary to repair the damaged drain tractor of the washing machine in time.

If the damage is significant, the tractor needs to be replaced. 3.If there is an abnormality in the water level switch or sensing device inside the washing machine, then after the water enters, the pressure generated by the water level cannot be felt, so the water enters and exits at the same time, and the water will not be stored.

For this phenomenon, what we need to do is to detect whether the water level switch or sensor is damaged. Just remove it and replace it with a new one. 4.

If the water pressure air duct inside the washing machine is damaged or loose, it will not be able to provide the required pressure to the water level switch, resulting in no water storage in the washing machine. If there is a problem with the water pressure airway, if it is loose, tighten it and you can use it. If it is damaged, it needs to be disassembled, and then the hydraulic airway of the same model is selected for replacement, and it can be used normally.

<> the reasons why the automatic washing machine does not store water and keeps draining are: the belt on the motor slips off, the motor is damaged, or the power supply is aging, the line is broken, the drainage tractor is faulty, or the water seal is damaged or the valve spring of the water seal is broken, the water level switch or water level sensor is faulty, and the water pressure air guide pipe is broken or loose, it is recommended to immediately check and replace the accessories or report for repair.

When encountering this phenomenon, directly check the drainage system of the washing machine, generally the drainage system is faulty, causing the washing machine to be drained all the time, no matter how much water enters the water inlet pipe, it will eventually be discharged from the drainage pipe, check whether the drainage valve of the washing machine has been open, if so, just turn off the drainage valve manually. However, if there are frequent cases where the drain valve cannot close automatically, you need to find a maintenance person to replace a new drain valve. In addition, the following aspects are investigated:

1. Check again whether the drain valve of the washing machine is stuck by foreign objects, resulting in the drain valve not being able to close normally or not being able to close tightly, and the washing machine will flow out from here after the water enters. At this point, cleaning up what is stuck in the drain valve will solve the problem. 2. You also need to check whether the drain valve of the washing machine is not installed properly, and the phenomenon of displacement has occurred, which will also cause the water entering the washing machine barrel to leak out from here.

3. Finally, check whether the computer board of the washing machine is faulty, resulting in the wrong washing machine instruction, if so, directly replace the new computer board, and this problem can be solved.

The washing machine does not store water and has been draining the water to check the method: 1. Check whether there are foreign objects (coins, brooches, buttons, etc.) stuck in the drain valve core, resulting in the drain valve core cannot be returned to the position and cannot turn off the water, and the foreign body needs to be removed. 2. The water level switch or water level sensor is faulty, and the water level pressure cannot be sensed, resulting in continuous drainage, and the water level switch or water level sensor is replaced.

1. If the water has been drained but the motor does not rotate, see if it rings after timing. If it rings, then the belt on the motor has slipped. If it doesn't ring, it may be that the motor itself is broken, or the power supply is aging and the wire is broken.

2. Check that the drainage tractor (drainage motor) is faulty, and the drainage cable does not return, resulting in drainage while entering the water, and the solution is to replace the drainage tractor.

3. The water seal in the drainage pipe is not tightly sealed, resulting in water leakage. It is possible that the coin is stuck in the drain pipe, causing the drain valve core to not return to its position and cannot close the water to drain the water while entering the water, open the back cover, take out the circlip, pull out the drain pipe, and reach into the drain pipe with your hand to check if there is a foreign object stuck.

4. It is also possible that the water seal is damaged or the valve spring of the water seal is broken, if this is the case, the only way to change the drain valve is to replace it.

5. Drain water while entering the water, first check whether the drainage pipe is placed too low (not less than, and then check whether the drainage pipe mouth is inserted into the floor drain. If not, see if the water level is too high to submerge the glass. No, adjust the water level switch or solenoid valve or drain pump plug line.

6. Check the failure of the water level switch or water level sensor, the water level pressure cannot be sensed, resulting in drainage while entering the water, and the solution is to replace the water level switch or water level sensor.

7. Check that the water pressure air duct is ruptured or loose, and the pressure to water level switch or water level sensor cannot be provided, resulting in water inlet and drainage, and the solution is to adjust and replace the water pressure air duct.

How to repair the washing machine without water storage and drainage.

The washing machine does not store water and keeps draining the water for the following reasons:1. There is a foreign body in the drain valve.

When a large piece of foreign matter is stuck in the drain valve core of the washing machine, the drain valve core cannot return to its original position, so it will not be able to control the water and drain the water while entering the water.

2. Failure of drainage tractor.

If the drain tractor of the washing machine fails, the drain cable will not return, and the water will drain when the water is ingress.

3. It may be the water level sensor of the washing machine and the computer version is faulty. <>Solution1. If there is a foreign body in the drain valve, in this case, the water inlet switch should be turned off first, and the foreign matter in the drain valve should be taken out.

2. If it is a sensor or computer version failure, it is necessary to repair the corresponding parts to solve it.

3. If the drain tractor is faulty, it is necessary to replace the drain tractor of the washing machine in time or in time.

Possible reasons are:

1.Clogged drains: If the drains are blocked, the water can't flow out, causing the washing machine to drain non-stop. You can clean the drainage pipes or use a pipe cleaner to solve the problem.

2.Drain pump failure: The drain pump is a key component of the washing machine's drainage, and if the drain pump fails, it will cause the washing machine to drain non-stop. The drain pump needs to be replaced.

3.Water level sensor failure: The water level sensor is a component that controls the water level of the washing machine, if the water level sensor fails, it will cause the washing round search machine to misjudge the water level and drain the water all the time. The water level widening sensor needs to be replaced.

4.Control board failure: The control board is the brain of the washing machine, and if the control board fails, it will lead to various problems in the washing machine, including non-stop drainage. The control board needs to be replaced.

The above are the possible causes, it is recommended to contact a professional maintenance personnel for inspection and repair.

1. If there is a large foreign object in the position of the drain valve of the washing machine, it will jam the drain valve core, resulting in the inability to return to the original position, so the washing machine will be drained at the same time.

In this case, you need to close the water inlet valve of the washing machine, remove the odor stuck at the valve core, and use it normally.

2. If there is a problem with the drainage traction equipment of the washing machine, it will cause the drainage cable to fail to return to its original position, resulting in water inlet and drainage being carried out together.

At this time, it is necessary to repair the damaged drain puller of the washing machine in time, and if the damage is large, it is necessary to replace the new puller.

3. If there is an abnormal phenomenon in the water level switch or induction equipment inside the washing machine, then after the water intake, the pressure generated by the water level cannot be felt, and the water inlet and drainage will be carried out at the same time, and the water will not be stored.

For this phenomenon, what needs to be done is to detect whether the specific damage is the water level switch or the induction device, and only need to remove it and replace it with a new one, which can be solved.

4. If the water pressure air duct inside the washing machine is damaged, or loose and falls off, it is impossible to provide the required pressure for the water level switch, resulting in the washing machine not storing water.

If you have a problem with the water pressure airway and if it is loose, simply tighten it and you can use it. If it is damaged, it needs to be disassembled, and then the same type of water pressure air duct is selected for replacement, and it can be used normally.

I concluded: What should I do if the automatic washing machine does not store water and keeps draining, I will introduce it here, do you understand? If the automatic washing machine does not store water, it needs to be disposed of in time, so as not to affect the normal use in the later stage and bring unnecessary trouble to daily home life.

The washing machine drains all the time, probably because there is too much water or the drain pipe is clogged. Here are some of the reasons why Sakura may be in this situation:

1.Too much water: If the water level sensor or control circuit inside the washing machine fails, it can cause the washing machine to drain constantly. In this case, the water level sensor and control circuitry need to be checked to make sure that it is working properly.

2.Clogged drains: Clogged drains can cause poor drainage in the washing machine. In this case, you need to use a soft brush or cleaner to clean the drain to make sure it is clear.

3.Drain valve failure: Drain valve failure can also cause the washing machine to drain poorly. In this case, it is necessary to check that the drain valve is working properly or if it needs to be replaced.

4.Faulty parts inside the washing machine: Faulty parts inside the washing machine can also lead to drainage problems. In this case, parts inside the washing machine need to be repaired or replaced.

If you are unsure of the cause, it is recommended to contact a professional washing machine repairer to ensure that the washing machine can work properly.