The size of the rural energy saving firewood stove, the whole process and size of the rural firewood

Chengdu product promotion - about the installation and use of energy-saving stoves, the need to modify the original stove, and the superstitious and reasonable design of our products makes the installation very convenient! All you need to do is make a slight modification to the original stove! It will be possible to complete the modification in less than a few minutes!

The modification method is now explained as follows: 1. Remove the original stove water tray and stove, and unload the two nozzles that open the air outlet with a wind plate electronically, and the switch is in a straight line for the small fire eye, and the left or right side is the big fire eye. 2. Use a wrench (or needle-nose pliers, etc.) to quietly knock on the iron snorkel under the stove to loosen the cinders and rust attached to the iron snorkel, and then put the gas to let the cinders, rust and other debris in it be discharged.

The purpose of this step is to avoid cinders, rust and other debris from blocking the small hole of the nozzle where the nozzle will be installed. (Turn on the gas stove switch first.) Turn on the gas canister switch.

Two to three seconds will be you, remember! 3. When changing the single-tube energy-saving stove, plug the fire hole with a screw (be sure to add a raw material belt to the thread to avoid air leakage.) Raw material belt, available in plumbing and building materials stores), connect the coal seasonal energy stove to the air outlet hole (i.e., small fire eye) in a straight line with the switch handle, and tighten it (be sure to add a green belt).

If you change to a double-tube energy-saving stove, you only need to put the nozzle on the device according to the size of the stove and the fire eye. It is worth noting that it is necessary to distinguish between large and small fire eyes. Keep an eye out:

There is no need to over-screw the device to avoid cracking the screw. Fourth, after the installation is completed, according to the way of using cooking utensils (frying pan or round pot) at home, properly adjust the top and bottom of the stove, and it is most appropriate to be centimeter away from the bottom of the pot. Fifth, after the end of the above tasks, it can be used normally, just to check the situation of the stove extinguished, when the stove is extinguished normally, 3-5 seconds The appearance of the stove should be red and red, if the red is very slow or not red for a long time, the pressure of the liquefied gas cylinder should be adjusted a little higher, so as to achieve the ideal energy-saving effect SMS or **Please explain that the information comes from the extraordinary classified information.

All content is published by users, and we do not make any guarantees for the products and services promised by sellers. Be cautious if the seller offers products and services that are prohibited by law, the risk of fraud is extremely high.

About 1 meter, the length and width are about the same, it seems to be the same.

The production of rural firewood stoves should first determine the location of the construction, then build the chimney outside the house, and then use bricks to build the stove and the mouth of the pot, and then paste the tiles after completion. The width of the rural firewood stove is generally left and right, and the height is between.

First, the whole process of making rural firewood stoves

1. Determine the construction location, open the flue, and build the chimney. The ground is marked to determine the location, and the wall is marked to determine the height. Smoke exhaust holes are excavated in the walls. Build a chimney outside the house.

2. Ordinary brick stove, including the stove door ash discharge mouth and the stove chamber. The stove is built with refractory bricks, and the stove is filled with crushed sand and gravel between the stove and the stove.

3. Stove cooktop insulation and fire-resistant construction. Fill the insulation material, protect the crushed sand and brick sand used in the stove, and use a pot to compact the refractory mud above the stove, and the refractory mud is smoothed and shaped.

4. Construction of warm water mouth pot mouth. The pot is placed before the insulation material and refractory mud are constructed. The contact position between the pot and the refractory mud is surrounded by steel bars to ensure that the pot mouth is firm. Smoothing the cooktop with mortar is generally 78cm in height.

5. Paste tiles for decoration and install the stove door flue baffle. After completion, you need to wait 15 days before using it.

Second, the size of rural firewood stoves

The height of the cooktop should be between or between. The cooktop width should be between or between.

Introduction to rural firewood stoves

At present, the stoves used in most rural areas are ordinary stoves, and ordinary firewood stoves are composed of hearth, grate, smoke outlet, insulation layer, chimney, ash room, stove door and pot.

Standard size of rural firewood stove: height: the height of the stove should be between or between. Width: The cooktop width should be between or between.

The height and width mentioned here are the finished surface of the cooktop, that is, the net height and net width after completion. Its height should be calculated from the zero height of the floor tiles until the level of the stove.

Its width is also the widest distance of the diameter of the countertop, if the outside of the countertop is curved, its widest diameter should not be exceeded, and then the natural bend transitions to the narrowest distance, and its narrowest diameter should not be lower.

In addition to determining the size of the wood stove, it is also necessary to pay attention to the design of the exhaust flue. After all, a clear smoke exhaust channel will avoid the occurrence of smoke return. The smoke vent at the top of the chimney is preferably set on the roof, at a height of more than one meter.

It should be built vertically, the mortar should be full, ensure airtightness, the inner wall should be smooth, and there should be dust removal holes at the bottom of the chimney.

Precautions for the production of firewood stoves in rural areas

The design size of the wood stove is recommended to be designed according to the actual messy area of the kitchen and the size of the pot, whether it is one pot or two pots. The height of the fighter should be the same as that of the cook, and the height of the internal combustion chamber should also be noted.

In addition, the furnace cannot be under the beam, cannot be backed up, and must rely on a solid wall, otherwise it is not safe. Attention must also be paid to the design of the exhaust flue. After all, a clear smoke exhaust channel will avoid the occurrence of smoke return.

The smoke vent at the top of the chimney is preferably set on the roof, at a height of more than one meter. It should be built vertically, the mortar should be full, ensure airtightness, the inner wall should be smooth, and there should be dust removal holes at the bottom of the chimney. This is to improve the combustion efficiency of the air and increase the design of the grate.

The height should be or; The width should be in or. The above height and width are the finished surface of the cooktop, that is, the net height and net width after completion. Its height should be calculated from the zero height of the floor tiles until the level of the stove.

Its width is also the widest distance of the diameter of the countertop, if the outside of the countertop is curved, its widest diameter should not be exceeded, and then the natural curve transitions to the narrowest distance, and its narrowest diameter should not be lower.

Precautions for kitchen renovation:

1. Waterproof lamps and lanterns such as anti-fog lamps should be used in the kitchen, and the line joints should be strictly treated with waterproof insulating tape to avoid water vapor condensation entering, causing short circuit and fire. Kitchen lighting needs to be divided into two levels: one is the lighting of the whole kitchen, and the other is the lighting of washing, preparation, and operation.

2. There should be a cupboard in the kitchen to put tableware, and there are many pots and pans in the kitchen, if it is exposed, it is easy to get oily stains, and it is difficult to clean, so the kitchen cabinet should be closed; The cupboard should be divided more, and the drawers should be separated to facilitate the storage of all kinds of tableware and kitchenware.

3. The countertop should be made of fireproof and waterproof materials, and the height should be determined based on the height of the person who cooks most often. Usually the height of the worktop is 80-85cm, and there is generally a 40-60cm countertop on each side of the sink. If the dining table is not in the kitchen, then there should also be a 40-60cm countertop next to the stove for temporarily storing freshly cooked dishes.

The back of the kitchen cabinet needs to be made of a water baffle, that is, the back side should be higher than the table surface to prevent the flow to the back of the kitchen cabinet, so that the substrate expands, causing cracking, falling off and other phenomena.

First determine the location, open the flue, build the chimney, then build the stove, the stove stove insulation and fire-resistant construction, then the flue, fire ring, pot mouth construction, and then paste the tile, and finally wait for 15 days to ensure that the cement has solidified. Dimensions: Height should be between or and width should be between or or wide.

Feng Shui taboo

The stove is most taboo to be located in the middle of the kitchen, and there is no support on all sides, indicating that the family's fortune is unstable, the spirit is depressed, and there is a disaster of breaking the wealth. Therefore, the stove must be placed against the wall, which means that there is a backer behind it, which represents the stability of the family and is also very beneficial to health.

The stove should not be under the beam, Feng Shui has the unlucky saying that "the beam presses the top", where the place where you often enter and exit and operate should not be pressed, the stove as a platform for food production, it is even more inappropriate to have the beam on the top, which will be harmful to health.

Traditional Chinese feng shui theory believes that the ancient kitchen stove is a place for cooking and nourishing life, so it should not be too exposed, especially not suitable for being directly charged by the external qi brought by the door.

Rural firewood in the key collapse stove size: height: the height of the stove should be between or between. Width: The cooktop width should be between or between. The whole process is as follows:

Tools: water, bricks, cement, lime, ash leakage net, etc.

1. Draw the frame of the smokeless wood stove and dig a shallow pit of 3 cm down the frame.

2. Configure cement, lime and water according to the correct proportion.

3. Use bricks to build the basic frame of the firewood stove, the bricks are tiled, remember to leave the stove mouth, and the ash at the bottom of the stove is about 25 cm high, which is used to place the ash leakage net.

After the layer of bricks, start to build the smoke outlet, build a smoke outlet about 30 square meters in the middle of the stove to the distance of the back half of the brick, and build it all the way up, and the stove can be close to the waist height. After the frame is completed, determine the division of the cooktop according to the size of the pot.

5. After the division is completed, use cement slurry to smooth the stove, and finally wait for drying, and then you can start to use.