-
Mosaic paving is very simple, as long as the construction pays attention to follow the standard process:
Description of the construction method of the mosaic.
1. Flatten the wall foundation.
2. This step is to smooth the foundation of the wall, and the wall must be smooth and of the same color.
2. Scribing. Draw a line on the wall to note the exact location of each mosaic. Spread the 3 stickers of mosaics side by side on the ground, so that the ash seam between the stickers is the same as the ash seam in one sticker.
Measure the width of the whole. Then use a ruler and a spirit level to draw the measured dimensions vertically and horizontally on the wall to form a large square. Then divide the large squares into 9 squares, and place 1 mosaic in each square.
3. Prepare tile adhesive.
Prepare the proportional mix of tile adhesive and apply the tile adhesive with a plaster, but the area applied should not exceed the area of 9 mosaics. First, use a plaster with a smooth edge to smooth the tile adhesive, and then use a spatula with a serrated edge to create a uniform layer of zigzag stripes. Now, the mosaic is ready to be put on the wall.
4. Pave and fix.
Because the mosaics are made of nets, they can be applied directly to walls that have been coated with tile adhesive. Pave the mosaic vertically. Please note: The gap between the stickers must be consistent with the gray seam of each sticker.
5. Reinforcement. After each tile is positioned, tap the surface of the mosaic with a gray board to make it firmly attached to the wall.
6. Ensure that the ash seam is consistent.
After each tile has been fixed, the gap between the bricks must be determined to be a uniform width before the caulk can be placed. In this way, it is necessary to use a small ash shovel to adjust the ash joint, which is the most patient process in the process of paving mosaic, but it is the most important link in the process of paving work.
7. Caulk.
Prepare the required caulk. Use a small ash shovel, take a small amount of mixed caulk each time, evenly apply it to the surface of the mosaic, and move the small ash shovel diagonally, first from bottom to top, and then from top to bottom, to ensure that all the ash joints can be completely filled and there is no excess residue.
8. Cleaning. Before the caulk dries, start cleaning the mosaic surface. Prepare two buckets, one with new detergent and one with clean water, first soak the rag in the bucket of detergent without wringing it out, and then wipe the surface of the mosaic in a circular motion; Then soak the sponge in the second bucket with a clean bucket and rub the surface of the mosaic with the sponge to wipe off any residue.
Finally, rub the surface with a sponge again until it is clean.
Precautions: Mosaic products, whether they are pasted with nets or paper stickers, must not be wet before pasting.
Selection of construction accessories:
1. Generally, tile adhesive and caulk are selected as the main pasting materials, and the specific dosage can refer to the suggestions of the first businessman.
2. The choice of waterproof materials, this construction party can be purchased in the market, and it is best to consult an experienced swimming pool construction unit.
-
Hello, in response to your question, I think you should pay attention to the quality of the product when you buy a pool mosaic at the beginning.
Because the pool mosaic has high requirements for the material, it is required that the bricks laid in the pool will not crack due to gentle impact, nor will they crack due to long-term immersion in water. So you should pay attention to the hardness of mosaic tiles when purchasing, not only the hardness should be good, but also a certain toughness! In this way, it will not be easy to break, and it will not crack after paving.
The pool mosaic is fired at a high temperature of 1200 degrees, with a high degree of porcelainization, strong hardness, and a layer of crystal glaze on the surface, which increases the flexibility of the pool mosaic. In addition, the porcelain ceramic mosaic will also absorb a small amount of water, making the ceramic mosaic more flexible.
-
Professional swimming pool tile manufacturer Shuangou Ceramics to answer for you:
1. Before construction, the firmness, verticality and flatness of the base surface should be confirmed.
2. After the mosaic is scraped on the base surface, the mosaic must be pasted on it within the drying time.
3. After the pool mosaic is pasted, when it needs to be adjusted due to dislocation, it must be adjusted within the adjustment time so as not to affect the strength.
Fourth, the excess Pumosaic Yi cement in the construction process should be removed before hardening.
5. Check the glue layer on the back of the mosaic in time to ensure that there is no hollowing phenomenon, otherwise the slurry should be replenished in time.
6. 24 hours after the construction is completed, you can step in or fill the joint.
7. This product is suitable for use in the environment of 5 35, and it is forbidden to add water to stir the dried glue for reuse.
8. When the temperature is low in winter, the indoor temperature can be appropriately increased, and if the outdoor construction is carried out, the construction should be carried out as far as possible when the temperature is high at noon to prevent freezing after construction.
-
a. Check the material: pay attention to the packaging, model, area, color and other data of the product. First, measure the amount of mosaic used, and then cut out the required number of pieces and bars according to the condition of the building.
b, Flatten the wall foundation: This step is to flatten the foundation of the wall, and the wall must be smooth and the same color.
c, stirring tile adhesive: first calculate the area of the building, in the calculation of the amount of neutral tile adhesive you use, the coverage area varies according to the specific situation of the project.
d.Laying the foundation: It is very important to plaster the foundation of the wall, and use a toothed scraper to plaster the wall with neutral adhesive and white cement to a flat level.
Lay a good base and ensure that the moderation is between 5 degrees Celsius and 39 degrees Celsius. The wall must be smooth and of the same color.
e.Paving: If the pool mosaic is made of net, it can be directly applied to the wall or ground that has been coated with a neutral adhesive to neatly pave the mosaic.
f.Ensure consistent spacing: the gap between the pool mosaic and the pool mosaic must determine the consistent spacing, which is a process that requires patience in the process of paving the mosaic, but it is a key part of the paving work, and poor paving may affect the overall effect.
g.Reinforcement: After each pool mosaic, it is necessary to knead it firmly with a caulking tool to ensure that each place is evenly compacted and fully bonded with the adhesive, and each mosaic paste must wait for its surface to dry and stabilize before proceeding to the next step.
h.Agitating caulk: Calculate the required floor area first, and then calculate the amount of caulk required. Slowly pour the caulk into the water and stir carefully until it is evenly sand-free.
i.Caulking: Use the caulking tool to batch the caulk on the mosaic and evenly apply it to the surface of the pool mosaic, the caulking tool should move diagonally, first from bottom to top, and then from top to bottom, to ensure that all the caulk can be completely filled and there is no excess residue, the mosaic gap must be filled all or it is easy to accumulate dust, which will make it difficult to clean in the future.
j.Cleaning: Approximately 1 hour after the caulk has dried.
k.Finally: you can wipe the mosaic with water as a daily cleaning, if you encounter stubborn stains in some cases, you can use a stone cleaner, but please note that you must use a lot of water to clean after cleaning.
-
Summary. 1., brush glue.
Mix the strong tile adhesive according to the proportion, and evenly apply the tile adhesive to the wall with a plastering knife, and the thickness of the glue is 2cm. The stirred mosaic binder glue is best used up within 2-3 hours.
2. Tile pasting.
After brushing the glue, align the mosaic according to the drawing, stick the mosaic tightly with a plastering knife or putty shovel, or use a flat thick wooden board to pad the surface of the mosaic, and beat it evenly with a rubber hammer to ensure that the paste is firm.
How to paste the mesh mosaic of the swimming pool.
1.Brush glue according to the proportion of mixed strong tile glue, with a plastering knife to evenly apply the tile glue on the wall, the thickness of the glue is 2cm is appropriate. It is best to use up the stirred wide and slow loss mosaic adhesive glue within 2-3 hours.
2. After the tile is brushed with glue, the mosaic is paved according to the drawing, and the mosaic is attached tightly with a plastering knife or putty shovel, or a flat thick wooden board is padd on the surface of the mosaic, and the rubber hammer is evenly beaten to ensure that the paste is firm.
3. Check the paving situation The gap between the bricks and the bricks must be determined as a uniform width and simple width, if there is a deviation, you can use a small ash shovel to adjust the ash joints, in addition to the paved mosaic to check and fill in the gaps, and fill the small pieces of the falling mosaic. After completion, sit on the bench for 2 to 4 hours, depending on the weather. 4. Hook After the moisture is moderately dried and has initial strength, you can start hooking, prepare the caulk, and apply the caulk to the mosaic gap with a plastering knife to ensure that all the ash seams can be completely filled and there is no excess residue.
Within 20-25 minutes after caulking, the caulk on the surface of the mosaic should be gently dried with a high-density sponge, and then the cement or adhesive should be evenly applied to the construction surface. Used at the bottom of the pool and around it, it should be brushed with a layer of waterproof glue on the finished basis to avoid water seepage.
So the bottom net needs to be opened.
No. Okay, thank you, I thought they made a mistake to remove that, he used cement paste to the wall and then directly pasted the bricks and then filled the joints, do you know this, do you need to apply cement paste to that net.
There's nothing wrong with that.
-
Summary. If we say that when laying mosaic in the pool, we should try to paste the mosaic tile with waterproof glue, so as to prevent it from falling off, and do not leave a gap when pasting.
If we say that when laying mosaic in the pool, we should try to paste the mosaic tiles with waterproof glue, so that the beam can prevent it from falling off, and there should be no gaps when the rubber mindfulness is pasted.
Pool mosaics are conventionally used with ceramic mosaics and glass mosaics. Swimming pool mosaic has high requirements for material, and the hardness of glass mosaic is enough, but the flexibility is not enough, so it is often easy to break. Ceramic mosaic is fired at a high temperature of 1200 degrees, with a high degree of porcelinization, strong hardness, and a layer of crystalline glaze on the surface, which increases the flexibility of pottery and branch porcelain mosaics.
Therefore, it is better to have a ceramic slippery mosaic sticker pool.
What kind of glue should I use to paste it?
-
Summary. Hello, I'm very happy for your question, when the pool mosaic is pasted, it is definitely not possible to choose the traditional cement to pave, so it is easy to fall off, you must choose a special pool tile adhesive to paste, recommend a better pool mosaic manufacturer Shuangou ceramics to you, their tile adhesive is dedicated to the swimming pool. Hope it helps.
Hello I am very happy that you are rushing to the beam of this problem, when the pool mosaic paste, it is definitely not possible to choose the traditional cement to pave, know that the spring is easy to be peeled off, you must choose a special pool tile adhesive to paste, recommend a better pool mosaic manufacturer Shuangou ceramics to you, their tile adhesive is dedicated to the swimming pool. Hope it helps.
Can you use tile mastic?
OK. House bathroom tile adhesive pool
Can caulking be done with wall tile glue?
OK. After a year or two, the white tile glue will not change color?
No, it won't.
I want to install a mirror for my own room, a long dressing mirror, because the frame is not good, so I want to glue the mirror directly to the wall, and then paste the glass mosaic on the side as a frame, I don't know if this is feasible, my home has been renovated, can it be processed directly like this? The mirror is so glued, can it be glued? The last time I looked at the swap space, I saw that I could directly coat the mosaic with something like latex or what kind of glue, and then it could be glued directly to the wall, how did I get it? >>>More
If you put it on, it won't fall off.
Depending on the degree of adhesive stickiness, there are the following removal methods: >>>More
When choosing fish belly white tiles in the bathroom, we should pay attention to the ground hollowing, paving scheme, horizontal positioning, waterproof measures, tile paving and tile joints. >>>More
Generally, the temperature of floor paving is best controlled at more than 10 degrees. In winter, the climate is relatively dry, so you should soak it in water before pasting the tiles, so that the tiles can absorb enough moisture before pasting, which can improve the tiles and cement mortar. >>>More