What is the best temperature to control for general floor paving?

Generally, the temperature of floor paving is best controlled at more than 10 degrees. In winter, the climate is relatively dry, so you should soak it in water before pasting the tiles, so that the tiles can absorb enough moisture before pasting, which can improve the tiles and cement mortar.

connectivity to reduce hollowing in the later stage.

Shedding and other problems. If you move the tiles from the outdoors to the indoors, it is best to let the tiles adapt to the indoor temperature before applying the tiles. After the construction of the tiles is completed, the joints should be hooked in time. Because it will be difficult to apply after drying, this can increase the firmness of the tiles.

1.In recent years, the electric heating floor has a place in the market, that is, it has the function of heating, and the practicality of the floor, and it can play the role of floor heating without planing or backfilling. After the floor is paved, it is necessary to brush a layer of floor paint, and polish and wax from time to time.

Because floors are often worn out, brushing floor paint and polishing and waxing can help protect the floor, prolong the life of the floor, and make it easier to clean. When laying the floor, it is generally used with ground nails, floor glue, and moisture-proof mats, and their advantages and disadvantages will affect the service life of the floor paving.

2.The flooring is stored at room temperature for two days before being laid and then covered with plastic film. Make sure the floor and floor are clean before installation.

If necessary, brush a thin layer of cement slurry before paving to remove stains from the floor and allow the cement to dry before paving. Avoid frequent movement and placing heavy objects on the floor to give the floor adhesive enough time to stick and allow the floor to dry naturally. If the humidity on our walls or floors is particularly high and there is always a layer of water, then it is actually impossible to apply tiles at this time.

3.Autumn temperatures are suitable, but one thing is that the wind is particularly strong, and in the case of high temperatures and strong winds, it will also cause the water to evaporate quickly. One of the most common cases of rapid evaporation of water is to cause hollowing, so when laying tiles in autumn, be sure to control the hollowing of tiles, otherwise it may cause the tiles to loosen and fall off.

The above is the answer to the question of how much is the best way to control the temperature of general floor paving.

Generally, when laying, the temperature should be kept at 15 17, so as to achieve the best cement firmness, and will not affect the laying speed of the floor, but also to achieve the best protection effect.

About 15 degrees, this temperature is relatively good, can be better laid, is good for the floor, can avoid some thermal expansion and contraction problems.

It is best to have a temperature above 10 degrees Celsius, so that there will be a good bonding efficiency. It should not be lower than 5 degrees.

How much pro does it take to lay the floor temperature of the plastic floor! Hello, I am happy to answer for you<> the temperature should be moderate when laying plastic flooring, and the ground temperature should not be lower than 15 degrees or the temperature is too high. Paving PVC floor glue must ensure a reasonable ambient temperature, generally required to keep the temperature at 20-35,; Below 15, be cautious in construction; Below 5 No construction is prohibited.

The relative humidity of the air is required to be between 20% and 75%, and PVC flooring should not be paved if it is greater than 75%. Different glue, different floors, different grounds, different environments, etc. - the glue drying time is envied and stared at differently - the professional quality of the pavement master, the accumulation of experience in cherry jujubes, the sense of responsibility, and the professionalism of the pavement master. The exhaust after PVC floor rubber paving needs to be timely, attentive, patient, hard, meticulous and comprehensive.

After PVC floor glue, it is generally required to press it again with at least 50 pressure rollers in about 2 hours; Special circumstances also require more effective measures. After PVC floor glue paving, it is generally required to be welded after 24 hours - welding is too early, and the floor at the welding site may arch upward. Cracks in the ground foundation can cause self-leveling bulging, which in turn will cause the floor to bulge.

Hope mine can help you <>

Do you have any other questions or questions that you would like to consult?

Hello, laying industrial flooring requires an indoor temperature of more than 15. This is because at temperatures below 15, the flooring material will become more fragile and prone to cracking, deformation and other problems, which will affect the service life and aesthetics of the floor. In addition, if the temperature is too low, the stickiness of the floor glue will also be reduced, resulting in a weak installation of the floor.

Therefore, before laying the floor, it is necessary to ensure that the indoor temperature reaches more than 15, and at the same time, it is also necessary to pay attention to the control of indoor humidity to avoid problems such as moisture and mildew on the floor. After laying the floor, it is also necessary to pay attention to indoor ventilation to ensure that the floor is dry and ventilated. In addition to temperature and humidity control, laying industrial floors also requires attention to the flatness and cleanliness of the floor.

The unevenness of the floor will affect the installation effect and service life of the floor, while the cleanliness of the floor will affect the aesthetics and hygiene of the floor. <>

The benzene board is about 20mm the pipe is about 20mm and the ground part has to be at least 20mm, otherwise the load bearing is not good, the floor is about 68mm in thickness according to 8mm, but in general, the benzene board is not used, unless it is necessary to use the first floor, if the insulation cotton is used as the insulation layer, the thickness should be at least about 55mm.

The standard thickness of floor heating floor is, laminate flooring is generally 6 8mm, three-layer parquet 8 9mm, as long as the environmentally friendly qualified laminate floor, can be used as floor heating floor, multi-layer parquet for floor heating is also good, the stability is better, the defect is thicker, and the density is relatively low, which will affect heat conductivity to a certain extent, but the comfort is better than that of laminate flooring.

In general, three-layer parquet and hardwood flooring are not recommended. The upper and lower layers of the three-layer parquet are the higher density wood of the same wood species, and the middle is pine, because the density of the middle layer is much smaller than the density of the upper and lower layers, the expansion coefficient of the low-density object after the moisture is greater than that of the high-density material, which is easy to cause the expansion of the middle layer of the three-layer parquet after being damp is greater than that of the upper and lower layers, resulting in floor cracking. Most solid wood floors are not suitable for floor heating flooring, and a small number of solid wood can be used as floor heating floors, however, limited by wood species, and some special process treatment must be done, the price is relatively high, and it is not suitable for ordinary families.

I have the most say and regret it.

The floor tiles in my living room, the wooden floor in the bedroom, when the floor heating is turned on, the bedroom is obviously much colder than the living room, at least 3 degrees. Touching the floor tiles with your hands is hot, while the wooden floor is lukewarm. Leave the bedroom door open every day to let in the warm air from the living room.

The wood floor does not transfer heat, we all know this, and the most important thing is that when the wooden floor is laid, there is a layer of "moisture-proof pearl cotton" underneath, which isolates the heat under this layer of cotton, which is simply the nemesis of floor heating.

So, don't use wooden floors for floor heating! Don't use wooden floors for underfloor heating! Don't use wooden floors for underfloor heating! Important words to say three times!

I didn't have any information to tell me, so I regret it!!

Don't say that wooden floors are cheap, think about it, in 2017, the ordinary ** in 4th-tier cities will be calculated: cement leveling fee 20 + wood floor 150 170.

The floor tile is 800 * 800 square meters, which is 26 yuan per piece, which is equivalent to 40 yuan per square + 30 brick laying labor 70 yuan.

You can compare the heat dissipation of the ground of two different materials, for example, in the following table, when the average water temperature of 300mm spacing is 30mm, the heat dissipation of the tile floor is 37% more than that of the wood floor; If the outside temperature is -10, then adding 37% of the heat will increase the room temperature from 15 to 24. Of course, because the heat dissipation will decrease as the room temperature increases, it will not actually increase that much:

Floor heating? Oh, the manufacturer is suspected of exaggeration.

The floor itself is less efficient at heat transfer than the floor tiles, and the room temperature is at least three to five degrees different.

How can you still use flooring for bathing, more floor tiles are used in homes, public places, or flooring can still be used for bathing? Oh, think for yourself.

Even if it is used for the aisle, doesn't the small basket carried by the bather drip water?

It also has advantages: it saves paving costs compared to floor tiles.

Right now. Many commercial houses have chosen geothermal heating. Geothermal heating cancels the heating pipes and radiators in the room, which is more conducive to the layout and beauty of the room, so this method is recognized and accepted by more and more people. How do you choose a geothermal floor?

Although the merchants claim that it can be used for geothermal heat. But in fact, according to experts, 55 of them cannot be used for heating systems, 25 can be used for underfloor heating, but the effect is not ideal, and only 20 are dedicated underfloor heating floors. Therefore, experts remind consumers to pay attention to some misleading statements, such as "the thicker the wooden floor, the better the feel", "the thicker the more insulated", the special geothermal floor has foam pads and aluminum foil on the back, and the packaging box is printed with "special for greenhouses" is the geothermal floor.

As everyone knows, these statements are unreasonable, they will only affect the heat dissipation on the ground.

Due to the particularity of geothermal heating, the requirements for the floor are very strict, therefore, in addition to meeting the conventional quality indicators, the geothermal floor must also meet the following four major requirements:

Good thermal conductivity and heat dissipation. Wood and bamboo are good natural materials, and there will inevitably be heat loss from the floor to the surface through the floor, which can be minimized by an ideal floor. Therefore, in order to reduce the loss of heat energy and reduce the cost of heating operation and maintenance, the floor heating floor must be "thin but not thick".

Choose from multi-layer solid wood, bamboo and laminate flooring with a board thickness of up to 8 mm and a maximum of 10 mm.

Dimensional stability should be good. The use environment of geothermal floor is complex, especially in the northern region, the ground has to withstand various moisture in the non-heating season, and the ground temperature has to rise suddenly during heating, and the wooden floor must bear the double change of "temperature" and "humidity". Therefore, geothermal flooring must be purchased with good stability, such as laminate flooring, multi-layer solid wood flooring, bamboo flooring, and other integrated composite flooring.

Good moisture and heat resistance. Adhesives should be used for integrated composite flooring, and the adhesives should meet the three major indicators of environmental protection, gluing strength, high temperature and high humidity aging. Especially for geothermal floors, it is necessary to go through high humidity resistance, low temperature resistance and other experiments, if ordinary adhesives are used, environmental protection indicators, moisture resistance, aging resistance, expansion rate, etc. can not meet the standard.

Therefore, it is very necessary for consumers to check the product report and inspection report of the merchant when purchasing.

Abrasion resistance should be long-lasting. Since the geothermal floor should be thin rather than thick, the composite surface layer is generally more than millimeters. The abrasion value of the main surface layer of paint is higher than that of traditional indicators.

For wood, it is recommended to use electricity and geothermal heat, and the high temperature can reach about 30 degrees Celsius at most, but 20-26 degrees Celsius is generally recommended.

Now in addition to the pure solid wood flooring, the rest are all suitable for geothermal paving It is recommended to buy brand flooring Don't buy real estate flooring The quality is too high*** It is recommended to use Rhine sunshine flooring.