How to repair styrofoam, styrofoam did not succeed with what can be salvaged back

1. In the meltingStyrofoamAdd molding water and stir vigorously, then add makeup remover water and stir to restore.

2. Add a piece of hard styrofoam to the melted styrofoam, and then rub vigorously to mix the two, and then you can see the styrofoam return to its original appearance.

3. Add a piece of clay to the melted styrofoam and mix, then stir well, and you can return to its original appearance.

Production method: 1. Prepare glue and glycerin.

Shaving foam or facial cleanser.

Foam, borax water.

2. First put glue and glycerin in the container, then add shaving foam or facial cleanser foam and stir, add some water when stirring, the amount of water is half of the glue;

3. Finally, add borax water, it should be noted here that borax water should be added in small quantities and many times when stirring, and it is taboo to add too much water when making styrofoam, which will make the styrofoam too thin, so that the styrofoam will not be able to pull the wire.

After foaming gelatinization, you can add some molding liquid or borax water appropriately. This method can effectively solve the problem of styrogelization. The following is a brief introduction to the production steps of homemade styrofoam:

First, prepare a cup or small bowl with some dish soap in it, add as much glue as you want to make, and then add some hand sanitizer.

Kiss! Hello, happy to answer your <>

The pro-styrofoam wheel has not succeeded in using the opening tung to burn what can be saved back The method is as follows: the first step: styrofoam does not foam, it is possible that less materials are added to help foaming in the production process, in this case, we can add some materials that can help foaming to the styrofoam, such as facial cleanser or bubble hand sanitizer and the like.

Step 2: In addition to the reason that the foaming material is less, it may also be because the foaming glue is too thin to foam because there is too much water in the styrofoam to make it impossible to foam. Hope mine can help you <>

Do you have any other questions?

What should I do if styrofoam is too sticky? Look how I saved with baking soda, no borax turned out to be worse.

Summary. Hello dear, <>

1. What to do if the styrofoam is hard and can become soft.

1. Add some detergent and shower gel into it, you can rub it by hand, or you can stir it slowly, it is relatively soft at first, and it can be formed after rubbing for a while, and it can also increase the foaming effect of styrofoam.

2. Adding glue directly can also make the foaming glue softer, but it is more sticky when rubbing.

3. You can stir with warm water, and then rub it by hand until it is formed.

How to fix styrofoam when it is hard.

Hello dear, <>

1. What to do if the styrofoam is hard can become soft 1. Add some detergent and shower gel into it, you can rub it by hand, or you can stir it slowly. 2. Adding glue directly can also make the foaming glue softer, but it is more sticky when rubbing. 3. You can stir with warm water, and then rub it with your hands until it is formed.

1. Add the foam made of toothpaste to the inside of the styrofoam, and then rub it to make it soft. When adding, it is necessary to pay attention to the prohibition of adding soda toothpaste, and it is not directly added to the stool, but to squeeze out the foam of the toothpaste first, and then add and stir it in an appropriate amount of steps, so that the effect will be better.

Add glue and glycerin inside the styrofoam, mix and mix to make it soft, which is actually a new styrofoam on the basis of the original, the effect is the best, but the implementation is not as simple as the first two methods, and the material cleaning and preparation are not very close to the people.

What to do without soda.

You can also use toothpaste, dish soap, and shower gel.

Add tung canopy to the styrofoam and add hand cream or cream to soften. First throw the hard styrofoam into the basin, add an appropriate amount of hand cream or cream to rub it, and then you can see the foaming loose wheel glue extended into a film, continue to knead, and when it becomes a brush, it means that the softening is successful.

What is the method of making the styrofoam softer1, put the hardened styrofoam on the fire and heat, it will become soft after a while, but with this method, if it is not used for a long time, the styrofoam will still become hard, and repeated heating will affect the quality of the styrofoam. 2. Soaking the hardened styrofoam in the hot water orange car cover can also have the effect of softening the sail beat, but it is only temporarily soft and cannot last long.

Styrofoam tutorial:

Method. First, prepare a container and add an appropriate amount of divination glue to it. Then add a small amount of toothpaste and stir well. It should be noted that the amount of paste must be paid attention to, otherwise it will not be able to bubble in the later stage. Then add the pigment of your favorite color and stir well.

After stirring well, add an appropriate amount of borax water and stir to form. Then start to lather, pick it up when it bubbles and fold it several times. For all of the above steps, you can repeat the foaming three times.

Method. 2. First add a clay to the container, then add water to melt. Once it's melted, add the pigment of your favorite color.

After that, add your usual hand sanitizer and stir it well. Then add the foam and stir to mold, if not enough, add again. Keep stirring, and after stirring and molding, you can get started, so that the styrofoam is ready.

Styrofoam precautions:

Styrofoam is a common game entertainment toy, and the type of open stove and styrofoam playability is very high, can be very good to develop and design children's IQ, so children are more fond, but the general shopping malls sell styrofoam is made of borax, super glue and other substances are harmful.

Therefore, in the case of children playing, it will cause damage to children, and in general, children should control the baby's play time, and they must take care of the baby early, and they can not let the child put styrofoam into the mouth.