-
Windows is unable to access the system partition or boot volume during the boot process. It usually happens when it boots up for the first time after replacing the motherboard. This is mainly due to the fact that the IDE controllers of the new motherboard and the old motherboard use different chips.
Sometimes it can also be caused by viruses or hard drive damage.
Resolve the 0x0000007b of the stop error
1. Boot sector viruses usually cause this stop error. Use the latest version of anti-virus software to check.
Check your computer for viruses. If a virus is found, perform the necessary steps to remove it from your computer.
Fall. Refer to your antivirus software documentation to learn how to perform these steps.
2. Remove all newly installed hardware (RAM, adapters, hard drives, modems, etc.).
3. Check the Microsoft hardware compatibility list to make sure all hardware and drivers are compatible with.
Windows 2000 compatible.
4. If you are using a SCSI adapter, you can get the latest Windows from a hardware vendor
2000 driver, disable synchronization negotiation for the SCSI device, check if the SCSI chain is terminated, and check.
The SCSI IDs of these devices. If you're not sure how to perform these steps, you can refer to the documentation for those devices.
5. If you are using an IDE device, define the IDE port on the board as the only primary port. Check.
The IDE device is uniquely set by the master-slave. Remove all IDE devices except the hard drive. If you can't confirm such as.
To perform these steps, refer to the hardware documentation.
6. If the computer has been formatted with the NTFS file system, you can restart the computer and then set the computer in the .
Run the chkdsk f r command on the system partition. If the system cannot be started due to an error, then use life.
Order the console and run the chkdsk r command.
7. Run the chkdsk f command to determine if the file system is corrupted. If Windows 2000 doesn't.
You can run the chkdsk command to move the drive to a different computer running Windows 2000, and then.
Run the chkdsk command on the drive from this computer.
-
The hard drive has a bad sector. 100% of the re-drive system was installed
-
The computer cannot be turned on, and "stop:0 000007b" appearsSolution:
Restart the computer, press the shortcut key F2 or Del key to enter the BIOS startup item setting interface when the boot screen appears, move the cursor to "Advanced" through the left and right arrow keys on the keyboard, then press the up and down arrow keys to select "SATA Configuration", and press the Enter key to confirm.
A mode selection window will pop up, where we can select the "ahci" mode by moving the cursor up and down the arrow keys up, and then press the enter key to execute.
Press the F10 key to save the changed settings. When the computer restarts, we will find that the system no longer shows the blue screen error**0x000007b.
Most of the blue screen issues are caused by the hard drive mode in the BIOS settings not matching the current system.
How to troubleshoot the computer blue screen failure:
First, understand what happened to your computer and what it did before the blue screen occurred. If your computer has a blue screen after overclocking your CPU or memory, etc., then the blue screen failure is related to overclocking, as long as the frequency is restored to normal.
If the computer is opened abnormally when the optical drive is read and the blue screen is caused, the blue screen fault is caused by misoperation.
If a blue screen occurs when a computer is plugged in and unplugged from a device, the BSOD fault is related to the plugging and unplugging device, and it can be recovered by restarting the computer.
If a blue screen occurs when using a certain application software, the blue screen fault may be caused by this program software, and the fault can be eliminated by uninstalling the program software and reinstalling it. If it doesn't work, it may be that there is a bug in the program software itself and it cannot be used.
If the blue screen appears after the computer enters the system, there may be many reasons for the blue screen failure, and you need to eliminate it gradually. Use antivirus software to check and kill the virus first, and eliminate the blue screen fault caused by the virus, if you troubleshoot, it is the blue screen fault caused by the virus.
If it is still the case, restart the computer, then start the computer in "safe mode", exit the system after booting and then reboot to normal mode, if you rule it out, it is a blue screen fault caused by a system error.
If the fault is not troubleshooting, then use the backed up registry to restore the Windows registry to its normal state, and if it is troubleshooting, it is the blue screen failure caused by the Windows registry corruption.
-
Method. 1. The hard disk mode is set incorrectly, enter the BIOS to reset it.
1. Restart the computer and keep knocking on the boot hotkey to enter the BIOS, usually F2, ESC, and Del keys, you can try it. Enter the main BIOS interface, select Integrated Peripherals from the up and down arrow keys, and press Enter. (Different computer BIOS interfaces are different, and the setting method is basically the same).
2. Find the hard disk mode setting SATA configuration, and select the arrow key to press Enter. In the pop-up page, select the IDE compatibility mode and press Enter to confirm. Finally, press F10 to save and exit, and restart the computer.
Method 2: If the driver is installed incorrectly, enter safe mode and uninstall it.
1. Press F8 to select safe mode to enter when you boot up.
2. Enter the safe mode to uninstall the newly installed drivers, software programs, and it is best to check and kill viruses.
-
0*000000007b: Windows cannot access the system partition or boot volume during the boot process. It usually occurs when the motherboard is booted for the first time after the motherboard is replaced, mainly because the IDE controller of the new motherboard and the old motherboard use different chipsets.
Sometimes it can also be caused by viruses or hard drive damage. Solution: Generally, you only need to boot the computer with the installation disc and then perform a repair installation to solve the problem.
For viruses, you can use DOS antivirus software to detect and kill. If there's a problem with the hard drive itself, install it on another computer and use it"chkdsk /r"to check and fix disk errors.
-
Quote: Stop Error Number: 0x0000007b
Description: inaccessi-ble-boot-device
Common cause: Failure to initialize the IO system (usually the boot device or file system).
Workaround: Boot sector viruses usually cause this stop error. Use the latest version of anti-virus software to check for viruses on your computer.
If a virus is found, you must perform the necessary unsearchable removal from the computer, refer to the anti-virus software documentation to learn how to perform these steps.
Remove all newly installed hardware (RAM, adapters, modems, etc.).
Check the Microsoft hardware compatibility list to make sure all hardware and drivers are compatible with Windows.
If you are using an appropriate SCSI adapter, you can obtain the latest Windows drivers from the hardware vendor, disable synchronization negotiation for the SCSI device, check if the SCSI chain is terminated, and check the SCSI ID of the device, if you are not sure how to perform these steps, you can refer to the documentation for the hardware device.
If you are using an IDE device, define the IDE port on the board as the only primary port. Check the master-slave unique settings of the IDE device. Remove all IDE devices except the hard drive. If you are not sure how to do this, you can refer to the hardware documentation.
If your computer has been formatted with the NTFS file system, you can restart your computer and run the chkdsk fr command on the system partition. If the system cannot be started due to an error, then use the command console, and run the chkdsk r command.
Run the chkdsk f command to determine if the file system is corrupted. If Windows can't run the chkdsk command, move the drive to a different computer running Windows and run the chkdsk command on that drive from that computer.
-
It is usually the hardware that is in poor contact that causes more problems.
-
Reinstall the system and see if you can fix it.
-
The computer has a blue screen before it is turned on, how to unload things.
-
System problems, it is recommended to reinstall and try....
Sorry didn't see it clearly.
Just follow the steps below. >>>More
The system is poisoned and attacked.
Oh, this is caused by the landlord's abnormal shutdown.
This is called system hardware detection, and it should be the detection and sorting of the hard disk. >>>More
The error that occurs when prompting "Try to run C: Windows System32 ,NVSastartup" is because after the NVIDIA driver is installed, there are several startup items, and the startup item calls this file, but the file is gone, and it cannot be found. That's why I prompted this. >>>More
I want to ask you, is your computer the kind that crashes as soon as you turn it on? If so, there are two reasons, first, the motherboard northbridge chip is damaged, this problem can not be repaired, only to replace the new motherboard, second, there are bad sectors on the hard disk, when the location of the boot file is read, because there are bad sectors on the hard disk, it causes a crash. Depending on the severity of the hard disk, if it is not too serious, it can be repaired, and the maintenance fee is about 50 yuan.