How can the seam of the trousers be ironed with a garment steamer?

Usually the garment steamer will have a trouser clamp as an accessory. Buckle the trouser clamp to the ironing brush head, press down with a wrench side by side, so that the interface between the trouser clamp and the ironing brush head is opened, clamp the trouser seam, and slowly drag the ironing brush head from top to bottom, and a straight trouser line can be ironed out.

Specific steps: Step 1: First align the four middle seams of the pants (one trouser leg has two middle seams), and then align the four trouser legs;

Step 2: Use the clamp on the garment steamer to clamp the two ends of the trouser cuffs respectively; Then, after the pants naturally sag, clip the waistband of the pants respectively with clips (the waistband can be folded and shaped as needed).

Step 3: Fill the garment steamer water box with tap water (the water consumption can be based on the needs of ironing), then turn on and off the power switch, and wait for the hot air to come out of the garment steaming port;

Step 4: Hold about 20 cm in one hand.

The size of the plastic board (wood, cardboard can be), close to the back of the pants, the other hand holds the garment steamer ironing head, so that the air outlet is facing the pants that need to be ironed, you can iron up and down, left and right, and at the same time hold the plastic plate with the other hand and move up and down, left and right at the same time, until the folds are ironed flat.

The garment steamer will have a trouser seam clip as an accessory, and the trouser seam clip can be used to iron the trouser seam, and the specific operation is as follows:

1. First of all, prepare the garment steamer, pants, clips, etc.

2. Then, assemble the clamp sewing of the trouser press and the garment steamer head.

3. There is a buckle, which is very easy to install, look at the installed renderings.

4. After installation, clamp the pants with a seam clip.

6. Grab the trouser leg with the help of the other hand and slide it up and down, so that the seam of the trousers can be ironed.

7. This is done, look at the effect, the seam of the trousers is very conforming.

Step 1: Adjust the steam of the ironing garment steamer to continuous ironing, that is, the position of the first gear in front of the pulse steam. You can debug the steam.

Step 2: Put the ironing board down. Let's turn the inside of the legs of our pants upside down, lay them flat on the ironing board, press the steam switch, and the steam will come out and you can iron along the surface of the pants!

Step 3: Iron the inside well, and in turn, turn the pants on the outside up, and iron the trouser line that is needed, which is what we call the pants seam.

Step 4: I iron the middle part of the bottom plate of the nozzle against the corresponding line when I iron the trouser line, and the effect is much better!

Step 5: Iron the line, pick it up and see if it is what you want, if not, you can steam it flattened, repeat it again, after ironing to achieve the line you want, turn off the steam, use the dry ironing function to shape, the effect of this line can last for a long time.

Fold the pants according to the trouser line, clamp them in, and turn on the ironing.

OK. The garment steamer can iron the pants, but it should be ironed with the trouser clamp. The steps are as follows:

1. Fold your pants.

2. Use the special clip for hanging pants to clamp and hang it on the hook of the garment steamer 3. Clamp it with the trouser line splint and pull it down from top to bottom.

In addition, there is a special separate trouser cleat, and the nozzle can be used.

Garment steamer, also called hanging iron, vertical iron, is a machine that can hang ironing clothes and fabrics. The garment steamer continuously touches the clothes and fabrics through the boiling hot water steam generated inside, so as to achieve the purpose of softening the fiber tissue of the clothes and fabrics, and flattens the clothes and fabrics through the actions of "pulling", "pressing" and "spraying", so that the clothes and fabrics are as good as new.

The garment steamer can iron the pants, the steam of the garment steamer is large, and the ironed clothes and pants will not shine, especially the casual pants are more suitable for ironing with the garment steamer. In contrast, trousers are a little worse, because the middle seam of trousers cannot be ironed with a garment steamer, and can only be ironed when placed flat on the cutting board.

It should be ironed with a trouser clip.

Fold the pants, use the special clip for hanging the pants to hang on the hook of the garment steamer, and then use the trouser line splint to clamp and pull it from top to bottom.

That's how I get hot, but I use a garment steamer from Domain Bridge. There is a special separate trouser splint nozzle, I think this hot pants is the best, and other brands of trouser clips are a sleeve like a brush, which cannot be ironed at all.

OK.

Warm up first. Hang up your pants and you're ready to iron.

Ironing can be ironed, but the effect is not very good, because all pants, as well as the cuffs, buttons, and shoulders of the clothes need to be ironed before they can be ironed, and some brands can only be ironed. The HG I bought at home comes with an ironing board, and I heard that this is still their patent, so I don't know the specifics. However, their board is very stable and easy to use, like the collar, shoulders, cuffs, buttons, and pants of clothes, the ironing effect is obvious, and it is really convenient to use the ironing board.

I think the garment steamer should be summed up like this.

The first point of ironing pants is to iron them flat.

The principle of the garment steamer is to continuously contact the fabric through high-temperature steam, penetrate the fabric fiber tissue, soften the fabric fiber, and make the fabric smooth and smooth through the action of "pulling" and "pressing", and restore the natural state of the fabric. When ironing pants with a garment steamer, it is best to have a trouser rack rod to fix the pants, Huaguang's ironing machines have this design, which is fully functional and affordable, and can well ensure the smoothness of the trouser hem. When ironing, pay attention to ironing the trouser pockets, iron the trouser pockets, reverse the trouser pants, and iron the inner trouser pocket.

Some pants are worn for a long time, and the knee of the pants will bulge, which is difficult to iron. When ironing, iron the back half of the pants first, straighten the back half of the pants with your hands, stretch out the wrinkles and then heat until the back half of the pants returns to its natural state. Then iron the front half of the pants.

When ironing, many pants have bulges in front of the knees, and if the pants are straightened, the front half will be wrinkled. At this time, you should first iron from the upper and lower parts of the pants, and the iron should be gently placed on the pants first, and the steam switch should be pressed to make the wrinkled parts naturally retract under the heat of the iron. The same method is applied to the knee area, when the big bulge becomes a small bulge, continue to use the above method, and so on, you can all return to the original shape, and finally iron the whole pants again.

An important point in ironing pants is to iron out the trouser line.

The trouser line is the essence of a pair of pants, especially for trousers! Iron the pants, be stylish, there are two trouser seams on each side of the trouser leg, align them, and then make them flat Don't let there be wrinkles in the middle, when ironing, first low temperature and constant ironing, remember to wipe it with cold water after low temperature and constant ironing. It has a cold harvesting effect.

Or use a trouser clip to iron the trouser seam back and forth, and you can also iron out a beautiful trouser seam line.

Iron your pants with a garment steamer, remember the above two points, and you're good to go!

I think if you want to iron your pants better, you can try placing trouser clips on the garment steamer steam nozzle, so that the ironed clothes are more stylish and smooth. I use the Philips garment steamer myself, and the pleat clip is very practical, and the ironing pants is more stylish!

If you iron the pants, I personally think that the ironing machine is easier to use, he will have the effect of squeezing down, the pants are easy to form and easy to come out, Huaguang their ironing machine is very good, there are two modes of dry ironing and steam ironing, which is very easy to use.

Some netizens have made it very clear, and I will add a hint a little:

Check the accessory bag and manual, there is an accessory called "trouser clamp", you can install it on the steam nozzle, clamp the trouser leg to iron, you can iron the middle line on the trouser leg.

Ironing pants personally think that the machine of the HG family is more easy to use, he will have the effect of squeezing down, the pants are easy to form and easy to get out of the line, Huaguang has several garment steamers in their house have two modes of dry ironing and steam ironing, which is very easy to use.

Some garment steamers have special crossbars and trouser clips for hanging pants or use their own hangers to hang pants and hang hangers on hooks There are places for general design, Huaguang. The art of steam.

Some garment steamers have special crossbars and trouser clips for hanging trousers, or hang trousers on their own hangers.

Hang the hanger on the hook.

The general design has a place to place, Huaguang. The art of steam.