What causes toilet suction to become smaller?

1. The pipe is clogged and the drain pipe of the toilet is blocked, but not all of them are blocked, and only a small amount of water can flow. This way, things won't be washed away, which will lead to a reduction in the flushing speed. If the flush rate is low, the water flow rate slows down, and the flushing force of the toilet bowl will naturally decrease.

In this case, we need to clean the pipes of the toilet, and if we use a wrench, the effect is not obvious enough. It is best to use a pipe unclogger and, if necessary, replace the trap of the drain. 2. The sealing ring is damaged, whether it is a flush toilet or a siphon toilet, when flushing, there is actually a suction cup inside the toilet, and the dirt in the toilet is sucked away by using the suction power of the suction cup.

A necessary condition for water absorption is to maintain a good seal in the toilet bowl and sewer. After a large amount of water is flushed into the toilet, the pressure in the drain is lower and a suction force is created. Toilet seals are key to keeping toilets and sewers sealed.

If the seal is aged or damaged, the pressure inside and outside the pipe will tend to equalize, and then the suction will naturally be small. If the seal is damaged, you need to find a professional repairer to repair it, and it will involve the disassembly of the toilet. If not handled properly, it can lead to the toilet, causing the bottom to leak.

3. Another factor that affects the flushing intensity of the toilet is the amount of water, the greater the amount of water discharged in a short time, the greater the pumping intensity, which is also the reason why we can't feel the suction of the toilet when urinating. If the water in the toilet is damaged and cannot be fully opened, it will affect the effectiveness of the drain, resulting in insufficient flushing force and need to be replaced in time. There are still many cases where the toilet water parts are broken, and we can buy and replace them ourselves, which is still very simple to operate.

The toilet suction may be caused by a leaking toilet pipe, or a clogged sewer pipe, or the water level is not enough, and a smaller inlet valve may also cause the toilet suction to become smaller.

Caused by leaking toilet pipes; Caused by clogged sewer pipes; The water level is not enough, and the inlet valve is smaller, etc., may be the cause of the toilet suction.

1. Pipeline blockage.

The most obvious reason for the decrease in the suction power of the toilet bowl is that the drainage pipe is blocked, and the pipe, which was originally only the thickness of a fist, has become as thick as a few fingers, and the water will naturally not be able to drain smoothly and quickly, which is manifested in the fact that the suction power of the toilet has become smaller.

The first way is to use a pipe uncrusher. This is the most commonly used pipe dredging tool, ** is not high, after buying it back, it is directly rotated along the toilet mouth and put it in, and the debris in the toilet pipe is clamped out through the rotation between the springs.

The second method is with a pipe unclogging agent. The principle of pipeline dredging agent is to heat up after encountering water, and use the heat to dissolve the debris and oil on the pipeline. **A little more expensive than a pipe unclog, but also the easiest way to unclog a pipe.

Second, the sealing ring is damaged.

If the seal is damaged, causing the toilet suction to become smaller, the best way is to replace the seal, but this also means that the toilet should be removed and reinstalled, and it is recommended to find a maintenance worker to deal with it.

3. Toilet water parts are damaged.

If the toilet water parts are damaged, it is relatively simple to replace them, directly according to the size and specifications of the toilet water parts to find the water parts to buy from the water parts business, and after buying them, remove the old water parts and replace them with new ones.

What is the reason why the flush of the toilet becomes smaller, just twist this small mechanism and easily solve the troubles!

If the original impulse is normal, but now it is smaller, the general reason is that the pipe diameter has become thinner due to the garbage stained on the inner wall of the flushing pipeline or the solid waste has blocked the pipeline. In the case of iron pipes, it may be the cause of rust on the inner wall and the thinning of the pipe diameter.

Remove it for clearance, clean it thoroughly, and it should bring the impulse back to normal.

If it is an iron pipe, it needs to be replaced.

Views are for reference.

After a long time, the toilet was dirty, flushed with medicated water and air pumps.

Adjust the capacity of the water tank, or if it is blocked, it needs to be cleaned up.

The reasons why the toilet bowl suction becomes less are as follows:

1. The damage of the sealing ring causes the air to enter the toilet bowl, and the pressure will definitely become smaller, and the suction power will also become smaller.

2. When the toilet is displaced, part of the drain will be easily blocked, and the water flow will become smaller when flushing down.

3. The suction power of the toilet suction pipe becomes smaller due to air leakage, and a new suction pipe needs to be replaced at this time.

How to take care of the toilet

1. Do not place in direct sunlight, near direct heat sources or exposed to oil smoke, otherwise it will cause discoloration.

2. Do not place hard objects and heavy objects, such as water tank covers, flower pots, water bridge land buckets, pots, etc., otherwise it will scratch the surface or cause cracking.

3. The cover plate and seat ring should be cleaned with a soft cloth, and strong acid, strong carbon and decontamination powder should not be used to clean with volatilizers, thinners or other chemicals, otherwise the surface will be corroded. Do not use sharp objects such as steel wire silver brushes and blades to clean.

4. When the cover plate is installed in the no water tank or low water tank, people should not lean back, otherwise it will cause breaking.

5. The cover plate should be opened and closed lightly to avoid direct collision with the water tank and leave marks and affect the appearance; may cause breakage.

6. Pay attention to the products using metal seat hinges (metal screws), and do not let the acidic and alkaline solvent adhere to the product, otherwise it is easy to rust.

The reasons for the decrease in the suction power of the toilet are: insufficient water level in the water tank, clogged toilet, fouling inside the toilet, aging of the toilet seal, and clogged sewers.

1. The water level of the water tank is insufficient.

The suction power of the toilet bowl is achieved by relying on the water pressure in the tank, and if the water level in the tank is insufficient, then it will affect the suction power of the toilet. Therefore, if you find that the suction power of the toilet has become smaller, you can check the history to see if the water level of the water tank is sufficient.

2. The toilet is clogged.

If the toilet is clogged, then it will affect the suction power of the toilet. There are many reasons for a clogged toilet, such as too many paper wheels, foreign objects entering, and so on. When the toilet is clogged, you can use the toilet pass or toilet bowl to solve it.

3. Scaling inside the toilet.

The fouling inside the toilet bowl is also one of the reasons for the toilet bowl to become less suction. There are many reasons for the fouling inside the toilet, such as poor water quality, too long use, and so on. When the inside of the toilet bowl is fouled, it can be cleaned with a toilet bowl cleaner or a professional cleaning service.

4. The toilet seal is aging.

Toilet seals are an important part that connects toilets and sewers, and if the seals are aged, it will cause the toilet to have less suction. When the toilet seal is aging, it can be solved by replacing the seal.

5. Sewer blockage.

The blockage of the lower Laqi waterway is also one of the reasons for the small suction power of the toilet. There are many reasons for clogged sewers, such as grease, foreign bodies, etc. When the sewer is clogged, you can use a pipe unclogging agent or a professional cleaning service to solve the problem.

<>1. If it is a siphon toilet, the collapse of the empty energy is that there is a blockage in the siphon bend of the toilet, and you can dredge it with a leather puff or find a master to repair it. 2. The sealing ring of the toilet will be damaged after a long time of use, which will lead to the reduction of the suction power of the toilet. After replacing the sealing ring of the toilet bowl in time, it can be waterproof with glass glue.

3. The side handle chain of the side press or side panel toilet is too long. After opening the toilet lid, move the blind ring inside a little back.

We can often see toilets in our daily life, but there will be various problems after using them for a long time, so what should I do if the suction power of the toilet becomes smaller?

1. What should I do if the suction power of the toilet becomes smaller?

1. If it is a siphon-style toilet, it may be that the siphon is blocked, and you can dredge it yourself with a leather pistol or contact a professional to overhaul it.

2. If the toilet is used for a long time, it will also lead to the problem of damage to the sealing ring, so as to reduce its suction.

3. The side handle chain of the Ma Yuan trillion barrel is too long, after opening the toilet lid, move the buckle inside to the rear.

Second, what are the precautions when using the toilet?

1. The lid must be closed when flushing, otherwise the cyclone inside will bring dirt to the air, thereby polluting the sanitary ware and having a bad impact on people's health.

2. The most polluted place is the toilet seat, because it is in contact with people for a long time, so it must be paid special attention to when cleaning, and scrub with diluted disinfectant every few days to ensure that it is always clean.

3. The dirty things in the toilet bowl should be cleaned up in time, otherwise it is easy to have stubborn stains.

4. Try not to place a paper basket next to the toilet, which will lead to the increase of bacteria and pollute the indoor air.

I summarize: the above is the reason and solution for the toilet suction to become smaller, from the above article we can see that we must first figure out the specific problem, and then choose the appropriate solution according to him, so as to ensure that the problem is solved while avoiding unnecessary consumption, saving a lot of money and time, I hope to help everyone.

1. The siphon effect is greatly reduced due to the deviation of the pit position, and the flushing effect is affected.

Solution: In this case, you can only remove the toilet bowl and check whether there is any deviation, so you should test the water in time when installing it and check it.

2. The material is inferior, and some manufacturers blindly reduce costs, resulting in cracking when they are injection molding, and the toilet leaks and has hidden cracks, resulting in the inability to form a water seal and a peculiar smell.

Workaround: Contact your local repairer.