Is there a template for the hot work certificate, and what are the three types of hot work certifica

Appendix 1 Hot Work Permit (Grade) Section.

Record number of the applicant unit.

The location and content of the ignition device.

Ignition Man Special job category and number.

Fire Supervisor Burn Supervisor Employee Species.

Detection time, sampling point, analysis result, analysis person.

The time of fire is from YYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYY

Serial No. Main Safety Measures for Fire Signature of the confirmer.

1. Clean the inside of the hot equipment, and the steam purge or water washing is qualified to meet the hot conditions.

2. Disconnect all pipelines connected to the hot equipment, and add blind plates ( ) blocks.

3. The wells, floor drains, trenches, cable trenches, etc. around the ignition point (minimum radius of 15 meters) have been cleared of flammable materials, and have been isolated by means of covering, sand spreading, and water sealing.

4. The oil tanks in the same cofferdam and fire spacing within the ignition point in the tank area shall not be dehydrated.

5. Anti-spark splashing measures should be taken for high-altitude operations.

6. Remove flammable materials around the ignition point.

7. The welding circuit should be connected to the weldment, and the wire should not pass through the sewer well or be connected with other equipment.

8. The distance between acetylene cylinders (no lying down), oxygen cylinders and the fire source shall not be less than 10 meters.

9. The site is equipped with fire-fighting steam belts, fire extinguishers, shovels, and asbestos cloths.

10 Other Security Measures:

Completion acceptance: Signature of relevant personnel: year, month, date and hour.

Hot workThere are three types of tickets: first-class fire, second-level fire, and special fire.

To put it simply, it is easy to understand: the construction site needs to use fire, the construction site needs to have relevant approval documents to operate, and the relevant departments have issued a certificate before construction, so it is called the fire certificate only in the state.

1. Definition of fire:

1. Hot work: welding and cutting operations in the fire prohibition area and the use of blowtorches and electric drills in flammable and explosive places.

Grinding wheels, etc., are used for temporary work that may generate flames, sparks, and hot surfaces.

2. Flammable and explosive places: the places where the items are produced and stored conform to the areas classified as Class A and B in the fire hazard category in GB50016-2014.

1. Responsible department: It mainly refers to the department of temporary operations such as maintenance, renovation and construction carried out in the company, such as equipment management.

Department, Production Technology Department, etc. Responsible for the application for the return of the fire, the handling of the "Safety Work Permit", the cleaning and monitoring of the fire site, etc.; When the contractor in charge starts a fire in the company's area, the preliminary examination of the "Safety Work Permit" and the supervision of the hot work status.

2. Contractor: responsible for the application of hot work, the handling of the "Safety Operation Permit", the cleaning and supervision of the hot site, etc.; Responsible for cooperating with and implementing the safety precautions, rectification and preventive measures proposed by the responsible department and the management department.

The fire permit should be handled at the local fire department.

The fire certificate refers to a permit issued by the relevant departments when the construction site is engaged in hot work. The fire permit shall be handled by the person in charge of the project of the unit where the fire is located. The safety measures shall be proposed by the unit next to the fire, the construction unit shall be responsible for the implementation of the construction aspect, and the production unit shall make arrangements for the production aspect.

The precautions for the use of the fire permit are as follows:

1. If the fire is started in the hidden part, it should be repeatedly checked within half an hour after the operation is completed to prevent smoldering;

2. In case of windy weather above level 5 in the open air, stop the welding operation;

3. It is not allowed to cross the fire with flammable and explosive types of work such as paint and spray painting at the same time;

4. It is strictly forbidden to start a fire in a dangerous place with flammable gas or dust;

5. There shall be no combustibles around the fire scene and within the range of sparks splashing and falling under the high-altitude fire;

6. Oxygen cylinders and acetylene cylinders have pressure gauges, and the distance between the two bottles shall not be less than 5 meters, and the open flame operation shall be greater than 10 meters, and they shall be used upright;

7. There is a caretaker at the fire scene to supervise the whole process, and be equipped with fire extinguishers and buckets in accordance with the requirements of the security department;

8. If there are holes in the ground at the fire site, they must be inspected and blocked or blocked before the fire can be started;

9. The validity period of the fire permit is valid within the approval time of the application on the same day; Otherwise, it will be regarded as an unlicensed and illegal operation.

Legal basis

Article 15 of the Fire Protection Law of the People's Republic of China.

Public gathering places are put into use, and fire safety inspections before opening are to be managed by notification and commitment. Before the public gathering place is put into use or opened, the construction unit or the user unit shall apply for fire safety inspection to the local people's fire rescue agency at or above the county level where the place is located, make a commitment that the place meets the fire protection technical standards and management regulations, submit the required materials, and be responsible for the authenticity of its commitments and materials.

The fire and rescue agency will review the materials submitted by the applicant; Where the application materials are complete and conform to the legally-prescribed form, permission shall be given. Fire and rescue agencies shall, in accordance with the technical standards and management provisions for fire protection, promptly conduct inspections of public gathering places that have made commitments.

If the applicant chooses not to use the method of notification and commitment, the fire and rescue agency shall, within 10 working days from the date of accepting the application, inspect the site in accordance with the fire protection technical standards and management regulations. If it meets the fire safety requirements after inspection, it shall be permitted.

Public gathering places must not be put into use or open for business without the permission of the fire and rescue organization. The specific measures for fire safety inspection shall be formulated by the emergency management department.

Legal Analysis: Fill in the Specification for the Fire Safety Work Certificate Application Unit xx Workshop Department Applicant Workshop Safety Officer or Supervisor Operation Certificate Number Hot Work Level Level Level 1 Fire (Fire Grade is divided into Special, Level 1, Class 2, Operation on the Pipe Gallery is Class 1 Fire, Holiday Fire Operation Upgrade Pipe Fire Cutting Using Gas Welding Cutting, Electric Welding Welding Fire Location and Location In all work permits, the description of the operation location or location must be accurate and unique, and the specific operation point must be determined according to the description. Such as:

The top platform of the debenzenification tower Ignition time The person in charge of the ignition operation Li Moumou The ignition person Operator a, the operator The ignition analysis time 2016 10 2016 10 2016 10 The name of the analysis point The surrounding environment of the platform (the ignition analysis point should be clear and specific, and indicate whether it is environmental analysis or in-equipment analysis.

Legal basis: Measures of the People's Republic of China for the Administration of Industry Standards

Article 1 In order to strengthen the management of industry standards and ensure the coordination and unification of industry standards, these measures are formulated in accordance with the provisions of the Standardization Law of the People's Republic of China and the Regulations on the Implementation of the Standardization Law of the People's Republic of China.

The second industry standard is a standard formulated for the technical requirements that need to be unified within a certain industry in the country without a national standard. Industry standards shall not contradict relevant national standards. Relevant industry standards should be coordinated and unified, and should not be duplicated.

Industry standards shall be abolished after the implementation of the corresponding national standards.

Article 3 The following technical requirements need to be unified within the industry, and industry standards (including the production of standard samples) can be formulated

1) Technical terms, symbols, codes (including **), file formats, drawing methods and other common technical languages;

2) The varieties, specifications, performance parameters, quality and quantity indicators, test methods, and safety and health requirements of industrial and agricultural products;

3) Design, production, inspection, packaging, storage, transportation, use, maintenance methods of industrial and agricultural products, as well as safety and health requirements in the process of production, storage and transportation of sails;

4) Technical requirements for general parts;

5) Product structure elements and interchange and coordination requirements;

6) Technical requirements and methods for the survey, planning, design, construction and acceptance of engineering construction rolling fiber hail;

7) Technical requirements for information, energy, resources, transportation, and their management technology.