The electric oven tripped after 50 minutes of use, what s going on

The trip indicates that there is leakage or excessive current.

Generally, it is the leakage of the heating pipe, and the number meter is 20 megabytes, and the number is displayed to indicate the leakage.

It's best to go to the seller to have a look, and if necessary, take it to the seller for repair.

1. Pay attention to cleaning when using the electric oven for the first time.

Wipe the inside and outside of the oven with a clean, damp cloth to remove some dust. Then you can use the oven to bake at high temperature for a while, and sometimes white smoke may come out, which is normal. After baking, pay attention to ventilation and heat dissipation.

2. After cleaning, the electric oven can be used normally.

Before baking any food, it needs to be preheated to the specified temperature to meet the baking time on the recipe. It takes about 10 minutes to preheat the oven, and if the oven is preheated and left empty for too long, it may also affect the life of the oven.

3. The oven that is heating should avoid burns.

In addition to the high temperature inside, the shell as well as the glass door are also hot, so be careful when opening or closing the oven door to avoid being burned by the glass door. When placing the baking tray in or taking it out of the oven, be sure to use the handle, and strictly prohibit direct contact with the baking tray or the baked food with your hands. Never allow your hands to touch the heater or other parts of the furnace chamber to avoid burns.

4. When the oven is in use, the temperature should be adjusted first.

When the oven is in use, the temperature should be adjusted first, the upper and lower heat, the upper and lower heat, and then the time knob should be twisted clockwise (do not twist counterclockwise), and the power indicator light will light up at this time, which proves that the oven is in working condition. In the process of use, if we set 30 minutes to bake food, but through observation, the food will be baked in 20 minutes, then we should not twist the time knob counterclockwise at this time, please adjust the fire gear in the middle of the three knobs to turn off, which can prolong the service life of the machine. This is different from the use of microwave ovens, which can be reversed.

5. It should be cleaned after cooling after each use.

It should be noted that when cleaning the door and furnace shell, it should be wiped with a dry cloth and should not be cleaned with water. If you encounter dirt that is difficult to remove, you can gently wipe it off with dish soap. Other accessories of the electric oven such as baking trays, grills, etc. can be washed with water.

6. The oven must be placed in a ventilated place.

Don't lean too close to the wall to make it easier to dissipate heat. And it is best not to place the oven near the water source, because the overall temperature of the oven is very high when working, and if it touches the water, it will cause a temperature difference.

7. When the oven is working, do not stay in front of the oven for a long time.

Do not stay in front of the oven for long periods of time.

If you notice a crack in the glass door of the oven, stop using it immediately.

Is the trip faulty trip or stop heating? Precise temperature control is to stop before the set temperature is reached, otherwise the temperature rushes over, which is normal and does not need to be ignored.

Hello, thank you for your attention 1, the oven trip may be caused by the simultaneous use of a variety of household appliances resulting in excessive current, to avoid the simultaneous use of a variety of household appliances. 2. The oven tripping may be that the total terminal connection is not tight, there is a heating phenomenon, or there is a problem with the performance of the switch, you need to check whether the terminal connection of the main opening is normal, tighten the fixing screw or change to a new switch. 3. The oven tripping may be a problem with the fixing or insulation of the heating wire in the oven, when the temperature reaches a certain value, there is leakage or short circuit, it is necessary to check whether the heating wire in the oven and the fixing screw of the heating pipe are normal, whether the internal line insulation is damaged, whether there is a foreign object on the line, it is necessary to tighten the fixing screw, strengthen the insulation, remove the foreign matter, and replace it as soon as possible if the heating wire is deformed.

Hello, I can't hear your voice because of the system.

Questions. The heating of the two pipes on the top does not trip, if the heating of the four pipes of the same inch trips, what's the matter, master.

The current is too big, the voltage is too big, and your line can't carry it.

If the heating tube is damp, disconnect the ground wire and heat it for half an hour before connecting it back. If the oven is short circuited by moisture. It is advisable to open the door of the oven and dry it or send it for repair.

, the circuit failure at home, the aging of the circuit, or the existence of other large-capacity electrical appliances, if used with the oven, will cause overload and trip. If the voltage is too high because of the high power of the oven, you can try to replace the air opening or socket. or send it for repair.

If you are not sure whether it is an oven problem, you can connect the oven to other circuits to try, and also replace a leakage protector. If the oven is leaking, the leakage switch is not working at all. It is recommended to check whether the insulation of the line is normal first.

If it is a leakage of the heating pipe, it is not possible to check and repair it, and consider replacing it.

Notes:

1. Operate according to the requirements of the instruction manual.

2. The electric oven should be placed in a flat and stable place, and ensure reliable contact with the grounding bolts, and use 250V, 10A single-phase three-core socket to match the power plug, and the glass window and socket should be kept clean during use.

3. The heat and heating speed are different, and it is most important to grasp the temperature and time of baked food when using. There is a heat dissipation phenomenon near the door of the furnace, and the food should be turned over when baking to make it evenly heated.

4. Take food to operate with power failure, and use the handle fork to clamp the baking tray to prevent touching the heating element from scalding your fingers.

5. Keep the inner cavity wall clean, bake the food, if there are seasonings, oil stains and other things in the inner cavity, you can use a towel to moisten the soapy water and gently wipe the inner cavity wall of the oven until it is clean, and discharge moisture from the furnace door, do not rinse the inner cavity of the oven with water to prevent the electrical components from getting wet.

6. When not in use, turn the three transfer switches of power, temperature control and timing to the shutdown position and put them in a dry, ventilated and clean place.

Take Midea's pt2531 multi-functional electric oven as an example, the oven has been vacant for a long time, and it will trip as soon as it is used, which is generally caused by the humidity of the oven, you can directly put the oven in a dry and ventilated place to dry for a while, or you can connect the oven to the socket of the air conditioner and start heating for a while to solve the problem.

If the above methods cannot solve the problem, it is recommended to contact the after-sales service or professionals for relevant testing in time.

Precautions for use of the oven: When using the oven to bake food, the user needs to preheat the operation, generally about 10 minutes of preheating, if the oven is preheated and baked for too long, it may also affect the service life of the oven.

After using the oven, the user also needs to clean it, but it should be noted that before cleaning the oven, the plug should be unplugged and wait for it to cool down completely before cleaning.

Data expansion: An oven is a sealed appliance used to bake food or dry products, which is divided into household appliances and industrial ovens. A household oven can be used to process some pasta.

Industrial oven is a kind of equipment used to dry products in industry, with electricity and gas, also known as ovens, drying ovens, etc.

Causes: 1. The sensor pins are loose or in poor contact.

Solution: Adjust the prong position to service the sensor.

2. The sensor is damaged and the resistance value is wrong.

Solution: Replace the sensor.

3. The control circuit board is faulty, and the control signal cannot be received and sent.

Solution: Replace the control circuit board.