The Baojun 730 brakes can t be pressed, and the Baojun 730 rebounds when the brakes are pressed

Baojun 730 brake can not be stepped on is definitely the problem of the booster pump, if it is not able to step on the case of flame-off, it is normal, because the flame-out vacuum booster pump does not work, if you can't step on it while driving, it may be caused by the vacuum booster pump leakage or fuse damage.

The brakes of Baojun 730 may not be stepped on, it is possible that there is gas in the brake oil, and it is recommended to exhaust the air well.

Hello, this situation is generally caused by air in the brake tube, you can see if the brake fluid is missing, and then drain the air and try again.

For naturally aspirated engines, the vacuum comes from the throttling effect of the intake pipe throttle; For turbocharged engines, the vacuum comes from the vacuum pump, and the vacuum level required for brake assistance is required, so if you can't step on it, it may be that the vacuum degree is gone.

Hello, you see if the car is stalled, or the brake fluid is not enough, if it is all right, it is a problem with the vacuum booster pump.

Hello, it is recommended to check whether it is caused by the failure of the power pump of the brake, and check the brake pads.

Hello, this situation may be the cause of the problem with the booster pump, which needs to be carefully checked.

Hello, this should be the brake emptying is not done well, or the brake cylinder is a problem, you can check it specifically.

Hello, like this case, it is recommended that you check whether the brake cylinder is enough in the sudden braking, and whether the brake fluid is sufficient?

Summary. Hello, Car Master Mechanic is here to serve you. Attentive, careful, attentive, for you to answer the car fault problems, for you to find the corresponding problem solutions and maintenance methods.

We will provide you with a satisfactory answer to your questions, I hope this service can help you, if it is helpful to you, I look forward to your praise and attention. I wish you a good year of the tiger and good luck, Hello, friend, according to the questions you said, to answer your boring phenomenon, it is your vehicle on the ABS work. The anti-slip system intervenes, resulting in this when the brakes are applied.

For this solution, you need to clean your tire ABS sensor and gear signal words. It is caused by the abnormal signal transmission caused by dirty sensors or dirty things on the signal teeth, and this brake signal is anti-slip work. Wash it and you're good to go.

Hello, happy to answer your questions.

Hello, Car Master Mechanic is here to serve you. Attentive, careful, attentive, for you to answer the car fault problems, for you to find the corresponding problem solutions and maintenance methods. We will provide you with answers to your questions about this satisfactory travel, I hope this service can help you, if it helps you, look forward to your praise and attention.

I wish you a good year of the tiger and good luck, Hello, friend, according to the questions you said, to answer your boring phenomenon, it is your vehicle on the ABS work. The anti-slip system intervenes, resulting in this when the brakes are applied. If you want to call a solution, you need to clean your tire ABS sensor and gear signal words.

It is caused by the dirt of the sensor or the dirty thing on the signal tooth, which leads to abnormal signal transmission, and the brake signal is anti-slip work. Wash it and you're good to go.

Summary. Hello dear for your question. Dear, the reasons why the brakes of Baojun 730 are not sensitive are as follows, 1. If the brakes of the car are not sensitive, first of all, we can try to tighten the brakes first.

You can first use a wrench to loosen the screws of the brake line, and then use pliers to pull the brake line back a little to make the brake line tighter, and then tighten the fixing screws, so that the brakes can be tightened. 2. The brake is not sensitive, it is likely that the steel wire of the brake line is overused, at this time we should adjust the wire pipe at the connection between the brake handle and the brake line, and the brake can be used normally.

Hello dear for your question. Dear, the reasons why the Baojun 730 brakes are not sensitive are as follows, 1. If the car brakes are not sensitive, first of all, we can try to tighten the imitation silver calendar brakes. You can first use a wrench to loosen the screws of the brake line, and then use pliers to pull the brake line back a little to make the brake line tighter, and then tighten the fixing screws, so that the brakes can be tightened.

2. The brake is not sensitive, it is likely that the steel wire of the brake line is overused, and we should adjust the wire pipe at the junction of the handle of the brake and the brake line at this time, and the brake can be used normally.

Pro, it may also be because the car is too badly worn, if it is a serious wear and tear, then it needs to be replaced.

Pro, the slow braking response treatment method 1, put the car in low gear, pull the handbrake to change the original high-end bright sensitive hall into a low gear, Jingyin according to the surrounding environment to control the speed and direction of the car. It is worth noting that the tightness and speed of the handbrake should also be moderate, not too tight and not too loose. 2. If the brakes fail when going downhill, the driver should immediately look for obstacles on the side of the road, such as stones or trees, etc., which can create some resistance for the car and make the car stop.

In our daily driving process, we must check whether there is a hidden danger of failure of the brake and repair it in time.

Summary. If you can't press the brakes now, it is recommended that you still press hard. It is possible that your vehicle has turned off and you have applied the brakes again, so this will cause your brake vacuum booster to not work and will not be able to step on it.

In this case, you only need to press the brake pedal hard, and then you can start normally, if you really can't press it, then you can lie on your brake pedal position and see that there is a switch above, you can rotate the switch directly counterclockwise to remove it, and then you can start it again. After activation, you can put this switch back in again, so that it can be restored.

The Baojun 730 can't step on the brakes, and it can't be started with one button.

Hello, this question can give you a perfect reply, wait for me to sort out the information, I'm typing, 2-3 minutes, don't finish.

If you can't press the brakes now, it is recommended that you still press hard. It is possible that your vehicle has turned off and you have applied the brakes again, so this will cause your brake vacuum booster to not work and will not be able to step on it. In this case, you only need to press the brake pedal hard, and then you can start normally, if you really can't step on it, then you can lie on your brake pedal position and see that there is a switch above the bend before the noise, you can directly rotate the switch counterclockwise to remove it, and then you can start it again.

After the bumper is activated, you can bury the switch back and reinstall it, so that it can be restored.

No switch seen. Just above the pedals.

What shape. Not yet.

Can't you remove this switch?

Yes. Can you light up the meter now?

The indicator disc light flashes.

Then you're losing battery. Is it that the meter will go out when you start it, and the one-button start switch will light up again when you release it.

Start the dashboard flash, and wait for the dashboard to light up, a lot of confusion.

Yes, you are losing power in the battery, just find someone else to come and give you electricity.

If I can help you, please give me a thumbs up Thank you!

If you step on the brake pedal, you can hear the "click" sound between the gearbox and the gear handle, the main reason for the sound may be the electronic linkage between the braking system and the automatic transmission gearbox.

If you step on the brake pedal when you step on the brake, you can hear the "click" sound between the gearbox and the gear handle, the main reason for the sound may be the electronic linkage between the braking system and the automatic gearbox.

It may be normal to have a rattling sound when stepping on the brakes (such as new car running-in, ABS work, etc.), but after all, the brake is an important part of driving safety, and it is best to go to a professional repair shop for maintenance.

Causes of the rattling sound when applying the brakes:

1. Excessive wear of brake discs and brake pads Brake discs and brake pads are high consumables for seepage keys, and the two parts of the brakes must be rubbed every time, and there will naturally be loss in the long run. Usually the replacement cycle of brake pads is 6-80,000 km, while the brake disc is 10-120,000 km.

2. If there is a problem with the assembly of brake pads, if the brake pads are installed in the opposite direction or the model is not right, then there will be abnormal noise, you can reinstall the brake pads, and when the car mainly installs the brake pads, it is necessary to go to a professional auto repair shop to carry out the operation, especially in the roadside stalls to replace the owners of the brake pads, you should pay more attention to this.

3. Other possible reasons are that the failure of calipers, brake discs and brake pads may produce this sound. If the sound is continuous, first check whether there is drag, poor caliper reset will cause the disc to rub against the disc for a long time, and under certain conditions, it will make abnormal noise. In addition, if there are foreign objects on the brake pads and brake discs, it can also cause strange noises.

Photo by Q&A) @2019