How to disassemble a CPU fan, how to disassemble a CPU fan

Updated on number 2024-08-14
8 answers
  1. Anonymous users2024-02-16

    1.Shut down and disconnect the power supply, remove the fan power cord from the CPU fan header on the motherboard, and if the fan has an RGB cable, remove the RGB cable from the CPU cooler and the RGB connector on the motherboard as well.

    2.Gently pull the cam upwards.

    3.Unlock the heatsink from the mounting lugs of the motherboard slot.

    There is a fixing clip on the cam rod side.

    4.Gently twist the CPU fan back and forth from side to side, slowly separating the heatsink from the CPU top cover.

    5.Carefully lift the CPU cooler, and the CPU should remain in the slot after removing the fan.

  2. Anonymous users2024-02-15

    The way to remove the fan of the computer CPU is to untie the buttons on both sides of the fan with a screwdriver, and then use a small Phillips screwdriver to remove the button rod, and remove the dust after removal. The details are as follows:

    1. There is a button on both sides of the fan, take a flathead screwdriver to pick up the four buttons of the bracket and take them away, as shown in the figure below.

    2. You can pick up the fan directly when the button is taken away, be careful, don't damage the motherboard too hard.

    3. Then take a small Phillips screwdriver to remove the lever of the buckle, as shown in the figure below.

    4. After removing it, you can decompose the fan, and then take a cloth or screwdriver to clean up the dust.

    5. The latter one can be rinsed with water, and then dried with a hair dryer.

    6. After all the cleaning is completed, you can reinstall the fan, and you can reinstall it or install a new fan directly from step 4.

    Precautions: 1. Be sure to cut off the power supply to avoid electric shock.

    2. Pay attention to safety, protect yourself when using tools, and don't get hurt.

    If you want to remove the fan, you have to involve the CPU

    Because part of the fan is connected to the CPU through silicone.

    The silica gel in the middle is a heat transfer medium.

    As for how to remove the fan.

    Generally, fans have a bracket that is directly attached to the motherboard by screws.

    Then there is also a bracket on the CPU fan.

    The two brackets can be used to secure the fan with a snap.

    It is recommended that you still do not dismantle it.

    Don't disassemble it and put it on.

    After dismantling, you have to re-apply silicone to the CPU and fan base.

    If you turn on the computer in the summer, you don't have this loud phenomenon.

    Now it's cold.

    That's quite normal.

    Generally, it will be relieved after a period of operation.

  3. Anonymous users2024-02-14

    Here's how:1. Remove the CPU fan graphics card: Prepare a screwdriver, and remove the CPU fan from the computer to remove the graphics card.

    2. Remove the fixed graphics card: Use a screwdriver to remove the screws that fix the graphics card.

    3. Unplug the cable connected to the graphics card: Unplug the cable connected to the graphics card.

    4. Dismantle the buckle: The buckle on one side of the CPU fan is pressed and lifted, and the buckle on one side is removed.

  4. Anonymous users2024-02-13

    1.Shut down and disconnect the power supply, remove the fan power cord from the CPU fan header on the motherboard, and if the fan has an RGB cable, remove the RGB cable from the CPU cooler and the RGB connector on the motherboard as well.

    3.Unlock the heatsink from the mounting lugs of the motherboard slot, which has a clamp on the cam rod side.

    4.Gently twist the CPU fan back and forth from side to side, slowly separating the heatsink from the CPU top cover.

    5.Carefully lift the CPU cooler, and the CPU should remain in the slot after removing the fan.

  5. Anonymous users2024-02-12

    The steps to remove the CPU fan are as follows:

    1. When disassembling the CPU radiator, first pull up the metal fastener to the other end.

    2. Finally, slowly push out the buckle at one end of the metal buckle with both hands, and if the buckle is tighter than the slippery one, you can also use a screwdriver and other tools.

    3. When one end of the buckle is opened, the release of the other end of the buckle is much easier, as long as the buckle is slowly pushed out by hand.

    4. When the buckles at both ends are all opened, you can slowly remove the CPU radiator of the letter hole, one of the points that need to be noted here is that because the heat dissipation silicone grease may stick the CPU and the bottom metal of the radiator together, so when removing the CPU radiator, it must be removed vertically to avoid bending the fragile pins of the CPU.

    5. The installation method is the same, which is to fix the hook and then hook up the iron bars on both sides.

  6. Anonymous users2024-02-11

    The steps to remove the CPU fan with age are as follows:

    Tools: Lenovo Yangtian M4000Q, screwdriver.

    1. Find the two screws behind the computer host that fix the side cover of the main chassis, use a Phillips screwdriver to loosen them, and pull them out at the same time.

    2. After the main chassis is opened, you can see the computer motherboard, and then find the four bolts that hold the CPU fan. The bolts are positioned around the CPU fan, and use a screwdriver to remove the fixing bolts at the corners of the CPU cooling fan.

    3. After removing the four fixed bolts, you also need to pull the bolts in the four corners of the CPU fan.

    4. After that, follow the CPU fan to find the power cable connected to the motherboard, and cut off the power supply.

    5. After unplugging the power cord of the CPU fan, you can use your hand to hold the grip on the periphery of the CPU fan, and at the same time lift up to pull the CPU fan out, and then you can complete all the disassembly work.

  7. Anonymous users2024-02-10

    1.Shut down and disconnect the power supply, remove the fan power cord from the CPU fan connector on the motherboard, and if the fan has an RGB cable, remove the RGB cable from the CPU cooler and the RGB connector on the motherboard.

    3.Unlock the fins from the mounting lugs of the kingpin slots, there is a clamp on the cam rod side.

    4.Gently twist the CPU fan back and forth from side to side, slowly separating the heatsink from the CPU top cover.

    5.Carefully lift the CPU cooler and remove the fan, the CPU should remain in the socket slot.

  8. Anonymous users2024-02-09

    The following describes how to remove the CPU fan.

    1. First of all, unplug the power cord between the fan and the motherboard.

    2. Use a screwdriver to unscrew the corner screws that hold the CPU fan in place.

    3. Note that it is best to unscrew the screws diagonally to avoid the fan bouncing. After unscrewing the 4 screws, you can remove the fan directly by hand, and pay attention not to damage the hardware.

Related questions
15 answers2024-08-14

It is not possible to maintain 15 degrees with a 600-800 fan. You should have turned on the AMD power-saving function, because you are not using the computer now, 5000+ will automatically reduce the frequency if you don't have it, so the temperature you see is unreal, when you use the computer, it will return to the frequency of its own work, and the temperature will go up a lot at this time.

4 answers2024-08-14

The 5000+ is an AM2 interface, and you can use an AM2 interface CPU fan. >>>More

17 answers2024-08-14

It's not aging, it's running out of oil.

You can go to the computer repair and get some oil to wipe it yourself. >>>More

6 answers2024-08-14

The speed is automatically adjusted, don't modify it yourself, otherwise the CPU will burn! >>>More

6 answers2024-08-14

The computer always makes a strange noise when it is turned on, and it will be normal when it is restarted, this situation repeats itself if this is the dust that accumulates on the CPU fan, which affects the normal rotation of the fan, so it produces noise, and it is highly recommended to replace the fan. The fan of the P4 processor is more difficult to remove the original one, and before replacing the CPU, you first need to remove the fan before replacing it with a new CPU fan. Step 1: >>>More