-
1.Shut down and disconnect the power supply, remove the fan power cord from the CPU fan header on the motherboard, and if the fan has an RGB cable, remove the RGB cable from the CPU cooler and the RGB connector on the motherboard as well.
3.Unlock the heatsink from the mounting lugs of the motherboard slot, which has a clamp on the cam rod side.
4.Gently twist the CPU fan back and forth from side to side, slowly separating the heatsink from the CPU top cover.
5.Carefully lift the CPU cooler, and the CPU should remain in the slot after removing the fan.
-
The CPU fan will be in the fan blade after a long time.
As well as the accumulation of dust in the bushing, it will produce relatively large noise when rotating, so it is necessary to dust the fan at this time, so how to remove the desktop computer CPU fan? Below I will bring you the method of disassembling the ** computer CPU fan.
How to remove the desktop computer CPU fanFirst, open the side cover of the case.
At this point, you can clearly see where the fan is located.
Note: When dismantling the fan, it is recommended to touch the metal objects first to dissipate the static electricity from the body, so as not to get on the computer due to static electricity.
Second, disconnect the fan from the motherboard's power cable.
Third, there is a snap device between the CPU and the fan, move it away, and put the fan and heatsink.
Take it off together. There are also buckles that look like this.
It's up to the computer to decide whether to move or hang out.
In this way, the fan and heatsink on the computer have come down, and under normal circumstances, the fan and the heatsink will be connected together with screws or buckles and other things, and it is good to remove the screws and buckles.
1.How to remove the computer CPU fan.
2.How to remove a desktop fan.
3.How to remove the CPU fan.
4.How to disassemble the CPU fan**.
5.How to disassemble and assemble the CPU fan.
6.How to disassemble the desktop computer CPU.
-
The steps to remove the CPU fan are as follows:
1. First open the computer main chassis, find the two screws on the back of the main chassis that fix the side cover of the main chassis, screw them out with a Phillips screwdriver, and then pull them out directly.
2. After opening the main chassis, you can see the motherboard of the computer, and then find the four bolts that hold the CPU fan in place. The location is around the CPU fan. You can use a flathead screwdriver to remove the fixing bolts on the corners of the CPU cooling fan.
3. After removing the four fixing bolts, tighten the bolts at the four corners of the fan at the same time. Note that they are only pulled out slightly, not pulled out.
4. At this point, you can follow the CPU cooling fan to find the power cord connected to the motherboard, and then directly unplug the power cord upwards.
5. After unplugging the power cord of the CPU cooling fan, you can grasp the outer wraparound handle of the CPU cooling fan with your hands. Also, use the lifting method to remove the CPU cooling fan.
-
Here's how:Tool required: Screwdriver.
2. Pull up the bolts at the four corners of the fan with your hands.
3. Remove the power cord connected between the fan and the motherboard.
4. After completing the above steps, you can remove the cooling fan on the CPU of the computer host by hand, and the disassembly of the hot fan is completed.
-
1. There is a button on both sides of the fan, if you press it down and don't untie it, take a flathead screwdriver to pick up the four buttons of the bracket and take them away, as shown in the figure below.
2. You can pick up the fan directly when the button is taken away, be careful, don't damage the motherboard too hard.
3. Then take a small Phillips screwdriver to remove the lever of the buckle, as shown in the figure below.
4. After removing it, you can shout or trillion to decompose the fan, and then take a cloth or screwdriver to clean up the dust.
5. The latter one can be rinsed with water, and then dried with a hair dryer.
6. After all the cleaning is completed, you can reinstall the fan, and you can reinstall it or directly install a new fan from the 4th step of Zheng Ren. If it needs to be replaced, there is no need to clean the fan, and the new fan is still installed according to the original disassembly method.
Emmet electric fan dismantling and washing: Remove the Emmet electric fan first and then clean the fan. >>>More
To remove the graphics card from your computer, the steps are as follows: >>>More
First open the engine compartment, find the inlet pipe of the warm air tank, the return pipe, and remove it with pliers. >>>More
Tools Required: Pliers.
Screwdriver. 1. First, loosen the middle part of the mop handle with your hands. >>>More
Use a small word change cone to pry the small gap on the side of the panel, and open it with a prie. >>>More