How to install the screws connecting the floor fan lifting rod and the above piece

Updated on technology 2024-08-15
4 answers
  1. Anonymous users2024-02-16

    Put the lifting rod over the upper end of the fixed rod, clamp it with clamping screws, then put the decorative sleeve on the fixed rod, and the spring is sleeved in the fixed rod, install it in the middle of the base, tighten the strong screws, and complete the assembly of the base and the column.

    There is a knob on the floor fan rod to adjust the height and low, and after unscrewing, press down the rod to adjust the height.

    Floor fans can usually only be used on the ground and occupy a certain area. Fan.

    It can promote air circulation, and the temperature decreases slowly and is not easy to get sick. Fan.

    The wind can be adjusted at will, there are natural wind, sleeping wind, strong wind, etc.

    The wind speed of the electric fan should not be too large, so that the human body has an adaptation process. The indoor wind speed is best controlled in meters and seconds, especially in the room with better ventilation and in the place where there is too much wind, the wind speed of the electric fan should not be too large, the electric fan should not be blowing in front of people, blowing directly, the wind evil is easy to invade the body, especially when the body is weak or sweating, it is best to let the fan blow towards a corner.

    Precautions: Don't blow directional wind, try to choose one that can swing your head when buying an electric fan, so that the body can be winded smaller, you won't feel too cold, the temperature of the whole body is uniform, and you are not easy to get sick.

    Don't keep blowing when you are asleep, when you fall asleep, your body's basic energy is reduced to the lowest level, your immunity is reduced, and you are prone to illness.

    Don't blow for a long time, you can blow for about an hour when you feel hot, the temperature of the human body will drop with the evaporation of sweat for a long time, which is easy to cause colds.

    Colds and other physical discomforts.

    The above content reference: Encyclopedia - Floor Fan.

  2. Anonymous users2024-02-15

    Assembly Instructions 1The assembly of the chassis and the column, the lifting rod will pass the power cord through the large hole of the chassis and buckle the bottom of the column into the chassis, tighten the connector with a triangular nut to dock the connecting head with the lifting pipe, and fix it with a nut 2The rear grille nut is used for the assembly of the fan body part, the rear grille is fixed on the motor front cover of the machine head, the protective sleeve of the motor shaft is taken out, the fan blade is sleeved into the motor shaft, the quasi-positioning pin of the motor shaft is sleeved to the root, and the fan blade nut is rotated counterclockwise to buckle the fan blade fixed adjustment wrap directly below the front grille trademark, the wrapper is put into the front grille to adjust the front grille cover to keep the front mesh cover product horizontal, and the rear grille is inserted into the card slot 3

    The product assembly aligns the upper end of the lifting rod with the lower end of the control panel, and then tightens the fixing nut.

  3. Anonymous users2024-02-14

    The installation steps for household floor fans are as follows:

    1. Open the package and check whether the main parts and accessories are complete according to the packing list of the items.

    2. Combine the column and chassis to form a canopy. Insert the lower end of the lead column into the fan chassis (note that there is a socket setting), and tighten the column and chassis with bending screws.

    <>3. Unscrew the two fixing screws on the axis of the motor, the net harness and the leaf cai, and vacate the screw.

    <>4. Install the rear net along the axis of the motor, and tighten it clockwise with the net harness.

    5. Insert the fan blade into the axis of the motor, and push the back of the fan blade into the shaft bolt to the end to achieve a complete fit.

    <>6. Lock Ye Cai into the motor shaft in a counterclockwise direction and tighten it.

    7. The front net and the back net are close to each other, and the outside is fixed with a net clip. If the net clamp can't cover the front and rear nets, you can send the net clamp screws first, find the right position and then tighten it again.

    <>8. Power on the test machine, the power light is on, the fan rotates normally, and the floor fan is assembled.

  4. Anonymous users2024-02-13

    How to install a floor fan.

    1. Before installing the Midea floor fan, you need to prepare the installation tool screwdriver.

    2. Take out the column pipe and base of the floor fan, insert the column pipe into the installation hole in the base, and tighten the nut at the bottom of the floor after installation.

    3. Fix and tighten the lifting rod from the base pipe, if the lifting rod is inside the column, you need to pull out the lifting rod now, and then fix it, so that the base of the beautiful floor fan is installed.

    4. Insert the mounting hole of the main head of the floor fan into the stuck groove of the round tube, and then tighten the fixing screw of the main head with a screwdriver.

    Midea floor fan installation method.

    5. After the main engine head is installed, load the grille into the main engine head, and tighten the lock nut of the grille.

    6. After that, the fan blade of the Midea floor fan is loaded into the motor shaft, and the lock nut of the fan is tightened after it is installed in place, and the lock nut of the fan blade should be loosened in the clockwise direction.

    7. After the fan blade is installed, the mesh ring needs to be put into the rear grille, and then the front grille cover, and then fixed with the screwdriver in the yellow circle. Such a beautiful floor fan is even installed.

    Midea floor fan maintenance method.

    After buying a Midea floor fan, it also needs to be well maintained, so as to improve the service life of the fan, now let's take a look at the maintenance method of the Midea floor fan:

    1. The Midea floor fan should be placed smoothly when in use, and there should be no obstacles within the range of the floor fan shaking head, and the power cord should be prevented from tripping over people while placing the power cord.

    2. When using the timing switch of Midea floor fan, the timing switch should be rotated in the clockwise direction, not counterclockwise, to avoid damaging the timer.

    3. When placing the electric fan, it should be placed in a moisture-proof, sun-proof and dust-proof place, and when it is not used, it should be placed in a ventilated and dry place.

    4. Midea floor fans should add lubricating oil to the fan regularly, and the part of the fan shaking head needs to be cleaned every three years, and the lubricating oil in the gearbox should be replaced at the same time.

    5. When the Midea electric fan emits a strange sound, burnt smell or smoke during use, it should be turned off immediately and repaired.

Related questions
7 answers2024-08-15

Floor fan installation operation method:

1. Clarify the role and location of components. >>>More

19 answers2024-08-15

Well, this depends on whether it is serious, if it is serious, you have to get it to the after-sales service center, if it is not serious, you can say that the screws are loose, and then for example, there are some small problems like this fan, these can try to get it.

10 answers2024-08-15

This may be a problem with the switch, the inside is not in good contact, or some slow response will occur. >>>More

21 answers2024-08-15

The fire department entered the community to fight the fire and was blocked by the lifting pole, and the people of the property were there at the time, but because the lifting pole was broken, the fire was not timely. This is the responsibility of the property.

7 answers2024-08-15

It is a mechanism that transmits torque through worm gear deceleration and converts it into linear motion by the lead screw. The mechanism can realize the revocation of power self-locking in any position, and its main features are "safe and reliable" and "small power and large thrust". >>>More