How to start without turning off the ignition, how to start without going out

Start without turning off: the left foot should step on the clutch to the end, hang to the first gear, release the handbrake, should slowly lift the clutch, find the semi-linkage point, remember whether the linkage point is high or short, loosen the clutch when the car is slightly shaken is the linkage point, and then fill the accelerator when the car moves. Start-up stalling generally occurs in manual transmission cars, mainly because the clutch and throttle control are not done well.

It should be noted that the clutch linkage point of each car is different, so when driving for the first time, you should slowly lift the clutch to find the semi-linkage point, remember whether the linkage point is high or short, and the linkage point is the linkage point when the clutch car shakes slightly.

When the car is refueled, it is generally stepped on the accelerator in the semi-linkage situation, too early there will be an engine roar and stall, and there will be a stall after stepping on it, many novices do not start with the accelerator, just slowly loosen the clutch, and then step on the accelerator, which is also an important reason for the slow start, the clutch and the fuel pedal should be carried out at the same time, the novice starts with a big throttle, because the clutch is not released to the linkage point or too slow, the car should release the clutch at a uniform speed.

The trick to starting without going out.

How to get started: 1When getting on the bus, the seat should be adjusted, and the thighs and calves can be flexed and extended freely. This is very critical, if you don't sit well, you can't operate the car well.

2.Step on the clutch, the left foot should step on the clutch to the end, otherwise there is a sound of teeth in the gear, or the gear can not be hung up, which is easy to cause damage to the gears of the gear.

3.Hang gear, hang to 1st gear, many novices hang gear particularly hard, this is not advisable, should be gentle, according to the trajectory to hang to the corresponding gear. It is not possible to start in 2nd gear. The gear distribution of each car is different, please follow the gear lever instructions to hang in.

4.Releasing the handbrake, also known as the parking brake, novices often forget this, resulting in a particularly large probability of stalling, which should be kept in mind.

5.Loose clutch, the clutch linkage point of each car is different, so the first time you drive the car, you should slowly lift the clutch, find the semi-linkage point, remember whether the linkage point is high or short, and the clutch car is slightly shaken when the clutch is the linkage point. Once you have mastered the linkage point of the car, you should quickly lift your left foot to the linkage point when starting.

6.Fuel pedal, many novices start without throttle, just slowly loosen the clutch, and then step on the accelerator, which is also an important reason for the slow start of the ignition, loosen the clutch and the accelerator should be carried out at the same time, the novice start throttle is very big, because the clutch is not loosened to the linkage point or too slow. When the car moves, the clutch should be released at a constant speed.

When the semi-linkage is fed, keep the speed at 1500-2000 rpm, loosen the clutch, if you are not uphill, you don't need to step on the brakes, go uphill with the handbrake with more practice, and you can find a throttle speed that you are used to after a long time. Master the semi-linkage oil feeding, and the engine will not be extinguished at the start. Hope it helps, hope.

First of all, you need to pay attention to the steps when starting the vehicle. Press the brake first, then the clutch, and hang 1st gear. Then slowly lift the clutch pedal on your left foot.

When you lift it up to a position ready for early width, you will feel a little noise from the engine, accompanied by the body shaking, indicating that you have reached the clutch point. Now release the brake pedal and the vehicle will not back down. Then lightly step on the oil and open the door, and the vehicle can start smoothly.

There are three ways to start without turning off:1Start in neutral first, then quickly press the clutch, put the gear in 1st gear, and then slowly release the clutch, and feel the release to a certain position The car starts to move forward.

After the vehicle is moving forward, press and hold the clutch for two to three seconds, press the accelerator lightly, and slowly release the clutch at the same time, so that the start is relatively smooth. In the same way, shift the gear to 2nd gear and clutch it with one foot. 3.

The most important thing is to feel the point where the vehicle moves forward when the clutch is released. As long as you find this point, every time you shift to this point, step on the accelerator, and then release the clutch. Basically, the vehicle will be more stable.

The above is the method of starting the vehicle and starting without turning off, you need to pay attention to the skills of each step in order to drive the vehicle more securely.

The method of never turning off the engine at the beginning is: 1. The first task after hanging up the first gear is to give oil, step on the accelerator to 1500 to 2,000 rpm, and stabilize the right foot; 2. When slowly lifting the clutch to the semi-linkage point, step back a little, and at the same time quickly release the handbrake; 3. At the same time as releasing the handbrake, if you find that the car is about to slip back, relax the clutch of the left foot, adjust the throttle to maintain 1500 to 2,000 rpm, and most cars will start.

The method of never turning off the engine at the start is: 1. The first task after hanging up the first gear is to give oil, step on the accelerator to 1500 to 2,000 rpm, and stabilize the right foot; 2. When slowly lifting the clutch to the semi-linkage point, step back a little, and at the same time quickly release the handbrake; 3. At the same time as releasing the handbrake, if you find that the car is about to slip back, relax the clutch of the left foot, adjust the throttle to maintain 1500 to 2,000 rpm, and most cars will start. Here's the trick to never starting out:

1. After hanging the first gear, the first task is to feed the oil, step on the accelerator to 1500 to 2,000 rpm, and the right foot is stable;

2. When slowly lifting the clutch to the semi-linkage point, step back a little, and at the same time quickly release the handbrake;

3. At the same time as releasing the handbrake, if you find that the car is about to slip back, relax the clutch of the left foot and adjust the throttle to maintain 1500 to 2,000 rpm, and most cars will start.

There are several reasons why the ramp starts to stall:

1. Loosening the handbrake and lifting the clutch are not unified;

2. The throttle is not enough, and the oil separation is not well coordinated;

3. When the clutch reaches the semi-linkage point, the handbrake is slow, which may also affect the flameout.

Photo by Pacific Automobile Network Q&A).

When the clutch is released at the start, when the car starts to shake and move forward, the left foot holds the clutch firmly and does not let go again, and then completely releases the clutch after moving a few meters. No matter what time you start, as long as you follow the essentials, you will never turn off. You can start on flat ground without stepping on the accelerator, and you can practice normal starting by releasing the clutch.

It's normal to start by stepping on the accelerator, starting a little faster, and there is no harm to the car. It is okay to step on the clutch when ignition, there is no obvious difference. The main purpose of stepping on the clutch first and then igniting is to avoid sometimes forgetting to check the gear (hanging in the first gear after stopping), and the car suddenly rushes out due to the ignition caused by the ignition in the gear, which is dangerous.

It's a good habit to step on the clutch and ignite. Of course, the transmission should be hung in neutral before ignition, which is the correct way to operate.

If it is caused by the flameout, then it is necessary to go to a regular larger gas station to add high-grade oil, such as using 97 (Beijing 95) oil, and also to clean the oil circuit thoroughly, including fuel injectors, throttle, fuel tanks, etc., in addition to regular maintenance is also crucial, to check whether the oil circuit and circuit are unimpeded.

What is flameout.

Definition: When the reactor is operating at a significant reaction rate, if the temperature of the feed inlet is lowered so that it reaches the lower limit of the polymorphic region, the reaction speed will suddenly drop sharply and the reaction will basically stop. This phenomenon is called extinguishment.

The corresponding inlet temperature is called the extinguishing point. It generally refers to the engine of the car.

There are two main reasons for the phenomenon of stalling, the first may be caused by the lack of driving skills that lead to the rush of driving at the start, and the use of substandard oil and other substandard engine supplies may cause the engine to malfunction. There may also be the wrong gear (which is not the case with normal drivers) or forgetting to release the parking brake.

In contrast, automatic transmission models are much less likely to stall at the start, and generally do not forget to release the brakes without stalling, but start smoothly.

When starting without turning off, you need to listen carefully to the sound of the accelerator when you step on the accelerator and slowly lift the clutch. During the lifting of the clutch, there are three sounds: "high", "calm", "low".

In the case of a "high" sound, the distance the clutch lifts is an empty stroke, while in the case of a "calm" and "low" sound, the speed of lifting the clutch must be slowed down.

For flat road start and downhill start, you can first put down the manual brake, and then step on the accelerator and lift the clutch; The uphill start can only be lowered when you hear the sound of the accelerator changing to "calm", otherwise the car will slip backwards.

When starting on a flat road and starting downhill, you can complete the start with a little oil; The uphill start needs to determine the amount of pressure on the accelerator according to the size of the slope: the greater the slope, the greater the refueling. At the moment of putting down the hand brake, temporarily stabilize the clutch (do not continue to lift up), and add more fuel to avoid the car shaking and unsteady.

When starting downhill, if the car has been turned off and the slope is large, you can directly hang the third gear without ignition, release the brakes, and start. By increasing the speed of the wheels, the car can be automatically ignited. (Photo by Li Linwei) @2019

For automatic cars, since it is enough to release the brake pedal and then press the accelerator pedal when starting, the problem of starting off generally does not occur. For cars with manual transmission, the way to prevent the car from stalling at the start is very simple, just press the accelerator when you release the clutch pedal.

Generally speaking, the engine speed is too low due to the poor coordination of oil separation, resulting in the engine fire and finally stalling. This situation is relatively simple to solve, you can press the throttle a little deeper at the start to keep the engine speed in a high range, or you can manually adjust the idle speed of the car to solve the problem of the car starting off.

The automatic transmission car will definitely not turn off when it starts, and the manual transmission car will not turn off the oil if it wants to start without turning off.

Press the clutch and start the switch for a little more time.

1. Start on flat ground.

Make sure your car is parked on a road that doesn't pull the handbrake and doesn't slip behind.

Operation: step on the clutch, hang a gear, refuel (refuel) first, make the speed reach more than 1500 rpm, and stabilize the throttle; , fast release to one-third of the total stroke (fast release); Slowly release the clutch while feeling whether the car is moving forward (slow release); When the car moves forward slowly, step on the clutch with the left foot and stay still, add some fuel to the right foot (parking - refueling), slow down the clutch (slow release), (just with the throttle lag), and the start is successful!

Operation: Hit the brake with your right foot, use a little force, but make sure the car does not slip behind; (Brake) step on the clutch, hang a gear, release the clutch quickly to one-third of the total stroke, and slowly release the clutch; (fast - slow down), note: when the tachometer drops, the left foot steps on the clutch and stays still; (Parking)!

Look up at the front while your right foot quickly moves from the footbrake pedal to the accelerator pedal to add some fuel (refuel); Slowly release the clutch with the left foot, and when the car slowly moves forward, you can hold the clutch for a while, and then slowly release the clutch. (Slow down).

Due to the steep slope, you need to use the handbrake to get started.

After quickly releasing to one-third of the total stroke, slowly release the clutch; Note: When the tachometer drops, the engine sound will become heavy;

Hold the clutch with your left foot and stay still (parked).

Hold still after releasing the clutch with your left foot a little more slowly, release the handbrake, and the start is successful!

Novices on the road, especially those who drive manual transmission cars, are a little nervous when they stop at a red light, because the car always turns off at the start, and it can't catch fire for a long time in a hurry. How does a car start without turning off? Consulted some veteran drivers and came to the conclusion:

The key to avoiding starting and stalling is to master the contact points of the clutch. To solve the problem of car stalling, we must first understand the reasons why the car stalls. How does a car start without turning off?

The next is how to solve the problem of car stalling for novice drivers: how to start the car without turning off 1, technical problems, you need to improve your driving skills after quickly running in with the car. 2. Use high-standard, high-quality and qualified fuel.

3. Clean the oil circuit thoroughly, including fuel injectors, throttle valves, fuel tanks, etc. Because there may be a problem with the car stalling, the oil road is blocked, and the oil supply is not smooth, and the engine will turn off. 4. This is a special situation, when the car stalls at idle, the main reason is that there is too much dust in the air, and there is a lot of dirt deposited at the valve core of the idle motor and the throttle seat when the engine is running.

If there is too much dirt accumulation, the engine will idle too low, idle stability will be poor, and the engine will idle and stall when driving. The solution to this problem is simple: just clean the idle motor.

If you are driving a car, you should feel the temper of the car (the contact point of the clutch), quickly press the accelerator pedal after the clutch contacts, increase the engine speed, and at the same time you should boldly release the clutch, after a few times, you will feel very good, which is also commonly referred to as "oil release fit".