What tools do you need to build a computer?

1. The most basic tool for assembling a computer with a screw cutter is a screwdriver.

It is best to buy a screwdriver with a magnetic one, which will make it easier when installing various parts. Most of the accessories in computers use a "ten" shaped screwdriver, and one of the benefits of choosing a magnetic screwdriver is that it can easily hold the screws for installation in tight spaces. 2. Another practical tool for assembling a computer is needlenose pliers.

When screwed. It is much more convenient to use needle-nose pliers when it is not screwed, and it is convenient to cut it short with needle-nose pliers when some wires are too long. 3. Tweezers Tweezers are particularly convenient when taking out small screws and inserting wires in small spaces. Tweezers can also be used to pick up objects that have fallen into the dead corners of the case, and can also be used to set jumpers on hardware.

4. Multimeter.

The multimeter is used to check the voltage and troubleshoot during installation.

Accessories for expanding data to assemble a computer are: CPU, motherboard, memory, graphics card, hard disk, optical drive, monitor, chassis, power supply, keyboard and mouse. Assemble accessories for your computer and laptop.

Desktop computers are a bit larger than laptops. The first time you build a computer is lower than that of a branded computer, but the quality is not necessarily guaranteed. Because it is assembled, the accessories may be fake, parallel import, or second-hand, and a certain amount of expertise is required when purchasing, as well as considering whether each piece of hardware is reasonable.

Assembling computers is generally purchased in computer malls or computer stores, such as Pacific Computer City, Bainaohui, etc. It is also possible to buy online, such as Alibaba.

Computer accessories are plugged and unplugged, at most with a screwdriver (flat, cross).

First of all, the computer hardware must be ready, such as: chassis, power supply, motherboard, CPU, memory module, hard disk, optical drive, data cable, etc. Others, such as others, such as:

Screwdrivers (one cross and one slot, one each), preferably a pair of anti-static gloves, brushes, erasers, etc.

The computer assembly tutorial is as follows: Tools: CPU, with Peiqi motherboard.

1. First of all, we take out the CPU and the motherboard, as shown in the figure below: 2. The installation of the CPU and the motherboard, we must pay attention to the fact that the motherboard and the CPU have corresponding foolproof gaps, mainly to prevent the CPU from being installed in the opposite direction, we will put the CPU lightly in the CPU slot of the motherboard, and the process must be handled lightly to avoid accidentally bending the pins. 3. Press down the lever of the motherboard socket to open the lid of the CPU socket, as shown in the figure below

4. We put the CPU into the CPU slot of the motherboard, note that the CPU and the CPU slot of the motherboard have a foolproof gap, and the CPU installation is reversed and cannot be put in, as shown in the following figure: 5. Press down the lever, restore the lever to the previous position, and complete the installation of the CPU, at this time, the black cover on it will also be detached, as shown in the figure below: 6. As shown in the figure below, the CPU has been installed, and the black cover is useless, and it can be thrown away, mainly before it is installed, Prevent the pins of the CPU socket from being touched.

7. Complete the installation of the CPU and the motherboard.

1. Open the chassis and install the power supply in the chassis.

2. Insert the CPU chip into the CPU socket of the motherboard, apply thermal grease, and install the heat sink and cooling fan.

3. Insert the memory module into the memory slot of the motherboard.

4. Install the motherboard in the chassis at the position of the motherboard, and plug the power cable of the power supply to the motherboard.

5. Install the graphics card on the graphics card slot on the motherboard.

6. The current sound cards are all PCI interfaces, so insert the sound card into the PCI slot.

7. Install the hard disk and optical drive in the chassis, plug the data cable into the corresponding interface of the motherboard, and connect the power cable.

8. Connect the control cable of the chassis panel with the motherboard, that is, the connection of various switches, indicator lights, and PC speakers.

9. Connect the signal cable of the monitor to the graphics card.

10. Power-on test whether the system can start normally.

Phillips screwdrivers, wrenches, but also you have skills.

It's basically just a screwdriver, and you have to understand.

A screwdriver or a drill will do.