How to deal with the slippage of the folder gluer belt?

The belt of the folder-gluer has been used for a long time, the belt is stretched, it will slip, it is recommended to use a better belt, I just changed the belt of the wire drawing machine for my friend yesterday, the belt is also stretched and loosened, the tension is not enough to cause slippage, after he changed the good belt, it is no problem to use it for more than a year, the belt of the wire drawing machine and the folder-gluer belt are a kind of belt, the base belt, if you need help, please continue to ask questions, or check my information private message me.

1.Slipping of the belt of the heavy hammer tensioning belt conveyorThe belt conveyor using the heavy hammer tensioning device can add a counterweight to solve the problem when the belt slips, and add it to the belt until it does not slip. However, too much should not be added, so as not to expose the belt to unnecessary excessive tension and reduce the service life of the belt.

2.Slippage of spiral tensioning or hydraulic tensioning belt conveyor: Adjustable when slipping occurs using spiral tensioning or hydraulic tensioning belt conveyor.

Tension stroke to increase tension force. However, sometimes the tension stroke is not enough and the belt is permanently deformed, in which case the belt can be cut off and vulcanized again.

3.The use of nylon tape or EP requires a long tension stroke, and when the stroke is insufficient, it can also be re-vulcanized or increased to tighten the stroke.

Belt conveyor equipment failure analysisThe belt mistracking of the conveyor is the most common failure of this series of machines. There are two main types of fault causes and troubleshooting methods.

1. The axis of the driving roller at the head of the conveyor and the reversing roller at the tail is not perpendicular to the center line of the conveyor. Cause the belt to deviate to one side at the head or tail of the conveyor. When the roller is deviated, the tightness of the belt on both sides of the roller is inconsistent, so the traction force along the width of the belt is also inconsistent, and it becomes an increasing or decreasing trend, so that the belt produces a moving force in the decreasing direction, resulting in the belt to the loose side of the deviation, that is, the so-called running loose does not run tight.

The troubleshooting method is very simple, the bearing seat position of the head and tail roller of the general belt conveyor is equipped with adjusting bolts, if the belt deviates to the right side of the head drum, we will adjust the right bearing seat of the head drum forward or adjust the left bearing seat backwards. If the belt deviates to the left, adjust the left housing forward or the right housing backwards. The tail reversing roller is adjusted in the opposite direction to the head drive roller.

If it can help you, or like, thank you.

Stick the surface of the flat belt of the box machine, with imports, let the manufacturer kill the rough surface when leaving the factory, increase friction, if you slip after a few months, you can scrub the belt surface with alcohol or rosin perfume, if the belt is too long and slippery, then it is time to consider replacing the belt, you can try each way, I hope it can help you.

1. Check whether the load of the folder-gluer belt exceeds the standard. If the load is too large and exceeds the capacity of the motor, it will be easy to slip, although the slippage at this time can play a role in protecting the motor, but it is necessary to adjust the feeding amount in time to control it within the maximum load to avoid the appearance of material slippage.

2. If the starting speed is too fast, it is easy to cause the belt of the folder-gluer to slip. In view of this situation, the starting speed can be adjusted appropriately and the slow start can be used instead, which can effectively cause the customer to slip.

3. It is necessary to eliminate slippage caused by insufficient friction between the transmission roller and the conveyor belt. Usually this is caused by water on the conveyor belt or a humid environment, and a blower can be used to blow the rosin powder on the drum.

4. Check the tension of the folder-gluer belt.

Qingchuan everla folder-gluer belt.

Yonghang provides a few points 1, the starting speed is too fast can also form skidding. At this point, it can be started slowly. If the squirrel cage motor is used, it can be jogged twice before starting, which can also effectively overcome the slippage phenomenon.

2. The initial tension is too small. The tension leaving the drum is not enough to cause slippage. This situation generally occurs at start-up, and the solution is to adjust the tensioning device and increase the initial tension.

3. The load is too large, and it will slip if it exceeds the capacity of the motor. The positive side of skidding at this point is that it protects the motor. Otherwise, after a long time, the motor will be burned. But for operation, it is a skidding accident.

4. The friction between the transmission drum and the belt is not enough to cause slippage. Most of the reasons why it should not be carried are water or the environment is humid. The solution is to add some minced rosin to the drum. However, be careful not to add it by hand, but blow it in with a blower device to avoid accidents.

5. The tail roller bearing is damaged and does not rotate or the upper and lower roller bearings are damaged and do not rotate too much. The reason for the damage is that the tail floats and sinks too much, and the parts that have been damaged or rotated inflexibly are not repaired and replaced in time, which increases the resistance and causes slippage.

The folder-gluer belt box can't go through, and this situation is also commonplace on the folder-gluer belt. This is mainly due to the following two points:

The first point is that the center line of the device is not parallel, which will make the belts on both sides inconsistent.

The second point is that the quality of the belt of the folder-gluer is unqualified, which is determined by the mold, such as uneven elongation and unstraight bending, which makes the belt deviate during the operation of the equipment, so that it cannot go over!