The alarm will be turned on and it will be beeping for a long time, and the memory is fine

The start-up alarm keeps beeping, only it may be a memory problem. Don't say it's not a memory problem, trust the sound of the alarm, and trust the science!

The memory is good, the memory slot is bad. If the memory slot is good, the memory must be bad, don't fight with me, check it out for yourself.

I'm a computer repairer, and I've been working for six years.

It is recommended to plug in the original graphics card, wipe the gold teeth of the memory module with a soft cloth, clean the memory slot, then reset the BIOS, turn off the monitor, and reboot the computer.

Apparently a problem with the motherboard's memory slots.

I suggest you don't toss the second-hand board you got from **, go back to him quickly, or you will lose it

It's a problem with the memory, and you say that there is no problem with the memory, isn't that the problem with the slot?

Either there is a problem with the wiring of the motherboard, in short, there is a problem with the motherboard.

You'd better go and find it

This problem is that your memory and graphics card are not connected well, sometimes it is not well connected, and you can't say anything when it's okay, this problem is very common, you say that the boot file loss is your hard disk has a bad sector.

Alcohol to wipe the slot with anhydrous alcohol, or go to the pharmacy to buy medical alcohol is preferably 93% or more.

Memory slots rarely break! It is estimated that there is a problem with your power supply and chassis that caused the BIOS and IO chips on the motherboard to burn! Take it and fix it!

Let me start by saying that 440 is better than 9100, 440 is equivalent to 9200, and the probability of a bad memory slot is very high.

A machine that takes a long time and the memory slots are oxidized.

It's easy to break, don't touch the motherboard, take it to a repair shop.

The slot is broken, and it can be repaired if it is not serious.

The memory slot on the motherboard is broken! Wipe it with alcohol to see if it works, if it doesn't work, change the board, there's no way.

1 Short: The system boots normally. This is something we hear every day and it also shows that there is nothing wrong with the machine.

2 Short: General error, please go to CMOS setup and reset the incorrect option.

1 Long 1 Short: There is an error with the RAM or motherboard. Try to change the memory, if it still doesn't work, you have to change the motherboard.

1 Long 2 Short: Wrong monitor or graphics card.

1 Long 3 Short: Keyboard controller error. Check the motherboard.

1 Long 9 Short: Motherboard flash RAM or EPROM error, BIOS corruption. Try a different block of flash ram.

Constant ringing (long sound): The memory module is not plugged in tightly or damaged. Reinsert the memory module, if it still doesn't work, only.

Replace a memory.

Ringing: The power supply and monitor are not properly connected to the graphics card. Check all the plugs.

Repeated short rings: Power supply issues.

No sound, no display: Power issue.

There's a problem with the graphics card.,Plug the graphics card back in,Clean up the dust.,See if it can start normally.,If it can't start normally.,According to what you said, the screen will be blurred.,There may be a problem with the video memory.,Then you need to change the graphics card to see.。

Erase the gold finger of the memory with an eraser, and then scrape the memory slot of the motherboard.

Graphics card problems,One long and two short,Sometimes you can enter the system,There is a flower screen,Sometimes it is not displayed,You try to change a graphics card,It should solve the problem。

If you can self-test, you can reinstall the system.

Let's change the memory. You're not unplugging the memory yet. On the top floor.

The graphics card is loose, and if it is pressed, if not, unplug the memory module and plug it in.

Is the memory module incompatible with the main version?

If it is added to the original memory module, it may be incompatible and poor contact, and the computer has been alarming is a very uniform sound, that is, it keeps ringing, indicating that the memory module cannot be read, or the memory module is not plugged in well. You can clean the lower slot, and then use an eraser to erase the copper under the lower memory module. Plug it in tightly.

Remember to take out the battery on the motherboard and discharge it for two minutes, if it still doesn't solve the problem, it must be a problem with the memory module itself. Just go and replace one.

The memory is not plugged in properly or the memory does not match.

AMI's Virtual BIOS Self-Test Bell and Its Significance.

1 Short: Memory refresh failed differential key. Replace the memory module.

2 Short: Memory ECC verification error. Setting the memory option for ECC check to Disabled in CMOS Setup will solve the problem, but the most fundamental solution is to replace a memory.

3 Short: The system basic memory (1st 64kb) check failed. Change memory.

4 Short: The system clock is wrong.

5 Short: Processor (CPU) error.

6 Short: Keyboard controller error.

7 Short: The system is in real mode and cannot be switched to protection mode.

8 Short: Displays a memory error. If there is a problem with the display memory, try changing the graphics card.

9 Short: ROM BIOS check and error.

1 Long 3 Short: Memory error. If the memory is damaged, it can be replaced.

1 Long 8 Short: Displays test errors. The monitor cable is not plugged in properly or the graphics card is not plugged in properly.

The biggest possibility is that your machine's motherboard is broken, check your motherboard.

It's because you don't plug it in, you plug it back in, it should be fine!

It should be the motherboard's memory slot that is broken.

The reason for the alarm is that the computer is on and the alarm is a memory problem.

Troubleshooting:

1. First clean up the memory module, remove the memory module (use your fingers to pull the card of the memory slot to both sides), wipe it with an rubber band, and then reinstall the memory module (align the memory module with the bayonet, hold both ends of the memory module, and press it down slightly). Turn on the computer to see if it can start the computer. Most of the computer beeping problems can be solved.

2. If the first step is still invalid, then you can only replace the memory slot first, see if the slot is broken, and then reinstall the memory.

3. If the problem of Changming cannot be solved, it means that the memory module has been damaged and needs to be replaced.

Note: There are many alarm sounds when the system starts: for example, one long sound and two short sounds indicate an error in the monitor or display card; Repeated, short beeps indicate a power supply problem.

If you can't wipe the memory, it means that the memory is a little broken, so it's better to try changing the memory.