What is the reason for the Glash tte watch to be parked?

Watch stealing is related to problems such as watch stoppage, watch bumps, and hairspring failures. Watch steal stop is when the watch has enough power, the watch stops, and after a period of time it starts to move again, so that the watch will slow down, that is, the watch steal stop phenomenon.

Watch stopping: Anyone who understands mechanical watches knows that fully automatic mechanical watches are wound by swinging on the arm, if the watch is placed for too long and the arm movement is insufficient, the watch will be insufficient in potential energy, and the watch will be unstable when it travels, and there may be a sneak stop at night.

If this is the case, you can manually perform an arc motion before placing the watch.

Watch bumps: In the process of wearing the watch, because you may accidentally bump into some hard objects, if you accidentally bump the watch in daily use, it will cause the parts in the watch to loosen, resulting in the watch stopping.

After such a situation, it is recommended that you go to the after-sales service for maintenance in time to avoid more serious damage.

Hairspring failure: hairspring failure will also cause the watch to stop, if the usual amount of activity is too large, the watch will be particularly tight, the spring will produce a malfunction, and there will also be a lack of power. This usually happens at night.

If the watch stops or the time is inaccurate, it is recommended to overhaul the watch in time.

The reasons for the watch to stop are as follows:

Kinetic energy is insufficient, and automatic watches use the movement of the arm to complete the winding. If the watch is left for too long or the amount of arm movement is less every day, the mainspring energy of the watch will be due to insufficient winding, and it is easy to produce inaccurate timing or night stopping.

The hairspring is faulty, and the clockwork will be tighter if the amount of exercise is large. If there is a problem with the upper bar mechanism that causes insufficient power, it generally appears between 9 o'clock and 12 o'clock in the evening, "with a calendar function table" because at this time the hour wheel begins to drive the calendar wheel, and the load is large, if the power is insufficient, it is easy to stop during this time period. This time should not be reversed dial pin, now many mechanical watches use plastic parts of the calendar wheel, accidentally will break the gear, once the tooth is broken, every day at this time will be stuck, or to a fixed date will no longer jump.

As a result, the mechanical watch was stopped.

Bump failure, the watch is a precision instrument, once the bump receives a violent vibration, then the parts may fall off or damaged, you can make the watch steal stop.

Quartz watch stealing reasons.

1) Insufficient power: Quartz watch, when there is a steal stop, the battery needs to be replaced due to insufficient battery power.

2) Poor contact: The circuit board of the quartz watch is not in good contact, and the watch is also prone to steal stop.

3) Faults in the movement: If there are some gear train failures in the movement, steal stops will occur.

The reason for the mechanical watch to stop.

1.Insufficient power: mechanical watches are divided into manual mechanical watches and automatic mechanical watches, insufficient power is an important reason for the watch to slow down or stop the watch, manual mechanical watches can be wound directly when slow, and the reason why automatic mechanical watches are slow is mostly because of insufficient wearing time or the arm does not maintain a normal amount of movement, and it can be directly manually wound to supplement the power.

2.No maintenance: mechanical watches are generally maintained once every 2 to 3 years, the watch is used for a long time, the lubricating oil in the movement will dry up, and the friction of each gear for a long time will produce iron filings, increase the friction between the gears, this kind of problem only needs to clean the movement, re-refueling.

3.Shock: A mechanical watch has a complex structure and is composed of hundreds of precision parts, which is very fragile, and the watch is subjected to a strong impact, and the parts in the movement may loosen and cause the watch to slow down or stop.

According to the reason why the watch is slow, you can take corresponding measures, pay attention to the winding of the manual machinery, maintain the normal amount of exercise of the automatic mechanical arm, maintain it on time, pay attention to the watch waterproof, shockproof and anti-magnetic, and send it for repair in time if there is a problem.

4.Hairspring failure, hairspring failure is also one of the reasons for the mechanical watch steal stop, the above mentioned lack of power caused by steal stop, on the contrary, if the amount of exercise is too large, the clockwork is relatively tight and causes the failure of the upper bar mechanism, it will also cause insufficient power, this situation generally occurs at about 9 o'clock to 12 o'clock in the evening, at this time, the watch with calendar function turns the roulette wheel, which will lead to insufficient power calendar jam to stop the watch. This kind of technical failure also needs to be tested and repaired by a professional watch repair shop.

Reason for watch stealing:

1. Anyone who knows a little about mechanical watches knows that fully automatic mechanical watches rely entirely on the swing of the arm to complete the winding. Therefore, if the watch is left for too long or the amount of arm activity does not meet the requirements of the watch winding every day, the watch will cause the mainspring to be winding and the potential energy is insufficient, which will cause the watch to be unstable or stop when it is not worn at night.

2. If you accidentally bump or fall into the watch in daily use, and hit the watch hard, it may cause the movement gears and other parts in the watch to loosen and misalign, which will also lead to the situation of stealing the mechanical watch.

3. The failure of the hairspring is also one of the reasons for the stealing of the mechanical watch when it is running normally. If the amount of activity is too large, the winding mechanism will malfunction due to the tightening of the mainspring for a long time. It can also cause a lack of motivation.

The more common reason may be a lack of kinetic energy, but some friends may say that I buy a fully automatic mechanical watch, and I don't need to wind it myself. In fact, this is a big misunderstanding, automatic mechanical watches do not need to be wound manually, but to keep the mechanical watch on the hand to wear at least 8 hours of time, because the automatic mechanical watch is the use of the arbitrary swing of the rotor to wind up, and the rotor is swinging with the movement of the arm, so if the mechanical watch needs to be worn on the hand often.

But what if you wear it on your hand a lot and don't leave? Don't worry, it may be a lack of kinetic energy, and then we need to manually wind the clockwork.

After passing the above methods, what should I do if I also find that the machine is not gone? Here we can rule out the reason for the lack of kinetic energy of the mechanical watch, it should be that the mechanical watch is faulty, if you are not a watch professional, it is best not to disassemble it rashly, please send it to a professional watch repairer for repair. Before the watch bar talked about the maintenance method of mechanical watches, mechanical watches need more maintenance than quartz watches, here is an emphasis on the maintenance methods of mechanical watches:

1.If it is a manual mechanical watch, the mechanical watch should be wound regularly, and it is recommended to wind the mechanical watch around 8 pm.

2.Automatic watches, such as insufficient arm movement, need to manually wind the watch, and the rotation of the crown needs to be controlled within 20 turns.

3.If an automatic watch has not been worn for more than 40 hours, it is necessary to turn the crown twenty times to activate the movement's drive system.

4.Regardless of the water resistance of the watch, it should be avoided as much as possible, and if it does, wipe it dry and make sure that the crown is locked at all times. It is best to replace the waterproof ring once a year.

What should I do if the mechanical watch is gone? We need to establish the common sense of protection of mechanical watches in ordinary times, and when we encounter the situation that we can't go, we don't need to worry, and we can eliminate them one by one according to the above methods, which are usually caused by insufficient kinetic energy.

Reason for stopping:

The more common reason may be the lack of kinetic energy, automatic mechanical watches do not need to be manually wound, but to keep the mechanical watch on the hand to wear at least 8 hours of time, because the automatic mechanical watch uses the arbitrary swing of the rotor to wind up, and the rotor swings with the movement of the arm, so if the mechanical watch needs to be worn on the hand often.

But if you often wear it on your hand and don't go, it may also be a lack of kinetic energy, and then we need to manually wind it.

After the above methods, the machine is not gone, here we can rule out the reason for the lack of kinetic energy of the mechanical watch, it should be the failure of the mechanical watch, if you are not a watch professional, it is best not to disassemble it rashly, please send it to a professional watch repairer for repair.

Insufficient kinetic energy: The watch is not winded enough, and the kinetic energy is insufficient;Gear failure;Lack of maintenance will now cause the watch to stop, the specific situation requires you to go to a professional repair center for testing and processing. It is recommended to choose a professional repair center to avoid losses to your watch, the specific situation needs to be tested and processed by a technician, it is recommended to call ** detailed consultation.

Mechanical watches can generally be divided into the following two types: manual and self-winding. Hand-wound watches are powered by hand, and if the watch suddenly stops, you have to consider the lack of power.

Hand-wound watches should be wound at the same time every day as much as possible so that the watch has enough energy to function in the next 24 hours.

The principle of a self-winding watch: it operates by the action of the automatic winding mechanism that can tighten the mainspring by turning the rotor in any direction. That is, many cousins say that when you wear it, the shaking movement has a sound similar to that of a balance wheel.

Cousins who don't know this principle, some even think that which part is loose and rotating, but it is not. It is a self-winding component that is automatically wound. Generally, a fully automatic watch should be worn on the hand for more than 8 hours a day to make up for the amount of clockwork, but it is not absolute, and it is adjusted according to the amount of exercise you have.

If you have a large amount of exercise, you can store enough energy on the wind, and you can wear it for a few hours to be used for a day, and you don't need to manually replenish the chain frequently. If the amount of exercise is small, it is necessary to properly supply the manual to maintain the normal mechanical operation.

If it is found that the reason why the mechanical watch does not go is not due to insufficient kinetic energy, it is that the mechanical watch is faulty and needs to be sent to a professional maintenance personnel for repair. Remember not to talk about mechanical watch disassembly yourself. Mechanical watches are driven by mechanical gears and clocksprings, and friction is inevitable when turning, so it is necessary to add oil and lubrication over time to reduce the wear rate of parts.

Otherwise, wait until something goes wrong to send it for repair, and the problem is often very serious.

1.Mechanical watches rely on mainspring windings to provide power, and the timekeeping is carried out by means of gearing. Mechanical watches are divided into manual and automatic winding.

Due to the complex structure, the phenotype is thicker and heavier. Because of the characteristics of the principle of time, it is affected by gravity, mechanical friction, temperature changes, usage and other reasons.

2.Mainly from the wearer's wrist activity, the wrist of the watch swings when the owner is active, so as to wind the watch, so when the wearer usually does not move much or does not wear it for a long time, the string force will be insufficient or empty, resulting in the watch is not accurate or stopped.

3.Automatic watches rely on the swing generated by relative motion to automatically wind, if the belt is in the hand, it is in a relatively stationary state for a long time, the watch can not be automatically wound, it will lose the ability to time, and there will be stopping.

4.Users only need to swing the watch dozens of times or up and down a few times (with hand adjustment function) to restore time. If you want to ensure that the automatic mechanical watch walks accurately, you should wear it normally for more than 8 hours a day.

Stop, there may be the following reasons:

1. See if the crown is pulled out, the crown is pulled out, and the watch stops.

2. Whether the second hand touches the glass, there will be a circle mark on the glass.

3. Whether the three watch hands are not well balanced, causing contact and causing stopping.

4. Whether the battery is exhausted or not, it generally needs to be replaced in 1-2 years.

Glashütte Watch Aftermarket Repair Center: 400-659-0877

Mechanical watches are generally divided into two types: manual winding and mobile winding, and the power source of both mechanical watches is driven by the clockwork drive gear in the movement, but the power source is different. Generally speaking, there are many reasons why the second hand of a watch does not move, but it is mainly due to the lack of power of the watch, the loosening of the second hand in the watch, and even the loss of parts caused by damage to the inside of the watch movement. It is also possible that the watch has been left for too long and the oil sludge is too dry, so when you find that the second hand of the mechanical watch does not move or even the whole thing does not move, do not panic too much, you must first find out what is the reason why the second hand in the watch does not move, and then analyze it specifically.

The solution to the mechanical watch stealing stop: 1. Wear more than 10 hours a day, especially for automatic mechanical watches, the efficiency of automatic winding is low, and the amount of arm activity is larger, and the wrist is too small to type on the keyboard while wearing the watch, and the winding efficiency is very low. If the amount of exercise is small, it can be wound by manual winding.

2. Pay attention to the shockproof, dustproof, anti-magnetic and waterproof of Chopard watches. It's a good idea to take your watch off when doing strenuous exercise or doing laundry or bathing. 3. Remember to take care of your watch, if you don't maintain it for a long time, a lot of sludge will be generated and silted inside.

Friction between gears increases, causing slippage. If it involves a faulty part of the Chopard watch movement, you need to send the watch to a professional watch repair center for inspection and repair.

How much did you buy it? I can only ask this, Glashütte is a famous German watch, each piece is more than 50,000, and there is no cap. At the top of the seven-digit range, Glashütte's watches are known for their precision and meticulousness, which is also the style of German companies.

The second is that automatic watches do not stop watching. If it's not a manual machine, if you take the watch all day, I guess you've been fooled.