EPSON1390 what happens when the printhead suddenly slows down during the printing process?

Cause: The Epson inkjet printer motherboard chip has a program to detect the printer's operation. This procedure is to manage the thermal protection of the motor.

When the temperature of the printer's continuous motor rises to a certain set value, the chip will send a command to the printer to reduce the printing speed to protect the motor from overheating. At this point, the printer speed will be reduced. If you continue printing, the speed will be further reduced to an unbearable slowness.

Solution: 1. If the number of prints is small, the printing speed slows down significantly, indicating that the motor is aging. If the aging is not severe, you can use the P50 repair (clearing) software to reset the thermal protection value of the motor, which can be significantly improved.

If the effect is not obvious, you can add a heat sink to the motor, or replace the motor.

2. When the number of prints is large, it is unavoidable. The upper cover can be opened and the upper cover detection key can be pressed (otherwise it will not be able to print), which improves the heat dissipation effect and alleviates the number of prints.

3. Turn off the printer for about 10 minutes. Then turn on the printer again.

Many netizens said that it was a problem with the motor, and I also had this situation today, and I thought about it, why the motor will be thermally protected, I think there is resistance. I tried to clean and wipe the round metal rod of the printer moving the printhead back and forth, and then apply some grease appropriately, and then return to normal. Printing the entire A3** was also resumed at the end of the two slower strokes.

Try not to use engine oil instead of grease, you can try it temporarily, it seems that the oil will be sticky after a long time.

The real reason why printers are slowing down.

1. The lubrication of the ink cart guide rail is not smooth, which causes the ink cart to be blocked and the printing slows down.

2. Due to the long-term work of the ink car motor, the heating degree exceeds the upper limit set by the main board of the machine, and the machine enters the protection mode and the printing slows down.

There are several ways to solve it, and it is recommended to use them at the same time:

1. Add lubricating oil to the guide rail, and the running speed of the printer trolley will be accelerated after using the lubricating oil.

2. Use Epson's maintenance software to brush the motor, you can search for this in the major forums, please note that when using this method, the motor must reach room temperature before proceeding, otherwise it will be invalid (Note: Do not turn on the printer if it is placed for more than 5 hours).

3. Remove the shell of the machine and install a heat sink on top of the ink car motor. With the above methods, the problem of the inkjet printer slowing down can be easily solved.

This can be solved by:

1. Right-click on the left side of the computer - program - printer - to open it, or open it in the control panel.

2. Right-click [Printer - Properties] and select the second [Share] option in the "Properties" dialog box to ensure that the printer is in the shared state.

3. Select the [Advanced] option in the "Properties" window, and check whether the [Print in Background so that the program can print quickly] radio button is selected in the open dialog box, if it is selected, it means that the printer has started "spooling printing".

4. At this moment, it should be noted that if you select "Print directly to the printer", it means that the printer has disabled the "spooled printing" method and uses the direct printing to the printer method.

5. Now the problem is to speed up the printing speed, then you can cancel the "spooled printing" printing method, that is to say, select "print directly to the printer", <

6. After the settings are completed according to the prompts, remember to restart the computer and print again, and the printing speed will be faster.

HP 2132 printer, printing speed and copy speed suddenly became very slow, and some words were not clear. I want to ask, what's going on?

We recommend that you print the offline configuration page first to see if the speed of the offline configuration page is normal. The offline configuration page is printed as follows:1

Press the menu button of the printer to enter the menu, and press until information appears. 2.Press and hold the Degree key until the Print Configuration page appears.

3.Press the key to print the configuration page. The printing configuration is displayed on the display and the configuration page is printed.

If the printing speed on the offline configuration page is also slow, it is recommended to reset the printer's specific settings. However, the reset will erase all the settings of the machine and restore the machine to its factory state. The reset method is as follows:

Shut down first, after booting, when the current memory is detected, press quickly, until 3 lights are on, let go, the panel displays select language, press the arrow keys to select cold reset, press If the reset is invalid, the printing offline configuration page is still slow, it may be a hardware failure of the printer.

Epson printer suddenly slows down solution: 1. If the response time of the printer is slow after sending the print command, it is because the computer is processing data, and the long response time is related to the processing performance of the computer. Second, if the printer responds to the printing stupid and slow, please try the following:

If Lao Kai's requirements for printing quality are not very high, please click "Start" in the lower left corner of the computer - >Equipment and Printers" or "Printers and Fax", right-click the L800 printer icon and select "Printing Preferences" - >Main Window" - > "Printing Paper Type" to "Ordinary Paper", and "Quality" to "Economy"; If you don't want color printing, check "Grayscale mode with vertical". Hope mine can help you.

Is it a lot of copies? The general printer will have the phenomenon of slowing down when working continuously, sometimes to prevent the machine from overheating, and the color printer sometimes needs color correction, and it will return to normal when it stops working and restarts.