How to set up wifi in the VISTA system of laptop? Ask for a detailed process! Thank you!!

This is win7、XP setting method,I don't know if it's useful.,I haven't used the Vista system.。

Laptop to do wifi hotspot tutorial.

Step Method.

1.Right-click the network.

2.Click Properties - Set Connection or Network.

3.Set up a wireless ephemeral network.

4.Next.

5.It's best to choose "No Authentication (Open)" for this step, which will be a little faster. At the same time, you don't have to worry that others will grab your resources, because this kind of hotspot only allows one person to share the Internet, and others can't connect to the Internet even if they can connect to the hotspot.

At the same time, select "Save this network" to save the next boot and set it up.

6.Set up your wireless.

7.Once the wireless setup is complete, right-click the network icon again to enter the Network and Sharing Center

8.Go to Manage Network Connections

9.Select both Local Connect and Wireless Connect, then right-click and select Bridge

10.The bridge was successfully built.

11.Right-click on the wireless connection.

12.The computer connection 123 is successful.

13.Then the mobile phone wifi will search for this hotspot, and after connecting, wait for about three or four seconds, it will be assigned an IP address, and then you can access the Internet. Of course, the premise is that your laptop has Internet access. If the connection is successful, it will be displayed as shown in the figure below.

Run the command prompt as an administrator.

Run the following command to enable the virtual wireless network card (equivalent to turning on the router):

netsh wlan set hostednetwork mode=allow ssid=test key=***8 bits or more).

There are three arguments in this command:

mode: Whether to enable the virtual Wi-Fi network card, change to disallow to disable, and the virtual network card will disappear.

SSID: Specifies the name of the wireless network, preferably in English.

key: specifies the password of the wireless network. This password is used to encrypt the wireless network with secure WPA2, which can prevent the network from being rubbed off.

The above three parameters can actually be used separately, for example, only mode=disallow can directly disable the virtual wifi network card.

2.Enable Internet Connection Sharing (ICS).

Right-click in the bottom right corner of the desktop"Networking"Open the tethering center > change the adapter settings, you will find that there is one more Microsoft Virtual Wi-Fi miniport adapter, right-click on your local connection (non-wireless connection), that is, the wired network card you are currently connected to the network, select Properties, click on sharing, check the "Allow other network users to connect through this computer's Internet connection" option, At the same time, select the virtual network you just created in the drop-down menu (Wi-Fi 2 3).

3.Continue typing in the command prompt: netsh wlan start hostednetwork This step is to turn on the virtual wireless network just now, so that your wifi phone can be linked to the virtual wifi network you just built, but the trouble is here, every time you turn on the computer, you have to enter the command of this step if you want to use the virtual wifi hotspot.

You can create an ADSL broadband connection for your Windows Vista computer by following these steps:

1. Start Network Control Panel Network and Sharing Center Set up connection or network Connect to Internet broadband pppoe Enter password, connection name Connection;

2. Create a shortcut: Network and Sharing Center Manage network connections Find a broadband connection, right-click and select Create shortcut.

It is recommended to install XP or Win7

That's the over-the-top system.

Vista can set up WiFi hotspots. You create a new network connection, point to a computer-to-computer link, and then look at the settings yourself. Step by step, and eventually a shared network will come out, and it's OK to share it.

touch search and you're good to go.

If the computer with the Vista system has a wireless network card (the current mainstream notebooks have a wireless network card), and then use the software to share the WiFi (the Vista system is compatible with 360 Security Guard), the method is as follows:

2. Find "Free WiFi" and click to open the tool.

The computer wireless network card switch is turned on, FN key + F5 key.

Right-click in the lower right corner of the desktop to connect to Wi-Fi, automatically.

Premise: Your network provider does not restrict you from using routers.

It's not your computer's problem, and there's no need to set your Vista desktop as a WiFi hotspot, it's just that the routing is incorrect.

1. The WAN port of the cat network cable is routed to the LAN port of the machine.

2. Follow the instructions to reset (not restart) your router first to avoid confusion in settings.

3. Follow the manual to log in to the routing setting interface (tp-link is generally, admin, admin), and enter the setup wizard to reset your route:

Note: If you want to dial up the Internet, choose PPPOE in the Internet mode, and enter your dial-up account and password (so that the router will help you dial the number, you don't need to use it, don't dial again), step by step, one of the steps is to set your wireless network name (SSID) and password, and this choice encryption method (preferably WPA WPA2), to prevent people from using your network, and the last step is to press save and press restart.

Look at your manual, it's not difficult, the above settings are correct, all your devices can be dialed up through the wireless router through the wireless router, regardless of whether they are wired (whether they are connected to the cat or not) or wireless.