After the wireless router is set up, the WAN port is 0!

This is caused by the failure of the router dial-up and the failure to obtain the valid IP address assigned by the operator, which shows that the obtained address is in the WAN port status, and the first thing to determine when this fault occurs is whether the fault point is on the operator's network or the router on the LAN.

1. Set up the dial-up connection according to the requirements of the operator, and connect the stand-alone device to the operator's optical modem and other equipment to dial-up the Internet. Doing a factory reset of your router and then setting it up again can troubleshoot. If you still can't get the address, you can only change the router.

2. If the stand-alone optical modem dial-up does not obtain a valid address, it is judged that the operator's network is faulty, and you can only call ** to find the operator's maintenance staff for on-site maintenance.

There are several possibilities, one is that network operators prohibit multiple front-line terminals, such as Tietong, etc., which have some restrictions. The second is the online account, if you use the cat, the operator's cat only needs to fill in the account number and password, and the complete account needs you to consult, for example, ABCD is the account number, and the telecommunications may be, or it may be the ** number 12345678, then the account number is specifically needed to consult the customer service of the online business. There is no specific network business information, there is really no way to explain clearly, optical fiber is another category, the use of equipment is different, the specific situation depends on the type of broadband you open, if it is the kind of shared network speed, it is very troublesome to set up routing.

Online providers add some restrictions, and you are almost not allowed to use routing. Oh.

1. Connect the operator's incoming line to the cat.

2. From the cat to the WAN port of the Leike router, which is the WAN port router, if you can't see clearly, find the only interface with different colors in the back interface.

3. There are factory default settings on the back of the router, write down the IP address, username and password.

4. Connect the computer to the LAN port of the router with a network cable.

5. Open the computer browser, enter the router IP address you just wrote down in the browser address bar, and enter the user name and password.

6. After successful login, you can see the status of the current router, and the setting wizard will pop up when you log in to the router for the first time. Follow the wizard prompts to set up, the basic step is to choose the broadband access mode, generally PPPoE (that is, broadband dial-up Internet access), and fill in the username and password provided by the operator. If it is connected by someone else's network cable, choose the method of automatically obtaining (dynamic address).

7. The next thing is to set the SSID (that is, the WiFi name) and password of the wifi, that is, the name of the wifi to be connected to the mobile phone and the wifi password that needs to be entered. The rest can be left unset. Nowadays, many routers have anti-rubbing network function, and you don't have to bother to change it, as long as you ensure the strength of the wifi password, try not to set a password of pure numbers or pure English words.

8. If the above steps are done correctly, but you still can't access the Internet, call the operator to report the repair line.

It depends on your access method, if you connect to the cat, then you need to set up PPPOE dial-up Internet access, and fill in your Internet account and password in the WAN settings, if it is assigned IP, you can directly set up dynamic IP access. And is the network cable of your router connected correctly?

Broadband connection account password is inaccurate, or the wiring is inaccurate, the wiring is poor, and the wireless router is faulty.

Re-restore your routing to factory settings in Reconnect look.

Is it finally set up, pro?

1. If you look at all the router logs, it may be that the account password is wrong.

The setting method is very simple, as long as you read the manual clearly, you can know how your broadband is accessed, there are generally three kinds: virtual dialing, automatic IP allocation, fixed IP (static), and then follow the instructions on the manual step by step, to put it simply:

1.Connect the LAN port of the router with the computer network card, and set the IP address on the NIC to be in the same network segment as the router.

3.Set network parameters: (take virtual dialing as an example).

Internet access: ADSL Virtual Dialing (PPPoE).

In the information box, enter the ads account.

Password: The login password provided by the operator.

Wireless parameter setting: it can not be moved, but also can set the password, switch, etc.;

Internet access is available at all LAN ports and Wi-Fi.

If you use the Internet in the other two ways, you need to set the information of the WAN port.

We are the same brand of router,I'm in the same situation as you now.,Newly bought,The first day is good.,The second day it's exactly the same as your situation.,WAN connection status is always in the connection,Is this brand of router this problem?

LZ: The cat you use must be the kind sent by Telecom.

You can take a look at your cat.

There should be a wifi logo on the back, as well as an account number.

These are custom cats.

You don't have full permissions.

So you can't get on.

There is also the wrong password of your broadband account and password.

Solution: Confirm the password of the broadband account from the new.

Buy a non-custom cat.

You try to use the IE browser to enter, in addition, you can't plug the incoming line from the cat into the WAN port of the router, this is the incoming line from the cat must be inserted into the WAN port of the router, otherwise you can't use wireless Internet access.

1. Confirm that you are connected to the wireless network. Find the wireless network connection in Control Panel - Network and Internet - Network Connection.

2. Right-click on the wireless network connection - status.

3. The details of the midpoint of the wireless network status, which contains the default gateway. It is the IP that logs in to the background of the router.

Check the LAN port of your router for your computer's network cable, don't plug it in by mistake.

The possible cause is a problem with the computer:

1. The wireless network card of the notebook is not installed with a driver or the driver is incorrect;

2. The IP setting of the notebook is incorrect;

Solution: 1. Right-click "My Computer" - Device Manager, and in the window on the right, check whether the wireless network card is installed.

2. If the driver is incorrect, you can uninstall it and reinstall it.

3. Go to "Network Connection" to check the IP settings of the wireless network.

1) Right-click on "Network" -- Properties -- Change adapter settings. Once entered, right-click on "Wi-Fi" and click on Properties.

2) The "Wireless Network Properties" option pops up, double-click "Internet Protocol Version 6" on the page that appears, and check "Automatically get IPv6 address".

4. If the above methods still cannot connect to the network, please check whether the connection between the router and the cat is normal or reset the network.

Step 1: First of all, you need to connect to the corresponding router via WiFi;

Step 2: Check the instructions label on the back of the router and find the IP and default username and password.

Step 3: Open the browser and type "http: ip" and press enter.

Step 4: Enter your username and password in the pop-up page, and you can enter the router interface.

Step 5: Enter the setup wizard interface;

Step 6: Choose the Internet access method: PPPoE;

Step 7: Enter the corresponding account and password (given by the business office) for the broadband;

Step 8: Set the username and password for the wireless connection of the router, click "Save";

Step 9: Find the wireless information directly on the computer, enter the password to surf the Internet.

It may be due to the following conditions:

1) There is a problem with the broadband that provides wifi hotspots, you can try to connect the computer alone;

2) If the broadband is normal, it may be caused by the wifi setting problem, you can reset the wireless network to try to connect;

3) There is a problem with the wireless network card, you can try to reinstall the driver.

Can you confirm that your network provider is giving you PPPOE dial-up Internet access? Call your dealer, if it's a PPPOE, ask them to repair it. Are you sure that the cable that can access the Internet is plugged into the WAN side of the router? If so, please repair it.

Thank you for your question.

The easiest way is to set the MAC address and clone it!!

The optical modem can be connected directly to the computer and can access the Internet, indicating that the optical fiber broadband is completely normal.

The router connection fails to get online, either the router is damaged or there is a problem with the router settings.

Look**, first of all, I suspect that there is a problem with the setup, because it seems that PPPoE virtual dial-up is selected, which is not used in fiber broadband.

If you are white, you can reset the router directly, and you can access the Internet by default. Reset to play, remember to add wifi password.

Try cloning or restoring your Mac address from the factory.

If it doesn't work, check whether the line is connected normally.

Since you can open this page, it means that your computer has been trained to the router, whether it is wireless or wired, in short, you are connected.

What do you mean by no signal?

Is it not possible to access the Internet?

You look at the above figure your WAN status is not connected, the WAN port is the port you connect to the Internet, are you using ADSL to surf the Internet? You need to select the PPPoE item in the WAN configuration, instead of the dynamic IP, fill in your broadband username and password in the PPPoE, and then connect, the router is connected to the Internet, and your computer can access the Internet. After the connection, the IP and DNS in the WAN status will be displayed.

It's better to go to the people who sell this thing.

<>Step 2: Open the browser and enter; The user's password is guest.

Step 3: Enter the route and click on the Quick Configuration Wizard:

<>5. Since mine is not a wireless router, you can set the wireless password.

Finally, click Finish to save, and if you see that it is connected, you can surf the Internet.

Note: Once you've used routing, your computer no longer needs to dial up.

Click on the external network configuration, select the Internet dial-up method as pppoe Enter the username of your broadband 3032 and password, click OK, and then click on the interface information for 5 seconds, see the WAN line information, IP address, these are not for but a string of numbers, which means that you have successfully dialed, and the computer can open the web page directly, and you don't need to dial again.

I look at your routing settings, and I don't know if you were able to access the Internet before.

If you can get on, then there is something wrong with your static IP.

If this problem occurs when the router is reset, it is not set up.

Here's how to set up your wireless router:

1. The broadband bus (the network cable from the cat) connects to the WAN port of the router.

2. Connect one end of the network cable to any LAN port of the router, and connect the other end to the computer, and start the computer and router equipment;

3. After starting the device, open the browser and enter it in the address bar to enter the wireless router settings interface.

4. An account and password to log in to the router appear in the settings interface, enter the default account and password admin

5. According to the setup wizard step by step, select the Internet mode, usually ADSL users choose the first PPPOE, if you use other network service providers, choose the following two according to the actual situation, if you don't know that.

How to choose, directly select the first item to automatically select, which is convenient for novices to operate, and click next after selection;

6. Enter the account and password applied for from the network service provider, and go directly to the next step after the input is completed;

7. Set the wifi password, try to make the alphanumeric combination more complicated and not easy to be rubbed off the network.

8. After entering correctly, it will prompt whether to restart the router, select Yes to confirm the restart of the router, and you can access the Internet normally after restarting the router.

Check if there is a problem with the cable and the 2 ports that the router connects to the demodulator.