The optical drive cannot be accessed, and the prompt function is incorrect

<>2. After the program runs, directly double-click the disk that needs to recover data.

3. After the program finds out the data, it will be placed in the same directory as the label of the disk to be recovered.

4. Check the data to be recovered, right-click and select "Copy Checked Files", and the software will copy the checked files.

5. Just wait for the software to copy the data.

1. First of all, you need to click the [Start] button at the bottom left of the screen"Run"window, enter the letter as shown in the figure below and press the enter key.

2. Next, it pops up on the desktop"services"Settings window, click to open the third option.

3. After entering the interface, click [Startup Type], select the option of [Disable] and do not leave, and then click [OK].

4. Next, you need to restart the computer to operate: double-click the selected desktop to open it"Computers"option, and then select the sub-selection drive in the Properties screen.

5. Finally, you only need to check it"Launch CD recording on this device"to complete the setup for this computer. Then turn on the drive again and you're ready to go.

1. Open the "Run" dialog box, enter: , click OK to open the "Service" dialog box;

2. Find "imapi cd-burning com service" in the "Service (Local)" list (as shown below).

3. Double-click the imapi cd-burning com service to open its properties dialog box, and change the "startup type" to "automatic". (as shown below).

4. Restart the system to save the settings, right-click in the explorer after restarting, and the "CD Drive" item will appear in the "Send to" menu at this time.

Because after the system has installed Nero, the CD burning function of Windows is disabled.

Click Start Running, Enter, Open Service, Double-click on the imapi cd-burning com service service, change the startup type to Automatic, Restart.

Turn on My Computer, open the burner's drive properties, and in the Burn tab, check Enable CD recording on this device.

In addition, if the recorder and hard disk are using the same cable, or if two recorders are installed, the above problems can also occur. It is recommended that you use a separate cable for the recorder and hard disk. If it is a dual recorder, then because Windows can only be turned on for one of them"Desktop CD recording", the other is in the non-open state, put the burning disc in the non-open state, it will not automatically activate nero, double click to enter will prompt the function is incorrect, as long as it is selected on the non-open state"Enable CD recording on this device"Can.

3. Select the "Settings" tab, tick the "Disabled" checkbox, then select "All Drives" in the "Turn off Auto" box, click the "OK" button, and exit the "Group Policy" window. This is the method on the Internet, but I chose it without configuration, and it will be good after choosing, so you can try it!

Cause of failure: Because the built-in CD burning function is blocked after the system is installed with Nero Express.

Solution: 1. Use the shortcut key "win+r" to turn on"Run"window, enter and click OK.

2. Eject"services"In the Settings window, locate the imapi cd-burning com services project.

3. Double-click to change the startup type to Automatic, and click OK.

4. Restart the computer and open it"Computers"Options, select the Properties option of the drive.

5. Check it later"Launch CD recording on this device"The setup is complete, and the blank disc is ready to use.

Is there a problem with the burned system disk? Isn't the optical drive broken!?Reinstall the burning software. There are generally problems with the system on the Internet**. Let's try it on the virtual machine first. It feels good to burn again.

There are about two reasons for your situation, one is that the disc itself is a blank disk, that is, the disc to be written, in the XP and below systems, the blank disc in the state of pending writing cannot be read, and trying to open it will prompt that it cannot be accessed and the function is incorrect.

On the other hand, it may be that your optical drive itself cannot read this disc or that the disc is corrupted;

For example, if you are a CD-RW CD-ROM drive, you will naturally not be able to read the ***-r CD, and it will report an error or not respond when you open it

If the disc itself is polished, or there is an error when burning, it may also be opened with an error.

Cause of failure: Because the built-in CD burning function is blocked after the system is installed with Nero Express.

Solution: 1. Use the shortcut key "win+r" to turn on"Run"window, enter and click OK.

2. Eject"services"In the Settings window, locate the imapi cd-burning com services project.

3. Double-click to change the startup type to Automatic, and click OK.

4. Restart the computer and open it"Computers"Options, select the Properties option of the drive.

5. Check it later"Launch CD recording on this device"The setup is complete, and the blank disc is ready to use.

After the imapi cd-burning com services are launched, you will also need to enter the command to disable the CD burning function.

Problem Description:

Widnws XP directly opens a blank burning disc through the recorder and prompts "Unable to access......The function is incorrect. ", right-click on the property and show zero free space?

Cause of the failure: This is because the built-in CD burning function is blocked after Nero Express is installed on the system.

Solution: Step 1: Open it in the system"Run", enter, and one pops up after OK"services"In the settings window, find the imapi cd-burning com services project, double-click on the project, change the startup type from disabled to automatic, and restart the system after confirmation.

Step 2: Open"My computer", select the burner's drive properties, and in the burn tab, put it"Launch CD recording on this device"Tick the box and re-insert the blank disc, and it will be displayed normally.

Step 1: Open it under the system"Run", enter, and one pops up after OK"services"In the settings window, find the imapi cd-burning com services project, double-click on the project, change the startup type from disabled to automatic, and restart the system after confirmation.

Step 2: Right-click"My computer", Properties, Hardware, First, select the burner's drive properties, and in the Burn tab, put"Launch CD recording on this device"Tick the box and re-insert the blank disc, and it will be displayed normally. Some people on the Internet say no, but I can do it, it varies from person to person...

。。。You open a blank disc and of course the function is displayed incorrectly.

Burning is done in the burning software and does not require you to open the disc.

Then it's useless for you to open the disc, not to mention that the blank one can't be opened.

It's something wrong with some of the system's settings. Here's how to fix it:

First workaround:

Step 1: Open it under the system"Run", enter, and one pops up after OK"services"In the settings window, find the imapi cd-burning com services project, double-click on the project, change the startup type from disabled to automatic, and restart the system after confirmation.

Step 2: Open"My computer", select the burner's drive properties, and in the burn tab, put it"Launch CD recording on this device"Tick the box and re-insert the blank disc, and it will be displayed normally.

Second workaround:

1. Switch to another account to enter (note that the switch is not a logout, if there is no other account, please go to the control panel - create a credit account);

2. Open the disc after entering from another account, there is no prompt of "the function is incorrect", and you can view the used and remaining space of the disc;

3. Switch the account to the account where you have an optical drive error prompt, open the disc and there will be no "function incorrect" prompt, and everything will be done after restarting.

The third workaround:

Uninstall the optical drive in Device Manager, then go to the control panel to add new hardware, and re-drive, if it works properly, it is a hardware driver problem.

Step 1: "Control Panel" - Performance and Maintenance - Management Tools - Services", find "imapi cd-burning com service", click to open this item, change "Startup Type" to "Automatic", and change "Service Status" to "Startup". Then start the service.

Step 2: Start Group Policy in "Start" - Run "Input", then "Manage Templates" under "User Configuration" - Windows Components, click "Windows Explorer", find "Delete CD Burning Function" on the right side of the panel, click to enter this item, and click "Disabled" under "Settings".

Step 3: Disable the optical drive in "My Computer" --Properties", and then enable the corresponding optical drive.

I'll copy you a solution address, dear.

The solution to the prompt "Unable to access g: The function is incorrect" when opening the disc icon Optical Storage Hardware Tutorial Script Home.