When decorating tiles, whether the insulation material should be removed

Need to remove, if the insulation material is not shoveled off, directly paste the tile, the tile will be easy to fall off in the later stage, and the insulation material must be removed before the tile is pasted. If the wall tiles are not shoveled off, the construction bricks will fall off. Falling wall tiles can cause unnecessary damage.

The correct way to do this is to shovel off the insulation and remove the anchors that hold the insulation in place. The walls are chiseled and brushed with glue and then tiled. Because it is a sealed balcony, there is no need to keep the wall insulation layer.

It is also recommended to use double-layer insulating glass for sealing the balcony glass, so that the indoor thermal insulation coefficient is better, and do not use general glass in order to save hundreds of pieces. After all, it's home, so you have to think about it.

Thermal insulation materials are generally materials with a guiding thermal coefficient less than or equal to. Thermal insulation materials are developing rapidly, and the use of good thermal insulation technology and materials in industry and construction can often achieve twice the result with half the effort. For every ton of mineral wool insulation used in construction, one ton of oil can be saved a year.

Personally, I don't think there is a need to remove:1Can keep warm 2If you remove it, the outer layer of paint will be destroyed (exterior paint can be waterproofed).

Is it the ground? Or the wall, the insulation material should not be removed.

1. First of all, it is necessary to determine the position of the insulation wall and the specific thickness of the insulation material, and use the method of full laying cement board to enhance the wall strength of the insulation wall.

2. According to the actual condition of the wall, it is necessary to determine whether to use a single-layer cement board to reinforce or a double-layer cement board to reinforce, and in some cases it is necessary to install a light steel keel.

3. Ensure that the size of the expansion plug into the wall should be deep enough to ensure that the expansion plug has been firmly embedded in the wall.

4. Properly handle the gap between the two cement slabs, and it is best to fill the gap with cement. In order to ensure the firmness of the tiling, it is best to hang a metal mesh on the surface of the cement board to increase the fineness of the bond between the cement and the wall.

5. When reinforcing the insulation wall, the quality of building materials such as cement, light steel keel and expansion plug used in the bond defense must be guaranteed to be superior, otherwise it will easily affect the solidity of the wall in the future.

1. The insulation layer should be constructed according to the specifications, such as hot-dip galvanized steel wire mesh, the thickness of the anti-cracking mortar should be above, and the surface of the extruded plastic board should be brushed with interface agent.

2. Paper bricks, strip bricks and other small bricks are directly pasted with tile adhesives, and stone bricks should be fixed with anchor bolts or hung dry.

3. The external thermal insulation project of the external wall should not use pasted facing bricks as the finishing layer; When adopted, its safety and durability must meet the design requirements. The exterior wall insulation can be as blue as blue to use lightweight dry-hanging exterior wall insulation decoration composite hanging board decoration, which adopts dry-hanging installation process and uses riveting fasteners.

The construction process of ceramic tiles on the insulation wall is:

Wet the balcony wall first.

Then use polymer cement mortar to paste the polystyrene board to the wall, and after pasting it to dry thoroughly (24 hours can be done, preferably 48 hours), a thin layer of polymer cement mortar is applied to the polystyrene board. Then immediately lay the alkali-resistant nylon mesh or metal mesh on the polystyrene board, and then apply a layer of polymer cement mortar. The thickness can be about 1cm.

The metal mesh needs to be thicker because the area is larger, and all parts of the metal mesh cannot be tightly attached to the polystyrene board. After 24 hours, you can apply the tiles.

4.Tile can be applied with polymer cement mortar, or with ordinary cement, if tile adhesive is used. Then the previous process is to pay attention to leveling when plastering polymer cement mortar on nylon mesh or metal mesh.

5.Generally, polymer cement mortar is used to paste tiles. One is that the paste is firm, and the other is to save the trouble of buying ordinary cement and sand, or tile paste.

Note: In addition to tiling, polymer cement mortar must be used in other processes, not ordinary cement. Because the polymer cement mortar already contains rubber powder, its adhesion is greater than that of ordinary cement.

The plastering layer outside the insulation layer should be equipped with a grid, a special mortar as a base, and then an ordinary mortar (as thick as possible). Scrape the tile adhesive before sticking the bricks.

Ceramic tiles account for a relatively large part of the decoration area, therefore, on the façade, the impact is crucial, but many times, we neglect maintenance, or in the maintenance of the door, resulting in the tiles that can be used for decades quickly crack and warp or even fall off, today I will teach you how to maintain tiles in daily life!

1. Dish soap, soap, etc. can be used for daily cleaning of ceramic tiles.

2. If there are tea, coffee, beer, ice cream, grease and other pollutants attached to the surface of the tile, it should be scrubbed in time, and sodium hydroxide or potassium bicarbonate solution can be used to stain it if necessary. Ink, cement and other pollutants can use diluted solutions of hydrochloric acid and nitric acid, while paint, paint and other pollutants are best used special cleaners.

3. Clean the tiles with a mixture of soap and a little ammonia and turpentine, which can make the tiles cleaner and brighter.

4. Polished tiles should be waxed regularly, ceramic tiles: once every 23 months. The gaps between the bricks can be cleaned with paste from time to time, and then a layer of waterproofing agent can be brushed on the cracks with sheep's hair, which can prevent mold growth.

5. If there are a few slight scratches on the brick surface, you can apply toothpaste to the scratches and wipe them vigorously with a soft dry cloth to repair them. If the damage is serious, it should be replaced in time or repaired by professionals to avoid personal injury.

In fact, there is no need to do special maintenance!

Nowadays, there are a lot of tile cleaners, and a lot of caulks will be sold.

However, if you want to maintain it, you should pay attention to the following points:

1. Keep the dryness of the tiles, high-grade tiles will not be affected by air humidity, mainly cement and other auxiliary materials!

2. The killer of oil, furniture, and electrical appliances, of course, is also one of the sources of scourge of tiles.

It's okay to keep the underside of the hood clean all the time!

3. The bathroom, the bathroom is the easiest place to get dirty and the most used, so keeping the bathroom ventilated and equipped with common dirt treatment agents is the king!

4, living room, dining room, this is nothing to pay attention to, 2 days to sweep, 5 days to drag enough.

5. Don't let sharp weapons, heavy objects suddenly touch the tiles, no matter how good the tiles can be immunized several times, but they can't control often!