How can I get back to normal if the camera gets into water?

What you should not do is to turn on the camera immediately to see if it is damaged, and you press the switch to turn on the circuit, and if water has entered the camera, it will short-circuit, and the integrated module and device will be burned. The problem is serious, as long as you quickly take out the battery, use a cotton cloth to absorb the water in the camera, and then put it in a ventilated place to let it dry naturally, there will generally be no problem. Now you can only dry it with a hair dryer and cool breeze to see if it is restored, or send it for repair.

Whether it's just a blown fuse, so that ** won't be very expensive.

Hehe, I tried to take a photo when I got into the water, I was anxious enough, but unfortunately I couldn't eat hot tofu in a hurry, and now I can only see your luck. Do not perform any operations on electronic products that have been ingress with water, including turning them on and off, before removing the battery.

Take out the battery immediately and put it in a ventilated place to let the water evaporate, otherwise it will directly affect the service life;

If there is water in it and it is still working with electricity, it may directly burn out the camera.

The first step, such as upstairs.

The second step is to find after-sales service.

If you are using a Huawei phone, it is recommended that you turn off your mobile phone and bring the relevant proof of purchase to a nearby Huawei customer service center for maintenance. You can check the address of a nearby Huawei Customer Service Center on the Huawei website.

Precautions after water and liquid ingress in the mobile phone:

1.Do not move or shake your phone frequently after water is ingress to avoid moisture spreading inside the phone.

2.Do not use a hair dryer or bake at high temperatures (including microwave heating) after water is in, to avoid liquid being blown into the phone and the heat damaging the phone.

3.Mobile phones are made of delicate electronic components, and there is a potential risk after water ingress, so please keep your phone turned off.

4.If you don't have a backup of your data, there may be a risk of data loss during repairs. After you go to the Huawei Customer Service Center, you can consult with a staff member to help you evaluate whether you can back up your data.

First of all, do not turn on or off, take out the camera's battery and SD card, and use a hair dryer to blow hot air into the camera to let the water evaporate.

No matter what kind of camera you are, if you fall into the water, the first thing you need to do is not to check whether it can still be turned on and used, and the wiring inside the boot will be short-circuited after entering the water, which means that it will be scrapped directly.

1. The worst result is that the entire machine is scrapped.

Regardless of whether the camera is turned on or not, the main part of the camera can burn out, usually with a 90% chance because there is residual power in the camera or flash, and it will break when water enters it.

2. The metal part of the shutter group of the camera is prone to rust.

3. The motherboard of the camera is also susceptible to corrosion.

5. After the lens gets into the water, it is easy to get moldy. If it is not cleaned up in time, it may also produce water mist in the lens, which will affect the normal shooting.

Shut down immediately. Put it in a cool and ventilated place, dry it slowly, and do not expose it to the sun. If it can't be turned on or there are other faults after drying, you can only find the after-sales maintenance department for inspection and maintenance.

Hello, after the camera enters the water, it must be in a natural environment at this time, or use some hair dryer to dry it, which will be more appropriate, don't turn on the machine immediately, it is easy to burn the motherboard circuit when you turn it on, and then you can see if it can be used and put it in the rice cylinder to absorb moisture.

If there is water, put it in a cool place, turn it off, wait for three or four days, turn it on again, and if there is a problem, go to the repair shop.

1. Generally, there are two situations of water ingress into the camera: splashing liquid and water ingress into the whole machine; The incoming liquids are also divided into several cases: seawater, fresh water, and other liquids such as beverages, etc.

If the camera confirms that water has entered, no matter what kind of liquid, the power supply should be cut off immediately to prevent the circuit from burning out. If the camera is turned off, the first thing you need to do is remove the battery. If the camera is splashed with fresh water (mineral water or tap water), the camera can be placed in a dry and ventilated place for at least one day, and then powered on for functional check, if it can be used normally, but it should be stored in moisture-proof; If there is an abnormal situation, cut off the power immediately and send it to the local maintenance station for maintenance.

Usually we recommend that you put it under a light heat source such as a desk lamp or spotlight to let the water dissipate slowly. This process takes more than eight to ten hours, and do not rush to use a strong heat source such as a hair dryer to get directly close to the camera, which will cause serious aging of the circuit and even deformation of the shell and circuit board. Don't try to turn on or charge the camera until it's completely dry, sometimes waiting is an effort!

2. If the camera enters seawater, drinks or serious water into the whole machine, it should be sent to the maintenance station immediately for treatment, there is nothing to hesitate, time is the life of your camera. Because seawater and beverages have strong corrosiveness to the circuit board of the camera and the metal parts in the camera, if not treated in time, the prognosis of the camera is not optimistic, and in serious cases, it will cause the camera to be scrapped, and it will not be repaired even if it costs money.

3. After the maintenance of the camera with water, because the liquid that enters the camera chip and the metallization hole of the circuit board cannot be removed, if it is damp, it will continue to produce rust, and the lens is also prone to mildew after being damp. Generally insist on 3-5 months, in addition to these situations, what may also happen is that the rain pours into the camera, because sometimes when you go out to shoot, it is inevitable that you will encounter rainy days, especially in the south, a heavy rain is coming, and you can't hide if you want to, what should you do at this time? Because the air pollution is already very serious, the rainwater is no longer single, in addition to the water may also contain some acidic substances, so it is more troublesome to deal with, and using a hair dryer or a desk lamp to dry can only be a drop in the bucket, because the digital camera is composed of a combination of parts and equipment, some internal data cable interfaces, due to the principle of capillaries, the rainwater can not be evaporated, on the contrary, evaporation will make the acid and alkali concentration of those liquids higher and higher, and the corrosion at the motherboard interface is becoming more and more serious. In this case, the camera is usually fine after the initial blow drying, but in the following period, the camera is good and bad, and some strange symptoms will appear one after another, and finally it will not turn on at all.

Summary. Kiss the camera water treatment method:

Kiss the camera water treatment method:

1. The best way is to take out the battery immediately to power off the camera and prevent the motherboard and circuit from burning out. Don't leave the camera to chance, in case the camera is damaged even more.

2. Pour out the water to prevent the water from remaining in the camera and lens to corrode the equipment.

3. Send it to the professional camera maintenance department as soon as possible and clean it with professional cleaning materials in time.

Kiss Note 1: Do not disassemble and assemble by yourself.

2: The emergency method of using a hair dryer to dry is not advisable and cannot solve the practical problem at all. Just because the camera surface is dry doesn't mean that the water-damaged area won't corrode.

Hope it helps<>

1. Cut off the power of the camera and do not try to turn it on.

2. Wipe off visible water stains on the body (or blow properly with a hair dryer) and find a case that can hold the camera.

3. Lay a layer of rice in the box and place the camera bayonet facing down.

4. Pour in rice grains to cover the fuselage, about one inch higher than the height of the fuselage.

5. Close the lid and leave it for a week to start the machine.

Of course, this practice has a certain chance to make your SLR rebound, and it can also save you a lot of maintenance costs.