Envision sticks what car film ratio is better, and I am about to pick up the car

Hello Dragon Film, Master Film, 3m Ray-Ban are all available.

The film should not only choose regular products, but also pay attention to the construction process of the car film. Because the effect of the film depends largely on the application process.

1. In order to avoid dust and impurities affecting the effect of the film, the body glass should be cleaned first before the car film.

2. The parts that may be damaged during the car film should be covered in advance to prevent scratching the car paint, interior and other parts; Accessories that may affect construction also need to be disassembled in advance.

3. After the overall treatment of the car body, it is necessary to start cutting the car film, and the car film should be preliminarily cut according to the size of the glass.

4. Paste the roughly cut car film on the car glass, and then the front and rear gears need to bake the film according to the amplitude of the car glass, and the effect is to make the amplitude of the car film close to the glass, so that the car film will be flat and free of water marks.

5. After baking, the film will be very obediently attached to the glass, and then it is necessary to make further corrections, that is, according to the shape of the glass, the corresponding shape will be finely cut.

6. The glass film is pasted inside, so the key step is to put on the film, and the requirement of the upper mold is to clean the inside of the glass, which is fast and accurate, and pushes out the moisture as soon as possible.

7. After all the work is done, the last need to do an inspection work, after the whole vehicle is pasted, the situation of each window should be checked, especially the corners, and the blistering phenomenon should be dealt with immediately.

Reminder: After the film, it is required that the window cannot be opened for 2-5 days, the rear gear cannot use the defogging function, and the front windshield cannot use the air conditioner to blow the air; Do not use toothed objects to scratch the glass; After the construction is completed, the warranty application form must be filled in, so that the after-sales service in the future can be guaranteed; After 3 days of car film, it is best to go back to the store for a re-inspection, and if there is any quality problem, it should be repaired in time.

Need. The benefits of car film are also obvious (the quality of the film referred to here), which can insulate light and heat, prevent bursting, and have obvious effects on safety and comfort.

Autotintfilm is a film-like object attached to the front and rear windshields, side windows and sunroofs of the vehicle, and this film-like object is also called solar film or heat insulation film. Working principle: Through vacuum spraying or magnetron sputtering technology, aluminum, gold, copper, silver and other metals are made into multi-layer high-insulating metal film layers with silver land to denseness.

When irradiated by light waves, the electric field of the light waves causes the free electrons to absorb the energy of the light, and produces an oscillation of the same frequency as the light, which in turn emits light at the same frequency as the original light, which is called light reflection.

Its function is mainly to block ultraviolet rays, block part of the heat and prevent the occurrence of injuries and anti-glare caused by glass splashing, and at the same time, according to the one-way perspective performance of the solar film, to achieve the purpose of protecting personal privacy. In addition, it can also reduce the damage caused by ultraviolet radiation of items and personnel in the car, reduce the temperature in the car through physical reflection, and reduce the use of car air conditioning, thereby reducing fuel consumption and saving some expenses.

It needs to be filmed, a high-quality car film, which can isolate light and heat, prevent punctures, and have obvious effects on safety and comfort.

Automotive film is also called heat insulation film or solar film. As you can know from the name, the biggest use of car film is heat insulation and anti-ultraviolet rays, and it can also reduce air energy consumption to a certain extent. The material of the car film is a polyester layer, which is transparent and has a certain impact resistance, which can block the impact and reduce external damage to a large extent under a certain external impact.

The car film also ensures a certain degree of privacy in the empty room in the car. Usually a car with a car film is difficult to see clearly from the outside, but it can be seen clearly from the outside.

When choosing to apply film to the car, do not choose an inferior film that is too low because of the reputation, because the inferior film is likely to bring counterproductive results to the driver and passengers. When distinguishing the car film, Tuqiao can observe the color of the car film, whether there is a peculiar smell, whether it feels thick and smooth, etc. And you can also choose according to the specific indicators of the car film.

It is best to choose big brands and high-quality automotive films, such as 3M, Johnson & Johnson, Dragon Film, Shu Ruojia, Kangde Xin, etc. Different brands and different grades of car films** vary greatly. Please choose a car film that suits your needs according to your personal needs, such as better light transmittance, better heat insulation, and higher cost performance.

Millions of car purchase subsidies.

Need. The benefits of car film are also obvious (here it is said that the combustion bureau is a qualified quality film), which can not only isolate light and heat, but also prevent punctures, which has an obvious effect on safety and comfort.

Automobile coloring film is a layer of film on the front and rear windshields, side windows and sunroofs of automobiles, which is also called sun film or heat insulation film. Working principle: Using vacuum spraying or magnetron sputtering technology, aluminum, gold, copper, silver and other metals are made into multi-layer to dense high-insulation metal films.

Shell electrons (free electrons) in metals are generally not bound by the nucleus. When irradiated by light waves, the electric field of the hidden mountain of light waves causes free electrons to absorb the energy of light, producing oscillations at the same frequency as light, and this oscillation emits light at the same frequency as the original light, which is called light reflection.

Its main function is to block ultraviolet rays, block part of the heat, prevent damage caused by glass splashing, prevent glare, etc. At the same time, according to the one-way perspective performance of the solar film, the purpose of protecting personal privacy is achieved. In addition, it can also reduce the damage of ultraviolet radiation to the objects and people in the car through physical reflection, reduce the temperature in the car, and reduce the use of the car air switch, thereby reducing fuel consumption and saving some expenses.

Millions of car purchase subsidies.

Envision whole car film** is about 3000 yuan:

1. In order to avoid gray reeds and impurities affecting the effect of the film, the body glass should be cleaned first before the car film, and the parts that may be damaged during the car film should be covered in advance to prevent scratching the car paint, interior and other parts; Accessories that may affect construction also need to be disassembled in advance.

2. After the overall treatment of the car body, it is necessary to start cutting the car film, and the car film should be preliminarily cut according to the size of the glass. The rough cut car film is pasted on the car glass, and then the front and rear windshields need to be baked according to the amplitude of the car glass, and the effect is to make the amplitude of the car film close to the glass, so that the car film will be flat and without water marks;

3. After baking, the film will be very obediently attached to the glass, and then it is necessary to make further corrections, that is, according to the shape of the glass, the corresponding shape will be finely cut;

4. The glass film is pasted inside, so the key step is to put the film on it, and the requirement of the upper mold is to clean the inside of the glass, which is fast and accurate, and pushes out the water as soon as possible;

5. After all the work is done, the final need to do an inspection work, after the whole vehicle is pasted, the situation of each window should be checked, especially the corners, and the blistering phenomenon should be dealt with immediately.

Millions of car purchase subsidies.