What are the items required for car film, and what steps are required for car film?

Generally, junior technicians can only apply film to the side windows, while only intermediate and senior technicians can apply film to the front windshield with a large curvature.

Before the film, it is necessary to check whether the installation of the window glass is intact and the integrity of the car glass to ensure that the subsequent film work can operate normally.

Be sure to cover the necessary parts of the car before applying the film to prevent liquid from penetrating. Sprayed cleaning fluids and lubricating fluids can affect trim parts such as automotive electronics and interior seats.

Wash the interior and exterior surfaces of the windows before applying the film (focusing on the interior surfaces and glass sealant areas). This is mainly to eliminate the dirt or other object construction quality problems between the heat insulation film and the window glass after the film, and ensure that the film and glass can be perfectly combined.

The membrane is pre-cut. Use a ruler to measure the size of the front and rear windshields, and cut the film according to the measured size. (The professional film mechanism is through the computer, which is tailored according to the model).

Spray the installation fluid. Dust spots can be avoided and corrosion at the edges can be reduced, resulting in the desired viscosity and better application results.

Dry roasting, wet roasting shaping. The film is dry-roasted first so that the film can be fully pre-shrunk. In order to further improve the adhesion of the heat insulation film, it is also necessary to wet bake and shape the heat insulation film.

Extrusion of the installation fluid: In the process of using the wiper to remove the installation fluid, try to scrape the installation fluid between the heat insulation film and the window glass, which can reduce the drying time of the heat insulation film and obtain a better bonding effect, overall performance and visual effect.

Check after sticking. "Three looks and one attention": look at the entire heat insulation film to see if there is any dust and bubbles, see whether the corners are firmly glued, and sit in the car to see if there are any places that affect the line of sight (especially the front windshield and side windshield). After the film, it is recommended not to raise or lower the glass arbitrarily within 48 hours.

The most important thing to pay attention to when applying the film is the use of hair dryer, if you blow this place for a long time, it will cause the glass to crack due to uneven heating. Therefore, it is necessary to find those professional authorized stores for the film, so that the quality of the film will be the best and the danger of glass cracking can be avoided.

Also, the car film is best in rainy weather, and when it is pasted on rainy days, there is very little dust in the air, which has certain benefits for aesthetics.

Northern Lights Solar Film is here to help!!

1. Brand: The first choice is the 5 popular brands, Weigu, 3M, Johnson & Johnson, Dragon Film, and Quantum Film.

2. Type: In the case of sufficient budget, nano-ceramic membrane is preferred.

3. Parameters: The light transmittance is greater than 70%, the heat insulation rate is greater than 30%, the ultraviolet blocking rate is greater than 98%, and the internal reflectivity is less than 10%, and the longer the warranty period, the better.

Depending on the demand, the front baffle film, the side baffle film, and the rear baffle film are generally these three, and the front baffle can also be omitted.

With the fire in the car detailing industry, many car owners will beautify their cars. Among them, the film is the choice of many car owners, so what are the steps of professional car film? What are the precautions?

Precautions for professional film car 1. If the sun is sufficient, the glass cannot be lifted or lowered within three days. If it's a rainy day, you can't lift the glass for a week!

2.Do not start the demisting heating wire within 30 days after the car film. 3.

If there are blisters on the edge of the membrane, the owner should drive the owner to the construction site for repair within 24 hours. 4.Do not attach any inhaled items to the film for 30 days after the car wrap.

5.Do not apply any adhesive labels directly to the film. The electrostatic stickers in the store can be used as annual inspection labels.

6.After the film, if the fog between the film and the glass is normal, the owner does not have to worry, and it will dry naturally in 1-2 months. 7.

The front shield is behind the membrane, and the defogging air outlet of the front shield shall not blow air on the front windshield within a week.

Professional Car Wrap StepsTools and ingredients for professional wrapping include car wrap creation mode installation fluid, scissors, utility knives, grill guns, scrapers, bath towels and chair covers, deerskin towels, and cotton cloths. Steps:1.

Spread two large bath towels on the front cover and instrument of the car, cover the seat cover, and wrap it tightly with plastic wrap to prevent pollution. Every glass in the car must be thoroughly cleaned, especially the top of the glass. 3. Spray a small amount of window film liquid on the outer surface of the window glass, and then gently cover it with a soft mold.

After carefully sliding the positioning, cut. Pay attention to the cutting operation, and the car film must be firmly attached to the glass. Then cut the window film according to the mold.

4. Apply the window film installation fluid evenly to the glass again.

Film. Since basically all window glass is not completely flat, the window film can be precisely shrunk and shaped on the composite curved surface of most windows by means of a baking gun. This eliminates wrinkles on the surface.

6. After the exterior window is filmed, the next step is the internal film. Just like the exterior window, spray the film solution evenly before applying the film. 7. After determining the final position of each layer of window film, the installation fluid should be evenly sprayed on the surface of the window film to lubricate its surface.

After that, gently rinse with a plastic spatula in the triangle. 8Finally, use a cotton cloth to carefully suck out the water squeezed out of the window. The film is finished.

Bian Xiao concluded: Now, all car owners should know how to apply movies. Of course, you can try it yourself, but Bian Xiao recommends going to the shop in 4s, where it is more professional!

1.Shielding and protecting the body and important parts of the car: This is mainly for the front windshield film, which covers the front of the car and the dashboard and seats in the car with a protective cover. Side glazing also needs to shade the inside and outside of the vehicle.

2.Window cleaning: Clean the interior and exterior surfaces of the windows, focusing on the interior trim and glass sealant areas.

3.Cutting and cutting film: Now there are automatic film cutting and manual measurement film, and some directly meet the model specifications of the finished film does not need to be cut.

4.Glass glass film: The glass film is generally composed of 3 layers of film, and the outer two layers of film are useless, just to protect the inner film.

After tearing off the protective film and spraying the installation fluid on the adhesive surface of the window film, the inner surface of the glass is also sprayed with the installation fluid, and after installing and moving the window film, remove all air bubbles and as much installation fluid as possible.

5.Inspection: Check the air bubbles and moisture in the car film, check the corners and other parts that are easy to ignore, and when it comes to the front windshield, be sure to sit in the car to observe the light, visibility, etc.

1. External cleaning: When the car is filmed, it is necessary to clean the glass of the car, move it in the clockwise direction, clean each piece of glass of the car, pay attention to the corners of the car glass, and make preparations to achieve better results in the film. 2. Contour cutting:

A small amount of window film is sprayed on the outer surface of the window glass.

First of all, you need to clean the surface of the car, and use a hair dryer to remove all the moisture, then wrap the glass, then cut the film to the right size, stick it to the car, and then use a towel to drive out the bubbles in the film, and then use a lighter to close the edges, and that's it.

First, it is necessary to clean the glass, spray a small amount of installation liquid on the surface of the glass block, cover the window film on it, and cut the window film along the border; Instead, a portable hot gun is used to accurately and typically shrink the car model; The third is to tear off the protective film, after sliding positioning, spray the installation fluid again, and discharge the installation fluid with a professional water squeezing tool.

Clean the body and keep it dry. 2. Determine the location that needs to be pasted. Under normal circumstances, slowly apply while scraping flat with a tool and removing the bottom paper.

3. If the graphics are really not big, you can also tear off all the transparent transfer film and stickers before pasting. But care must be taken not to accidentally adhesion.

4. After pasting, scrape and press several times. Remove the transparent transfer membrane.

5. Draw a knife with a utility knife on the door and sewing the car, and wrap it inward. Rowing Sparrows.

Main advantages: The automotive film is a vacuum thermal evaporation film, which adopts a vacuum thermal evaporation process, which evaporates the aluminum layer on the substrate to achieve the thermal insulation effect. This is also commonly referred to as the field of mammoto metal film, which has a relatively long-lasting thermal insulation, but the weakness is that the clarity is not high, which affects the comfort of the field of vision, and another prominent weakness is the high reflection.

1. Before applying the car film, you need to clean the glass, because if the car glass is not cleaned, it will become blurry after the car film is pasted, which will not only affect the appearance, but also affect the quality of the film. Cleaning the glass is as simple as cleaning it with clean water and then scrubbing the belt repeatedly with a scraper plate. In order to ensure that it can be cleaned, it is best to wash it several times.

2. Prepare a glass sample of empty potatoes, measure the size, and then cut the car film to the appropriate size of the bucket walker.

3. Cover the car film cut to the appropriate size on the outside of the glass, and use a scraper to stick the car film tightly to set the shape.

4. Tear off the liner after setting the type, and then stick the car film on the inside of the glass. After pasting, spray water on the back of the car film, and then use a scraper to scrape out the water.

5. After completing the above steps, carry out the final inspection, such as to see if there are air bubbles, etc., if there is no problem after the inspection, then the car film is pasted.

Car film mainly refers to the car glass film, which can block ultraviolet rays and heat insulation, but the poor will also affect the line of sight, and some local regulations do not allow the sun film to be too dark, and the light transmittance is too low to be conducive to driving safety.

The role of car film can be roughly divided into the following points:

1. Blocking heat and ultraviolet radiation, automotive film can resist 99% of harmful ultraviolet radiation. Protect the skin and interior trim from damage, so that the driver and passengers are not exposed to the sun; And the high-quality car film can reflect infrared rays, so that the temperature in the closed car is much lower than the outside world, effectively reducing the frequency and time of air conditioning, and saving gasoline.

2.With good clarity and transparency, the high-quality car film can weaken the strong glare reflection of the headlights shining on the rearview mirror when driving at night, making it very comfortable for the eyes. In addition, it has a good line of sight in rainy days, when reversing, and when turning around.

From a safety point of view, this is one of the most outstanding properties of automotive films.

3.Explosion-proof and anti-robbery automotive film can effectively prevent personal injury caused by the splashing of glass fragments, improve explosion-proof performance, and make theft more difficult.

4.To prevent scratches on the surface and keep a clear visionThe outermost layer of the high-quality automotive film is the anti-scratch layer, that is, to ensure that its own surface is not scratched under normal use and keep the field of vision clear, so as to improve the safety of driving.

5.The car film that protects privacy also has one-way light transmission, which can ensure the privacy of passengers.

Summary: It is recommended to pick up this kind of film yourself, and you still have to choose those with a better reputation, just like Meiji, I still prefer Meiji, and finally I still advise you, really don't buy inferior car film, it is no different from naked running, and it costs money in vain.