Is it better to have all porcelain floor tiles or all over tiles?

1. The surface of the all-porcelain floor tiles is polished, although it is said to be relatively bright, but the pattern is single, compared with the all-glazed tiles, etc., it is far behind. Because the full glazed tile is not limited by the technical aspects in terms of brick design, and the texture is not the same, it is relatively rich. However, in comparison, all-over bricks.

The color is more single, and consumers have less room to choose when purchasing.

2. The production process is compared with the production process of full-body bricks, which are mainly made by pressing the powder of clay and stone by pressing and then firing. It looks like the color of the front and back is the same, no glaze, after firing, the surface is polished, so that the front is smooth and beautiful, and the back is the original appearance of the brick. In the production process of all-ceramic floor tiles, the specific process is the same as that of polishing tiles.

Similar, but the production requirements are higher, requiring a better press, able to suppress higher densities, and at the same time firing at a higher temperature. In other words, all-ceramic floor tiles are strengthened polished tiles, and the surface is generally very bright when it no longer needs to be polished. Of course, from the point of view, because the production process of all-ceramic floor tiles is more complicated, it is also much more expensive than full-body tiles.

3. The color of all-ceramic tiles is relatively single, there is no big change, and the difference between the various colors of the brick surface will not be too strong, but the whole brick is not the same, and the color of the all-ceramic tile is richer than that of all-ceramic tile. The whole brick is glazed after printing the pattern, the color should be more vivid, and it is completely unrestricted, red, black, yellow, blue, blue and purple are no problem at all.

1. What is a full-body brick?

The whole brick is a wear-resistant brick, also known as unglazed brick, and the material color of the front and back is the same. Common full-body brick products include wear-resistant bricks, polished bricks, antique bricks, square bricks, supermarket bricks, exterior wall tiles, etc., which are used for indoor and outdoor wall and ground decoration. The surface of the whole brick is not glazed, the effect of decoration is antique, elegant and chic, simple and natural, and because its surface is very rough, the light is irradiated to produce diffuse reflection, the reflection is soft and not dazzling, and it will not cause light pollution to the surrounding environment.

2. What is an all-ceramic tile?

All-porcelain floor tile refers to the water absorption rate is less than or equal to the porcelain glass fossil, which is made of quartz sand and mud fired in a certain proportion, and then polished with an abrasive tool to polish the bright, the surface is as translucent and smooth as a mirror, which belongs to the category of full-body bricks. In addition, the water absorption rate of vitrified tiles is less than or equal to, and it belongs to full ceramic tiles. Under the condition of a certain pressure and temperature, the ceramic embryo body of the final kiln is also coated with an impermeable water layer behind the ceramic tiles, even if the whole brick is immersed in water, it will not enter the water.

3. How about all-ceramic tiles?

The color of the all-ceramic tile is bright and soft, and there is no obvious color difference as a whole; High-temperature sintering and complete porcelain generation of mullite and other crystals, so the physical and chemical properties are stable, corrosion resistance, and anti-fouling performance; The thickness is relatively thin, the bending strength is high, the brick is very light, and the load of the building is reduced; No harmful elements are added; High bending strength and low water absorption.

However, due to the water absorption rate of all-ceramic tiles, the density is very high, and the hardness is high, resulting in the cement is easy to stick, so it can not be used as wall tiles, but can only be used for filling the ground.

What are all-ceramic floor tiles?

All-ceramic floor tile refers to the porcelain glass fossil with water absorption less than or equal to, which is fired from quartz sand and mud in a certain proportion, and then polished with an abrasive tool to make it bright, and the surface is as translucent and smooth as a mirror, which belongs to the category of full-body bricks. In addition, the water absorption rate of vitrified tiles is less than or equal to, which belongs to all ceramic tiles. Under the condition of a certain pressure and temperature, the ceramic embryo body of the final kiln is coated with an impermeable water layer behind the ceramic tiles, even if the entire brick is immersed in water, it will not enter the water.

What are the advantages and disadvantages of all-ceramic floor tiles?

Advantages: 1. The color of the all-ceramic floor tiles is bright and soft, and there is no obvious color difference as a whole.

2. High-temperature sintering and complete porcelain form a variety of crystals such as mullite, so the physical and chemical properties are stable, corrosion resistance and stain resistance are strong.

3. The thickness is relatively thin, the flexural strength is high, the brick body is lightweight, and the load of the building is reduced.

4. No harmful elements are added; High flexural strength and low water absorption.

Disadvantages: However, due to the characteristics of low water absorption, high density and high hardness of all-ceramic floor tiles, it is easy to cause cement to stick, so it can not be used as wall tiles, and can only be used for filling the ground.

Full tile and all-over tile are not terms of one dimension and cannot be compared.

Full tile refers to the tile with less water absorption, and the general household floor tiles are ceramic tiles.

The whole brick is a non-metallic organic matter (rock chips, slag, clay, etc.) pressed by high temperature, the surface is not glazed, most of the time the positive and negative materials and color of the same ceramic tiles, because of its rough surface, good anti-skid performance, most of the anti-skid bricks on the market belong to the whole body bricks, widely used in exterior walls, aisles, outdoor walkways and other places.

In fact, I think it's better to have a whole body tile, because the quality of such a tile is particularly good, and there will also be a particularly good brightness, so the effect of such a tile is very good, so the effect presented is also very good.

**Different, polished bricks and full-body bricks are also different in terms of size, polished bricks are mainly used in the living room lamp, the size is generally a large floor tile, and the full-body brick is often 300 * 300 small floor tiles.

When decorating, it is believed that floor tiles and wall tiles are the same and can be used together, but in fact, this is very unsafe and not very scientific. So, what is the difference between floor tiles and wall tiles? Let's introduce the difference between floor tiles and wall tiles.

1. The difference between floor tiles and wall tiles.

1. The water absorption rate of floor tiles and wall tiles is different.

Strictly speaking, wall tiles belong to pottery, while floor tiles belong to porcelain products, their essence and physical properties are different, whether it is from the selection of clay ingredients or to the firing process are very different. Generally, the water absorption rate of wall tiles is about 10%, which is several times higher than that of floor tiles with a water absorption rate of only 1%.

2. The place of use is different.

Generally, floor tiles are laid on the floor of bathrooms and kitchens, because of its low water absorption, so that bathrooms and kitchens will not be affected by water vapor and are less likely to absorb stains. The wall tiles are made of glazed pottery, with high moisture content, so its back is usually rough, so it is conducive to pasting the wall tiles with adhesives, and the floor tiles are not firmly pasted on the wall, and the wall tiles are used on the ground because they absorb more water and become difficult to clean, so the two can not be mixed.

3. Pay attention to the laying sequence.

Because the floor tiles are pasted from the inside out, if the ground has a slope or a floor drain, attention should be paid to arranging the water direction to find the slope; The wall tiles are paved from the bottom up, and for aesthetic reasons, the bottom bricks should be pasted last.

Second, the precautions for laying wall tiles and floor tiles.

1. Before preparing to paste tiles, the base should be cleaned up at the grassroots level, such as lime plaster, latex paint, wallpaper and other decorations on the wall, or dirt on the ground, etc., which must be cleaned up, otherwise the cement mortar will not be firmly bonded with the base layer; If there are cracks in the wall itself, it should be properly treated before tiling.

2. After the wall tiles are pasted, the floor tiles should be pressed again, and if there is a situation where half a brick appears, it should be placed at the bottom as much as possible. In addition, when pasting wall tiles, one wall can not be pasted to the top at one time, so that the tiles are prone to collapse.

All-over tiles are also known as all-over tiles. The whole brick is fired from cuttings pressed under high pressure. After surface polishing, its hardness is comparable to that of stone.

The water absorption rate of the whole body brick is low and the wear resistance is good. The surface of the brick is not glazed, and the material and color of the front and back are the same, hence the name. Although there are still varieties such as seepage tiles, relatively speaking, their colors are not as good as glazed tiles. Most of the anti-slip bricks belong to open bricks.

Compared with porcelain tiles and full-body tiles, porcelain bricks are slightly better than full-body marble.

Porcelain throwing bricks and all-over marble are suitable for living room floor tiles, if you want to wear a little better, then choose porcelain throwing bricks, if you take into account the cost performance, the whole body marble is cheaper, it is recommended that buyers choose according to their actual use and cost budget. Porcelain throwing brick and all-over marble are two different categories of poor closed stoves, as ceramic tiles, both are suitable for the decoration of the living room of the home.

Porcelain throwing brick is the whole body of the color and culture, that is, the texture of the interior and the texture of the exterior are the same, can achieve the decorative effect of natural marble bricks. From the point of view of performance and decorative effect, porcelain throwing brick is slightly better than the whole body marble, but it is also a lot more expensive, so buyers choose according to their actual use and cost.

The difference between porcelain throwing tile and all-over marble

1. The performance is different.

The advantages of porcelain throwing bricks are good color rendering, low water absorption, high wear resistance, long service life and reliable quality. All-over marble is a little worse in terms of performance.

2. **Different.

The ** of normal porcelain throwing bricks is much higher than the whole body marble, if you encounter two kinds of ** almost, you must be careful about its authenticity.

3. Different colors.

The glazed brick of the porcelain brick, the ultra-white body, the glaze of the whole marble tile and the embryo body are consistent.

Summary. The all-over bricks are good. The all-body drill has the advantages of wear resistance, high slip resistance and high hardness.

The surface of the all-body diamond is not glazed, so the outside is antique, very elegant and exquisite, very suitable for retro-style home decoration, because the outer surface of the whole body brick is not smooth, it is relatively rough, so the reflection of light will be very weak, will not reflect, so the light hits the above is softer, will not cause light pollution, very suitable for use in the living room, bedroom and other places. The hardness of the whole brick is also very strong, so the wear resistance is very high.

The all-over bricks are good. The all-body drill has the advantages of wear resistance, high slip resistance and high hardness. The surface of the whole body drill is not glazed, so the outside is antique, very elegant and exquisite, very suitable for retro style home town Yuting decoration, because the outer surface of the whole body brick is not smooth, is relatively rough, so the reflection of light will be very weak, will not reflect, so the light hits the above is softer, will not cause light pollution, very suitable for the living room, bedroom and other places to excite.

The hardness of Tongzheng Brigade sock body brick is also very strong, so the wear resistance is very high.

Tips for choosing the quality of tiles.

First, look at the appearance. The color of the tile should be uniform, the surface finish and flatness should be good, the surrounding rules should be regular, the pattern is complete, and four or five pieces should be extracted from a box to see if there are defects such as color difference, deformation, lack of edges and corners. 2. Listen to the sound.

Lao Hongluo struck with a trembling hard object, the crisper the sound, the higher the degree of porcelainization, and the better the quality. You can also use the thumb, index finger and middle finger of the left hand to clip the corner of the tile, hang down easily, and tap the middle and lower part of the tile with the index finger of the right hand. 3. Drip test.

You can drop water on the back of the tile to see how fast the water soaks after it spreads, generally speaking, the slower the water absorption, the greater the density of the tile; On the contrary, the faster the water absorption, the sparse density, and its intrinsic quality is superior. Fourth, the measurement. The higher the accuracy of the side length of the living room tile, the better the effect after paving, and buying high-quality tiles is not only easy to construct, but also can save man-hours and accessories.

Use a tape measure to measure whether there is a difference in the size of each tile, and the high accuracy is the top grade.

Hello, I am glad to be able to solve your problem, clear the closed for you to analyze the porcelain throwing bricks to answer the luck crack better. The specific reasons are as follows: full-body brick is a kind of quiet building material, with strong thermal performance, can effectively protect the indoor temperature, good durability, can resist harsh climate, long service life, but high, installation is more complex, easy to lag the construction progress.

Porcelain throwing brick is an economical building material, with good thermal performance, can effectively protect the indoor temperature, good durability, can resist harsh climate, but low, simple installation, easy to meet the construction schedule, but easy to damp, easy to deform and discolor. In general, porcelain throwing bricks is better.

First of all, determine the difference between the two, and judge that the first can be distinguished according to two points, 1. Check whether the color of the surface of the tile is consistent with the bottom of the billet, referred to as "look"; 2. Drip test, the water absorption rate of ceramic tiles is determined, and the water absorption rate of full ceramic tiles and full-body bricks needs to be less than or equal to. Therefore, whether it is a full-body tile can be judged according to whether the material and color of the front and back of the tile are consistent.

Advantages and disadvantages of each:

All ceramic tiles are actually vitrified tiles. Advantages: Its surface is smooth and translucent, so there is no problem of polishing pores. Rich in colors, disadvantages: easy to dirty, anti-slip performance is not as strong as the whole brick.

Advantages of all-body bricks:

Due to the rough surface, the wear resistance and slip resistance are the best of all ceramic tiles.

Disadvantages: Its unique structure determines the texture and effect of the whole brick, and the decorative effect is poor.

There is a certain difference between the full ceramic tile and the whole body tile in the size of the specification, the whole porcelain tile is mainly used in the living room, the size is generally the large floor tile, and the whole body tile is often 300 small floor tiles.

2. Different colors.

The color of the whole tile is relatively single, there is no excessive change, and the various colors of the brick surface have a small jump. The color of the whole body brick is richer than that of the whole tile, it is glazed after the pattern is printed, the color is more vivid, and it is completely unrestricted, basically all kinds of common colors can be made.

3. The lines are different.

The texture of the whole tile and the whole brick is not the same, the texture of the whole tile is larger, and the texture of the whole brick is smaller as a whole.