2700hg d cat with router, want to go wireless, can t tune, please

1.Your local connection is set up, the most important thing is that the DNS needs to be right for the same IP segment! Otherwise, if you fill in the DNS that is not your local area, you will not be able to access the Internet.

2.In the wireless cat router (the dialer is not set, the connection mode is) wireless, you can not set the encryption first. You look at the clear wireless configuration is very simple, my wireless settings should be ticked, if there is a wire can be on, it means that your cat router wireless module is broken or your wireless network card is broken!

Mode: IEEE Only IEEE Only Mixed (Channel Gap: 100 ms.)

RF Switch: Tick.

Wireless channels: 13

TX Rate: 54Mbps

tx Power: 100%.

SSID-1 enables: Tick.

Wireless Name (SSID): chinanet-QoS type: WMM

This is my wireless cat router.

The easiest way is for you to take a phone with wireless Internet access (Wi-Fi0 to try it on your computer network card is broken!). Can't go on the wireless modem routing is bad, or set the wrong (you have to ask the person you bought which values are wrong to fill in the Internet, one I've already told you, and I don't know if you have an MTU value is under the broadband password).

It's not too clear for the time being, but there is a chance for us hi to chat.

There's nothing to argue about, and it's wrong to connect your cat in this way before, unless your cat is a cat with a routing function, otherwise you can use it that should be you or use a broadband connection on the computer, which means that the router only plays the role of a separator, you must know that the basic function of the router is to replace the dialer on the computer, so you don't need to use a broadband connection on the computer after using the router, and you can connect to the network directly through the local connection, That is, the computer is turned on and connected to the network. So you have to make it clear whether you want to use a broadband connection when you are not using the router, if you don't want it to be a routing modem, then it is okay to connect to the LAN port, you just need to enter the router and turn off DHCP, and set the wireless name and password on the wireless router. Tip: You can set up the router first and then connect the network cable, otherwise you will enter the previous routing modem.

If you need to use a broadband connection, then you need to connect to the WAN port of the router, and then connect it to the computer from one of the LAN ports, after entering the router, you only need to open the setup wizard on the left, select the PPPoe method, fill in the Internet account and password, and the name and password in the wireless settings.

The LAN of the cat is connected to the WAN of the router and is set in the Router Management interface.

Reset the router:

1.Change this バイ ground connection to self.

Du moves to get the IP address.

2.Plug in the wireless router DAO back.

electricity, don't connect the "cat" (modem modem answer), reset the wireless router (restore to the factory), connect the computer to any "lan" port of the wireless router, enter the settings page, and set it according to the PPPoe (ADSL virtual dialing) method. Then set the SSID, encryption method, and password. Save, restart.

After setting up, connect the network cable from the "cat" to the "WAN" port of the wireless router.

This is not possible, your modem's LAN port needs to be connected to the router's WAN port, unless your cat is a routing modem.

There will be no additional cost, if you have a router, then you have to set up the router first, the main thing is to set the parameters of the router's WAN port, including your Internet account and password, as long as you set it, your computer's IP address is automatically obtained, and then you can access the Internet, no longer need to dial on the computer.

Note: Some ISPs restrict the use of routers.

Write the IP address inside the router (that's pretty much what it means). There will be no additional cost for using the cat directly to access the Internet.

First of all, there is no additional charge for connecting the cat to the computer to access the Internet.

Secondly, the description of your problem is not clear, please tell you the brand and model of the wireless router, and whether you have set up wireless Internet access, etc.

First of all, you need to know whether your router has the function of wireless Internet access;

If you have, chances are you didn't turn on the wireless and turn it on;

And in the end, it could be that the wireless device might be broken, like a broken filament in an antenna, or something like that, but that's pretty hard.

The route is not set up. Just set it up again.

There will be no additional fees (if you get an account with the ISP department).

Dialing is OK, and the cat and the computer can also be set to connect at one time, and there is no need to dial the number when it is turned on.

If so, you need to set the WAN port of the wireless router to dynamic IP mode, change the IP address of the LAN port, turn on the DHCP service, and save. Finally, plug the original network cable into the WAN port of the wireless router.

Units of fiber? That means that your network cable is split from your company's switch or router. If it's a router, it's easy to do, but if the switch has permission, it can't do anything.

The fiber per unit indicates that there are many users, and it is generally a switch, if you want to use routing, as the upstairs said, there is permission, and you can't do anything.

As long as the optical fiber is accessed, it is necessary to use the optical modem to convert it into a network cable signal, and then you can access the Internet wirelessly through the wireless routing setting, the specific operation is as follows:

1) Connect the router and enter the address you see on the router in the browser, which is usually.

2) Then enter, enter the corresponding account and password, generally the new ones are admin.

3) After entering the operation interface, there is a setting wizard on the left, and the attack enters (generally it pops up automatically).

4) Enter the setup wizard interface, click Next, enter the Internet mode setting, you can see that there are three Internet access options, if it is dial-up, then use PPPoE. Dynamic IP can be used by plugging the computer directly into the network, and there is a DHCP server on the upper layer; The static IP is generally a private line or something, or it may be a cell bandwidth, etc., and the upper layer does not have a DHCP server, or wants to fix the IP.

5) Select PPPoe dial-up Internet access to fill in the Internet account and password, and then enter the wireless settings after the next step, and enter the next step after setting the wireless account and password;

Look at the broadband access method of your home, because the resources of each place are different, the situation is also different, after applying for broadband, if your home is the first line resource, it is ADSL, it is needed ordinary cat, if it is ftth, that is, fiber to the home, then you need optical modem. But if it is FTTB, that is, fiber to the corridor, also called Ethernet, this does not need to use a cat, because the Ethernet device has converted the signal in the weak current well, as long as you plug in the network cable and enter the broadband account password.

Wireless network card. There is also a WLAN hotspot that comes with the mobile phone, which is equivalent to a wireless router and can be connected to a 3G network.

Whether a mobile phone can access the Internet wirelessly depends on whether the router transmits wireless network information. You know, it's hard for a good woman to cook without rice. If your network is entered by ** line, your router is useless without cats.

Neither your phone nor your wired desktop can access the internet. If your network is directly connected by LAN (i.e., network cable), you don't need a cat, as long as the connection is correct, the settings are appropriate, and you have the wireless transmission function, you will be able to access the Internet.

You first figure out what a router is and what a cat is.

The cat is a modem, a ** line, or an optical fiber, or a wired access to the "dialer" with a cat to connect to the Internet.

In general, the cat is only a function to access the network (except for the two-in-one mode of the cat and the router).

A router is a device that shares your network with multiple computers, or mobile phones. Generally, it does not have the function of accessing the network (except for the two-in-one model of the cat and the router).

So you only have a router without a cat, there is no way to connect to the network at all, and of course you can't access the Internet. (except for the cat and router two-in-one).

No, you need to use a wireless router.

In the order you say. The WAN port of Router 2 is connected to the modem, and the WAN port of Router 1 is connected to the LAN port of Router 2. The LAN port of Router 1 is connected to the computer. That's it.

Isn't it right for you to connect?,Router 1 or 2 is a WAN to connect to the cat,And the other router is to use the WAN port to connect to the router with the cat,So that you can surf the Internet。

Are you asking how to connect a cat wirelessly with a laptop?

1. Turn on the wireless switch on the cat, and the WLAN light is on right2. Turn on the wireless switch on the notebook, and there is a wireless connection icon in the lower right corner3. Select the signal of your cat on the notebook, and connect (there may be a key, which is written on the back of the cat).

Each brand has a different approach, take a look at the manual!

3G card, but it's best not to use desktops, not to mention stuck, your traffic will be on the high side.