How to open the back cover of Huawei Honor V10 to change the battery?

If you are using a Huawei phone, it is not recommended to disassemble the phone without permission, so as not to damage other parts of your phone, which may affect the warranty service. If your phone has a problem and needs to be repaired, it is recommended that you back up the data in your phone in advance (WeChat QQ and other data must be backed up separately) and bring the warranty certificate to a nearby Huawei Customer Service Center for repair

1. Open the service app through your mobile phone > More > of Quick Service Click to repair at the shop > Select a city Enter the address, or open the service app > the nearby service store at the bottom of the service interface.

2. Log in to Huawei Consumer Service from your computer** > Service Support in the navigation bar> drop-down page > Service Store Query > Enter Province, City, County, and District.

10 is an all-in-one machine. The steps to open the back cover are as follows:

Insert the card pinhole with the card pin, and then withdraw the card tray. Then use a fingernail or a flat plastic tool to slowly pry open each bayonet from the bottom end of the phone and along the edge seams.

Remove the back cover afterward. Then unscrew the corresponding bead screw, remove the bead, and tear off the electric tape.

I have seen others repair the kind of mobile phone that can't open the back cover to replace the battery, and there is a heating machine that first heats the phone to 100 degrees, and then slowly pries open the parts. Then take out the battery, do some soldering, and put on a new battery. Then add the wind-curing glue,。。

Wait half an hour...

The cost is about 100 yuan.

Go to the Internet to search for maintenance tips, use warps, instrument screwdrivers and other tools.

Now they are all non-removable back shells, and there is no strong DIY ability, so don't easily repair your phone.

The battery of this phone is not a convenient type to replace, so please go to a future service center to replace it.

Isn't this an all-in-one machine? If it's an all-in-one machine, I suggest that you better not open it yourself, it's easy to be damaged.

This situation depends on whether you will repair it, if you can't repair it yourself, then you had better go to the mobile phone store to change the original battery to save the wiring.

This is an all-in-one machine, you need to unscrew each small screw, it is not recommended to disassemble and assemble it yourself.

How to disassemble Huawei Honor V10? There are many curious friends who want to see how the interior of the Honor V10 works, or the phone is broken and want to take it apart and take a look at it yourself, so how to disassemble the Huawei Honor V10? Let's take a look!

Preparation steps for disassembly.

Dismantling tools: screwdrivers, suction cups, tweezers, plastic paddles, built-in clips, etc.

Honor V10 motherboard teardown.

Honor V10The interior adopts a common three-stage blind balance design,Before disassembling the motherboard,First remove the fixed grinding screws on the motherboard,Then power off,Then disconnect the cable connected to the motherboard,As shown in the figure below。

Dismantle the small board at the bottom of the Honor V10.

After removing the top core plate, the next step is to remove the bottom board, and still remove the fixing screws first, as shown in the figure below.

Dismantling experience From the point of view of the whole process of disassembly,GloryV10It is still good in terms of workmanship,Delay the skin continues the solid workmanship level of the big factory,The inside of the mobile phone performs well in space utilization,Connector protection and anti-collision ability,And in terms of heat dissipation capacity,Sealing compared with Huaweimate10Series flagship It seems to be decent,But from the point of view of **cheap thousand yuan,Obviously, it is also very acceptable。

Glory V10 Antutu running score how much ]

Honor v10 how to restore factory settings ]

It is not recommended to disassemble the phone without permission, so as not to damage other parts of your mobile phone, which will affect the warranty service. If there is a problem with your phone, it is recommended that you bring the purchase receipt to the local Huawei after-sales service center for inspection and repair. The following describes how to query the address information of the Huawei Customer Service Center:

2. You can also have an after-sales outlet query address entrance at the bottom of the official website page of Huawei**;

Huawei Glory10Inch full screen,Equipped with Kirin970Processor,There are6GB+64GB128GB storage combination options,Battery capacity3400mAh,Next,Let's look at its internal structure with Brother Xiuping。

Turn on step-by-step reading mode.

Tool materials: Honor 10 mobile phone, card needle, suction cup, preat, screwdriver, tweezers, warping rod, etc.

How it works: Turn off the Honor 10 mobile phone first, and then use the card pin to take out the card tray.

After removing the card tray, use a heat gun or hair dryer to heat the back of the Honor 10 phone, and then use the suction cup tool and the pick blade to scratch the back cover left and right from the gap to open the back cover.

Once the separation is complete, we can see a sheet of heatsink graphite attached to it, revealing it.

Unscrew the cable fixing baffle screws for a total of 3, and then remove the baffle.

Next, disconnect the power connector, then disconnect the display cable connector and the sub board connector, and the coaxial cable on the right side should also be disconnected.

Unscrew the remaining screws on the motherboard, a total of 6.

Remove the front and rear camera platens, then disconnect the camera cable and remove the camera.

After the above steps are done, we can easily take out the motherboard.

The next disassembly is the bottom of the fuselage, first unscrew the screws at the bottom of the fuselage, a total of 7 screws, and then remove the speaker module.

Finally, disconnect the fingerprint recognition module connector, motherboard cable connector, and coaxial cable, take out the subboard, and disassemble the machine.

Special Tips. Be careful when disassembling the back shell, do not disassemble it hard, so as not to disassemble the back shell and deform.

You need to have a tool, first heat the back cover evenly, then use the suction cup to pull out a gap, and then use a pry plate to carefully pry open the back cover.