What should I do if the indicator light does not light up after changing the filter element of the Q

1. Check whether there is a power outage: If there is a power outage, the power supply cannot be turned on, and the water purifier cannot produce water, so you need to wait for the power to be restored before turning it back on.

2. Check whether the low-voltage switch is out of order: the low-voltage switch is out of order, the overvoltage is displayed, the protection device is started, and the water purifier automatically stops making water, and the switch needs to be repaired to eliminate the fault.

3. Check whether the water level controller is out of order: If the water level controller is abnormal, the water purifier will also fail to produce water, and a new water level controller needs to be replaced.

4. Check whether the computer box is faulty: the computer box is faulty, and the water purifier cannot make water, the easiest way is to replace the computer box with a new one to eliminate the fault.

The filter element of the Qinyuan drinking machine is generally on, and it will flash when it needs to be replaced, and you can press and hold the reset button for 5 seconds after replacing the filter element.

Analysis of common faults of Qinyuan water purifier.

1. Frequent start-up cannot be stopped.

If the water tank is full of water indicator light and will be off, you can open the main engine door, check the high-voltage switch (black, marked), adjust the pressure adjustment screw clockwise, and observe whether it can be solved in the running state, if it is not solved; Please observe the pure water pressure gauge on the side of the host, when running, whether the pressure will rise and fall, if this phenomenon exists, it may be flushing leakage, in the running state, you can unplug the pipe at the flushing water end, observe whether there is water flowing out, if so, it is the flushing solenoid valve failure; If there is no above phenomenon, the reverse osmosis membrane shell check valve is leaking.

2. The pure water pump is started but cannot produce water.

Please observe the panel source water pressure indicator, if it is off, please check whether the municipal tap water is cut off or the water pressure is low; If the source water pressure lamp is always on, you can open the main door, unplug the pipe at the outlet end of the water inlet solenoid valve (blue, marked), and observe whether there is water flowing out of the outlet end of the solenoid valve (the pressure is large, please cover it with a towel); If there is, you can unplug the blue pipe of the ultrafiltration inlet (different models have different processes, and may not be connected to ultrafiltration, subject to the on-site model) to observe whether there is water outflow in the working state (the pressure is large, and the container needs to be used to receive water), if there is no water outflow, the water pump is blocked; If there is water coming out, it should be a blockage of the reverse osmosis membrane.

3. The panel water tank is full of water and the light is on, but there is no pure water flowing out.

You can shake the pressure bucket to see if there is water in the tank; If there is water, you can check the air valve at the bottom of the pressure bucket and press to see if there is any gas discharge, if not, the bucket is out of pressure and can be charged with 7psi pressure.

4. The pump starts and stops when it is running.

Unplug the blue pipe of the water inlet of the main engine on the side of the main engine, and observe whether the water outlet is too small (the pressure is large, and the container needs to be connected to the water), if so, the pretreatment filter element needs to be replaced; If the effluent is normal, check whether the source water pressure is low, and if so, a pressurization device needs to be installed; If the water pressure is normal, it should be affected by water hammer, and a water hammer elimination device needs to be installed.

5. The main engine cannot produce water if it does not start.

6. Check whether the power light of the host panel system is on, if not, check whether the power switch is turned on, whether the fuse of the power socket is fused, and if so, replace it; If the power indicator is on, check whether the water is off or the source water switch is not turned on; Check whether the panel water tank full water indicator is on, if it is always on, after checking that the water tank is empty, it should be a high-voltage switch failure; If the water tank is full and the indicator light is not on, it should be that the pretreatment filter element is blocked, resulting in the overload of the water pump and the inability to produce water, and the filter element needs to be replaced.

7. The quality of pure water and ultra-pure water exceeds the standard.

The pure water quality exceeds the standard, which is manifested as the conductivity exceeding the standard, which causes many reasons for the problem, which needs to be specifically analyzed, and can be inspected by our company's technical personnel or by the local office or dealer.

This is the reason why it is not reset well.

1. After installing the filter element, reset the indicator light of the replacement filter element according to the method on the manual, and let the selected corresponding filter element be recalculated.

2. After the filter element is just replaced, it needs to be flushed or drained with water, and the disinfectant in the filter element should be rinsed for about 15-30 minutes.

If you buy a Qinyuan modular water purifier, it has an intelligent control system, which monitors the use of water flow, displays the life of the filter element, and prompts the filter element to be replaced when the filter element is off when the life expires.

Zhejiang Qinyuan Water Treatment Technology Co., Ltd., as the core holding subsidiary of Qinyuan Group, is a high-tech enterprise specializing in the research and development, production and sales of a series of environmental protection products such as household water purification equipment, and regards "comprehensive drinking water solution service provider" as the future development direction of the enterprise.

The company has undertaken more than 20 national scientific research projects such as the National Torch Program Project and the National Key New Product Project, and has more than 300 international and domestic patents. In 2008, it passed the ISO9001:2000 and ISO14001:

2004 system certification.

The company has a complete marketing network system and information management system, from chain home appliance stores, department stores, building materials markets, business channels to Qinyuan stores at all levels, franchise stores, forming a sales channel with tens of thousands of terminal sales networks and distribution systems.

Select the fourth one, then press and hold to reset for 3 seconds, and you're good to go.

Qinyuan water machine changed a filter light or flashed, press the recovery button and did not respond, please instruct a move.

1. The installation of the filter element is not very correct. 2. The water purifier filter element light is on to prompt the user to replace the filter element, and it needs to be reset and recalculated after the replacement is completed. 3. The low-voltage switch fails, and the high-voltage switch or water level controller fails.

4. The pressure loss of the high-pressure pump, the blockage of the pre-filter element (there is no pure water and wastewater or the waste water is small), the check valve is blocked (there is wastewater, no pure water), and the solenoid valve fails and cannot be effectively opened.

Summary. Dear, the indicator light of the filter element does not light up after the filter element is replaced by the Qinyuan water purifier: there is no reason for resetting, the filter element is generally on, and it will flash when it needs to be replaced, and the filter element can be replaced by pressing and holding the reset button for 5 seconds.

Qinyuan water purifier filter element replacement: First of all, turn off the power to ensure safety. Then, with the help of a small tool, remove the filter barrel.

After removing it, pay attention to a small gasket, which is generally black. Replace the old filter cartridge and replace it with the new one.

What should I do if the indicator light does not light up after changing the filter element of the Qinyuan water purifier, and it does not light up when I press reset?

Dear, the indicator light of the filter element does not light up after the filter element is replaced by the Qinyuan water purifier: there is no reason for resetting, the filter element is generally on, and it will flash when it needs to be replaced, and the filter element can be replaced by pressing and holding the reset button for 5 seconds. Qinyuan water purifier filter element replacement:

First of all, turn off the power to ensure safety. Then, with the help of a small tool, remove the filter barrel. After removing it, pay attention to a small gasket, which is generally black.

Replace the old filter cartridge and replace it with the new one.

It's because it hasn't been reset.

After installation, press and hold the reset button for 5 seconds.

You can ask the master to come and get it.

Just get it right.

Ask about custom messages].

What should I do if the indicator light does not light up after changing the filter element of the Qinyuan water purifier, and it does not light up when I press reset?

What should I do if the indicator light does not light up after changing the filter element of the Qinyuan water purifier, and it does not light up when I press reset? Hello dear, the reason is that the user forgot to press the "reset" button after replacing the filter element, only after replacing the filter element, select the replaced filter element on the machine panel and press the "reset" button, the indicator light of the panel will return to normal, and re-monitor the service life of the filter element. The display of the water purifier does not light up, which is usually due to these reasons:

1. If the display is battery-powered, it is recommended to see if the battery is a little bit and whether the connection is normal. The indicator light of the filter element does not light up after the filter element is replaced by Qinyuan water purifier: because it is not reset, the filter element is generally on, and it will flash when it needs to be replaced, so replace the filter element.

If my answer is helpful to you, please give a thumbs up (in the lower left corner), I look forward to your like, your efforts are very important to me, and your support is also the motivation for my progress. Finally, I wish you good health and a good mood!

If the indicator light is still on after the filter element of the Qinyuan water purifier is replaced, it may be because it needs to be reset. You can try to long press the reset button on the water purifier, it usually takes about 5 seconds to complete the reset. If the indicator light is still on, you can try to turn off the power and restart the hall or contact after-sales service.

Please note that after replacing the filter element, you need to follow the requirements of the manual to ensure the normal use of the water purifier.

It may be because the replacement filter element is not installed correctly or the replaced filter element is not the original filter element of Qinyuan water purifier. It is recommended to re-check the installation position and direction of the filter element to ensure that it is installed correctly with a search difference. If the problem persists, it is recommended to contact the after-sales service center of Qinyuan water purifier for consultation and maintenance.

There may be several reasons why the light does not light up after the water purifier filter element is replaced:

Incorrect replacement of the filter element: The filter element of the water purifier needs to be installed in a certain direction or sequence. If it is not installed correctly, it may cause the Wild Collision indicator light to not light up. Therefore, it is necessary to carefully check the instruction manual of the water purifier to ensure that the filter element is replaced correctly.

Circuit fault: If the water purifier prompt light is still not on, you can check whether the circuit of the water purifier is faulty. At this time, you can try to restart the water purifier, or unplug the power cord and plug it back in to see if the indicator light can light up.

System failure: If none of the above methods can solve the problem, it may be that the system of the water purifier is malfunctioning. At this time, it is necessary to contact after-sales maintenance personnel for overhaul and repair.

To sum up, if the prompt light does not light up after the water purifier replaces the filter element, Split World Talk first needs to confirm that the filter element is replaced correctly, secondly, you can check whether the circuit is faulty, and finally you need to contact the after-sales maintenance personnel for maintenance.