My home is equipped with 2M broadband of telecommunications, and I want to use a wireless router, ma

First connect the access cable to the cat, and then connect one end of the network cable to the interface on the cat, and the other end is connected to a blue on the wireless router (generally blue, anyway, the hole that is different from the color of other holes), if it is a desktop, then use a network cable to connect the computer to the wireless router, the desktop will show that the local connection is connected, and now you need to change the IP address of the computer to the same network segment as the IP address of your router to start setting, general TP— link is to enter in the browser and press enter will jump to the settings interface,Run the setup wizard,Follow the prompts and it's OK,When there is a step, you have to choose pppoe,The password should be set, otherwise people will steal your network。 After setting, it's OK, your laptop or mobile phone can be received, and you can surf the Internet, of course, you can also use your mobile phone, but others can also get it.

If you want to use wireless routing on your desktop.

There are two ways.

1.Buy a network cable, and the wireless router also has a socket.

2.Give your desktop a wireless card.

It's the same as a normal router.

Set up the router first: Go to the router to set a password, and then turn on the wireless network.

Then there is wiring: the telecom first comes out--- the WAN port of the router, and then the LAN port is connected to the computer.

The wireless router also has a socket, and you can connect it directly to the computer with a Category 5 cable.

There are so many equipment 150 will not be given, just buy a 300m on the line, no matter how high it is, it doesn't matter, the house is not duplex. The network speed is related to the bandwidth of the broadband, and the wireless router can only set the signal strength, so it is recommended not to use it through the load-bearing wall.

As long as you need 3 antennas, the rate of 350m and above has good wall penetration.

How many floors?

TP-Link is a good brand for wireless routers.

If your house is tall, it's a good idea to get a router on each floor.

Routes can be set as follows:

The network cable behind the dial-up modem is connected to the access entrance of the wireless router, and the network cable exit after the routing is connected to a computer with a network cable.

2.Enter the route from the connected computer (enter in the IE address bar, the user name and password are admin, the manual has), the page prompts the pop-up "Setup Wizard", click Next, select PPPoE mode, next, fill in the account password you dialed, select auto-dialing, save, and it's OK;

If the "Setup Wizard" does not pop up when entering the route, directly click the network parameters on the left - > WAN port setting - > select PPPoe mode - > fill in the account and password you dialed - > select auto-dialing - > save, and you're OK;

Different routers are all similar, all choose WAN->PPPoe-> enter ADSL account password >auto-dial->save).

First, the antenna of the wireless router on the market is basically a 5dbi omnidirectional antenna, simply put, the same type of single antenna and three antennas are a little different, mainly for the reliability of network transmission, the range of signal gain.

Second, according to your requirements, only for your own mobile phone, 54m is enough.

Personal advice: If you buy an ordinary router, it is best to buy a 300M one, if you think ** is too high, then buy a 150M one.

Reasons: First, the speed will be much faster when it is applied in the LAN in the future; Second, ** is not much more expensive.

If the signal is not very good, you can buy a 9dbi omnidirectional antenna, which should be able to meet your practical application.

If you can pass through the wall, it's best to buy three antennas! Let's go to the ** network to have a look. Or you put your room in a mini router installed! Prerequisite, your room must have an internet cable! **There are on the net, if you are interested, go and see it.

Enough, you can buy a tp link dual-antenna wireless router, or you can put the router in the center of the house, no matter what room the phone is in, the signal strength should be about the same, and then throw the network cable long point for the computer, and that's it.

Haha, 80 meters of my house is not enough, the mobile phone receives this kind of signal, it is not better than a notebook, it is recommended to buy a netbook, hehe, less than 2000, forget to adopt.

The theory of home use is 100 meters, and the distance between more steel bars is greatly reduced.

If it's 2 wireless routers.

Your wiring is wrong.

There are 2 ways for you to try it.

Method 1: 1. Telecom broadband is connected to the WAN port of TP-Link.

2. Set up dial-up Internet access.

3. DHCP is enabled on the LAN port of TP-LINK

4. Set the wireless SSID as: WIFI-L

5. WPA encryption, set the password.

Note: The access address of Ti-Link is that the access address of Gateway 1 and D-Lingk WAN port is empty, which can be set to dynamic IP 2 and D-Link to set the access IP to.

3. The LAN port of D-Link is closed for DHCP

4. The LAN port of D-Link is connected to the LAN port of TP-LINK.

5. Set the wireless SSID to WIFI-D

WPA encryption, set the password.

This is known as the dual wireless hotspot LAN connection method.

Method 2: The tp-link settings are the same as those of the d-link above

1. The WAN port of D-Link is connected to the LAN port of TP-LINK, and the WAN port of D-Link is set with dynamic IP

3. The IP address of the LAN port of D-Link is set to :

4. DHCP is enabled on the LAN port of D-Link

5. The LAN port of D-Link is connected to the LAN port of TP-LINK.

6. Set the wireless SSID to WIFI-D

WPA encryption, set the password.

These are LAN hotspots with 2 different network segments.

The advantage is that the pressure on the main route, TP-Linkde DHCP, is reduced, so that the number of hosts that may access the Internet can be close to the theoretical value.

You can set the IP manually in the settings

Generally, if the number of Internet access cannot be reached, it is actually DHCP overrun, and you can set a manual IP.

First of all, your TP-Link should be connected to telecom broadband with a WLAN port.

Have you analyzed why a single router can connect 32 (27) terminals and 10 (5) cannot access the Internet? Because the ability of home routers** is limited, there are too many connected devices, which will greatly increase the burden on the router, resulting in data connection interruption or transmission errors. Even if you use two routers, you can't make 59-15=44 valid Internet access.

It is recommended that you set up a few of these tablets as WiFi hotspots to see if they can meet your requirements.

The wiring method is basically correct, the two SSIDs are the same, the channels are the same, the wireless password is the same, don't use the line to connect to the second route, both routes are open WDS, fill in each other's wireless MAC addresses OK.

Looking at the picture, it seems to be a dislocation of wan and lan!! Turn off the DHCP of the two routers, the LAN addresses must be different, each control its own PC, and configure the IP of each PC. This controls the number of loads on both routers.

I'll give you a way to try it, buy a router, don't use wireless, and give you those two wireless routers in two ports. Since there are so many things to connect, you must choose the maximum transmission power on the wireless router settings.

The key question is: Does the WAN port status on your router show that the connection is successful?

If the phone can connect to the wireless network and show that the connection is successful, it just means that the wireless function of your router is normal; Whether you can connect to the Internet or not depends on many aspects.

1) How is the hotel's internet set up and used? Is it possible to set up your computer to "automatically obtain an IP address" to access the Internet?

In this case, it also depends on the IP address of the network segment that you obtain. If it is the address of the network segment, then it happens to be the same as the address segment of the default LAN port of your router, and there will be a conflict, which will definitely not be available.

2) Does the WAN port on the router show that the connection is successful?

If not, then it certainly won't be able to get on.

You need to make the problem clear, otherwise it won't help you.

The router is not connected to the Internet, for example, your router WAN connection is not set up correctly.

The bandwidth is too small, it will definitely get stuck, at least 4m is needed

Old telecom users should be able to upgrade 4m for free.

You consult the next 10,000 to see.

It can be used, but 2m will be more stuck when watching TV.