The purchase guide of oil mist separator, the difference between oil mist separator and oil mist sep

Why choose a mist extractor?

The fog suction can suck up and purify about 99% of the harmful substances in the machining environment, which plays a role in protecting the health of workers and prolonging the service life of the equipment. Although there are no strict regulations on processing equipment operating in a confined environment in China, it is required that fog extractors must be used. However, in developed countries such as Europe and the United States, the installation of suction fogs has been listed as an industry regulation.

Therefore, the installation of fog extractors has become a historical trend.

How to choose the right mist extractor for your machine tool?

When shopping for an aerosol extractor, there are four questions that we recommend you should consider carefully. First of all, the efficiency of the aspirator: that is, the percentage of the harmful substances that are sucked and the total volume (volume) that passes through the aspirator.

Secondly, the suction volume of the mist: for example, the efficiency of a suction device is very high, but its suction volume is only 10 cubic meters per minute, which is still unable to meet the actual requirements of most enterprises. Again, the number of vacuums:

The total volume of the workshop to be suction needs to be measured in advance, so that it is easier to decide on the number of mist suction devices to buy. For example, the total volume of the workshop is 10,000 cubes, and the suction volume of the suction mist is 500 cubic minutes, then the enterprise needs to buy 20-22 products to meet the requirements, and less than 20 suction mist will not be complete. Finally, the service life of the mist, the maintenance cycle of the renewal, and the cost.

Are there any optional parameters when purchasing an inspirer?

It is recommended that you choose a mist suction according to the required air volume, your machine processing volume, your desired treatment environment (dust, oil mist, water mist), treatment concentration and installation location.

What are the methods for harmful oil mist powder in the workshop?

At present, the more effective products on the market to treat the air quality of the workshop are mainly divided into three categories: first, to reduce or control the generation of pollution sources; Second, install high-power emission equipment to discharge gas, oil mist and dust to the outdoors; The third is to use oil mist separators and other treatment equipment to filter and purify indoor air. Although the three types of methods have their own merits, at present, the oil mist separator has become the first choice for enterprises to improve the indoor environment of the workshop by virtue of its advantages of low investment, high efficiency and quick effect.

When purchasing industrial oil mist separators, we should pay attention to: 1According to the actual working conditions of the machine tool, different power oil mist separators are selected; 2.Distinguish between pure oil processing and cutting fluid processing, and choose an oil mist separator with a high-efficiency after-filter for pure oil processing.

Oil mist separator.

First, the use is different.

Lubricating device: The lubricating lubricator is a special lubricating device, which atomizes the lubricating oil and injects it into the air flow, and flows into the parts that need to be lubricated with the compressed air to achieve the purpose of lubrication.

Oil mist separator: The oil mist separator is used to suck out the oil mist in the processing chamber to purify the air, so as to protect the health of workers.

Second, the installation location is different.

Lubricators: They are usually installed at the gas inlet and outlet of cylinders, etc.

Oil mist separator: usually installed in CNC machining centers, cleaning machines, die-casting machines, CNC lathes and other machining equipment.

Third, the principle is different.

Lubricator Lubricator: The lubricating oil is powered by compressed air, which sprays the lubricating oil into a mist and mixes it with the compressed air, and as the compressed air enters the parts that need to be lubricated.

Oil mist separator: The rotary screw filter of the oil mist separator will intercept the solid particles in the inhaled medium first, and then intercept the liquid phase mist by high-pressure collision away from the heart of Xian, and finally collect the oil mist containing fine dust and discharge it directly into the air through the post-activated carbon filter.

The mist separator compressed air flows from the inlet to the inside of the filter and then to the outside. The oil particles that enter the fiber layer are intercepted by their motion inertia and collide with each other or collide with the multilayer fibers and are adsorbed by the fibers. The smaller particles are adsorbed by the fibers, and the further outward, the particles gradually increase and become liquid, condense on the surface of the special foam layer, and flow to the bottom of the cup under the action of gravity and are discharged.

Types of Mist Separators:

1. Gravity separation type: horizontal and vertical gravity separators are commonly used;

2. Collision coalescence type: wire mesh coalescence, corrugated plate coalescence separator;

3. Cyclone early width separation type: reverse flow, axial flow cyclone separator, compact gas-liquid separator;

4. Rotational expansion type.

treatment of industrial oil mist and hidden particles; It is suitable for CNC machining center; Lathe; grinding machines and other machines are used to change the hall; The gold engine oil mist separator adopts negative pressure separation technology; Fully mechanical structure design, <>

Oil mist separator.

The main difference between the two is when they are used and what they do.

The lubricator is mainly used when the cylinder temperature is low and the gas movement speed is too slow; The instrument can make the liquid oil into a mist and send it to the cylinder to play a role in lubrication;

The oil mist separator is mainly used when the gas in the cylinder contains more oil vapor and water vapor, and the purity of the cylinder gas is low; The instrument removes oil and water from the compressed air and plays the role of separation and purification.

Generally, in the gas circuit, there will be three parts, there is an oil mist separator and an oil mist device, the oil mist separator is to separate the moisture and oil mist of the gas produced by the air compressor by centrifugal action, and the oil mist is to lubricate the treated gas with oil mist, and the oil must have VG32 turbine oil.

Both are the same, one is the abbreviation, the other is the full name, you see if you are talking about this oil mist separator.

Oil mist separator, Shenzhen Huawei Xing's industrial CNC oil mist purifier does a good job.

The same product, but with a different name.

The selection mainly considers the air volume and the type of oil mist to be processed.

The principle of oil mist treatment mainly includes mechanical, electrostatic and centrifugal type.

Both oil mist separators and oil-water separators separate the oil from the gas, but the oil mist separator can separate finer oil droplets.

The oil mist separator is an environmentally friendly product used for machining purification of oil mist, which is made of a combination of high-efficiency essence filter media and high-quality click.

To put it bluntly, the oil mist separator is to pump the oil and gas out through the wind wheel. Purification and separation are then reached. A physical filtration method is used to return the filtered oil mist to the oil cylinder.

The oil mist and water mist generated by the machinery at the same time of production can be re-developed, and the machine has the characteristics of high-efficiency and energy-saving lamps. At the same time as the rapid development of machining. It can be achieved very well.

For the effect of purification and environmental protection, the filter material component of the oil mist separator is composed of more than three kinds of filter media, including primary, intermediate and advanced lamp oil mist filter media processes. Different grades of filter media.

The size of the filter media is different for filtering, the higher the better.

Features of the oil mist separator:

1.The filtration effect is efficient and long-lasting, and the imported filter media: compared to the e-book and its purification efficiency will not change much.

2.The performance of the equipment is long-lasting and stable, and the high-protection motor and motor protector are used to make the machine stable and long-lasting.

3.Easy to maintain, the maintenance of the machine is very simple, and it takes less than 30 seconds to replace the cleaning filter media.

4.Maintenance cost, one year maintenance cost is low, and the machine effect is good. Relative to classical and electronic. The upfront investment is large.

5.Simple and reliable installation. It only takes an hour to install, so you can say goodbye to the hassle of disassembling and disassembling procedures.

6.Maintenance is simple and fast, and there are no static high voltage and wearing parts in the machine. The high protection of the wind turbine makes the machine very safe.

7.The oil mist state and dust applicability of machine purification are widely distributed, which is the first choice for many factories.

Log in to the official website of Shenzhen Huawei for details to learn about the oil mist separator.

How the oil mist separator works:

The centrifugal rotation negative pressure of the suction port makes the oil mist be sucked into the air duct in a directional manner, and the oil mist particles collide under the action of the wind wheel, and the tiny particles are collected into larger particles that are easy to be controlled, and the separation from the air is realized under the barrier of multi-stage high-efficiency filter materials, and the filtered oil is discharged through the oil discharge port.

The function of the oil mist collector is to solve the pollution problems such as oil mist, water mist or dust during machining. For electrostatic oil mist purifiers, it is not suitable for use in processing places that generate water mist, because it is not cost-effective; It's okay to solve the problem of oil mist, and the most suitable place to apply is dust. As for the installation position, it can be mounted on the top of the machine or next to the machine, which is linked to your needs.

Function: It can be used in m, aerosol particles and rust dust and carbon particles larger than m that are difficult to separate from the main pipeline filter and air filter. It is most suitable for installing on the air source of solenoid pilot valve and gap seal spool valve.

Working principle: The structure of AM series oil mist separator is similar to that of AFF series main line filter, only the filter element material is different. This filter element is mainly made of microfiber and glass fiber materials, and the ends are sealed by rubber.

Due to the large filtration area of the filter element and the metal skeleton of the filter element, its service life is long, and the pre-filter is not applicable.

The compressed air of the AFM series mist separator flows from the inlet to the inside of the filter element and then to the outside. The oil particles that enter the fiber layer are intercepted and collide with each other by their motion inertia or the particles collide with multiple layers of fibers and are adsorbed by the fibers. The smaller particles are adsorbed by the fibers, and the further outward, the particles gradually increase and become liquid, condense on the surface of the special foam layer, and fall to the bottom of the cup under the action of gravity and are discharged.

If you want to know more about the oil mist separator, you can take a look at Wuxi-Smart, which is not bad.

In the machining industry (such as CNC machining, lathe machining, grinding machine processing and other processing industries), due to the use of coolant for the cooling of workpieces such as cutter heads and grinding heads, the coolant is atomized during the cooling process, resulting in oil mist. At this time, the oil mist collector can help the machine processing industry to clean the air in the workshop, reduce maintenance costs, and protect the health of workers.

The oil mist separator has centrifugal type and electrostatic type, suitable for different working conditions, each has its own advantages and disadvantages, and the working principle is not the same. In terms of domestic manufacturers, Bodi's machines are very good, basically comparable to some well-known brands outside the United States.

You're talking about the oil-water separator, which has a filtration function, but it is generally a coarse filtration.

The oil mist separator, also known as the vacuum pump filter, is to filter the oil smoke, on the one hand, the filtered oil droplets can be collected and used repeatedly, on the other hand, the filtered smoke is not polluted. Many people don't know whether they can be discharged directly after filtration, and an easy way to do this is to have a report. Filter brother oil mist separator, providing environmental protection test report, is trustworthy.