After reinstalling the system, others can access the Internet with the router, but I can t get on 5

From your description, you can tell that the wireless routing virtual interface of the router is normal, but the wired virtual interface does not have DHCP enabled. As a result, your computer doesn't get the IP.

You need to manually set the computer IP and the IP of the router's wired interface in the same network segment, the method can be found in the router manual. Users who can access the Internet wirelessly can also enter the router to turn on the DHCP service function of the wired interface.

The IP is not assigned.

See how your router is set up.

Turn off the firewall.

Set your computer to get IPs automatically

That's it.

If you can't get it automatically, you can manually set the IP and DNS by yourself

Does IP Automatically Obtain IP? It should be changed to automatically acquire IPs

Summary. broadband issues;

Router setup issues (router connection issues.) The Internet access mode is set incorrectly);

Operator restrictions: Broadband operators in some parts of the country have some improper practices, that is, restricting users from using wireless routers;

Router issues: If your router doesn't display your name or keeps getting an error when you enter your password to connect to the network, restart your router.

The computer has changed to a router but can't connect to the Internet, what should I do?

1.broadband issues; 2.Router setup issues (router connection issues.)

The Internet access mode is set incorrectly); 3.Operator restrictions: Broadband operators in some parts of the country have some improper practices, that is, restricting users from using wireless routers; 4.

Router issues: If your router doesn't display your name or keeps getting an error when you enter your password to connect to the network, restart your router.

What should I do if I change to a new router and plug in the network cable and it doesn't work.

1.First of all, determine if your router is set up correctly. Open the router settings page and tap on the top right'Advanced settings'Link 2

On the Advanced Settings page, click on the left navigation'WAN port settings'On this page, check again whether these three items are set correctly, the broadband account number and password are provided to you by the broadband provider, and you must enter them correctly. 3.Once we've made sure it's okay, let's click on it below'Connections'button, if the settings are OK, it can be successfully connected, and it will be displayed at the top'Connected'.

If you see 'Disconnected' above, or there are some error messages, there is a problem with the settings, if the broadband and password are fine, change the 'WAN port connection type' and try again. 05If there is no problem with the settings, we can see if the 'Parental Control' function is enabled, or similar to the Internet whitelist. If the parental control function is turned on, and your device is not added to the parental device list, the Internet access will be restricted, if the restriction is set to prohibit the Internet 24 hours a day, it is equivalent to not using the router's network function at all.

Summary. Turn on the computer, find a random browser, such as Google Chrome, and enter the router settings page at the top of the browser: 192 points 168 points 1 point 1 point.

Enter the username and password, generally the default is admin and admin, or it may be guest and guest, if it is not correct, you can check the instructions on the back of the router. Then click System Tools, and then left-click to restart the router. A new page will appear, click Restart Router from the page that appears.

Turn on the computer, find a random browser, such as Google Chrome, and enter the router settings page at the top of the browser: 192 points 168 points 1 point 1 point. Enter the username and password, generally the default is admin and admin, or it may be guest and guest, if it is not correct, you can check the instructions on the back of the router.

Then click System Tools, and then left-click to restart the router. A new page will appear, click Restart Router from the page that appears.

The new router needs to be reset Some users think that they only need to connect the new router to the network to work normally, so they do not make any settings for the new router, resulting in the inability to access the Internet through the new router.

After replacing the router, the computer cannot connect to the Internet, it may be that the network cable port of the computer is not connected, find the WAN socket on the back of the WAN router, and connect it with the home cable. Connect the LAN socket to the computer network cable socket.

When the newly purchased router is connected to the network, it must be connected according to the following principles: any one of the WAN ports is connected to the computer. When you connect to the router, you must follow the principle of appeal.

1. Online Internet access: Users need to prepare 2 network cables, one network cable is used to connect the WAN interface between ADSL modem (broadband modem) and router; Another network cable is used to connect the computer to the LAN port of the router.

2. Optical fiber Internet access: Users need to prepare two network cables, one network cable is used to connect the WAN interface between the optical modem and the router, and the other network cable is used to connect the LAN interface between the computer and the router (any one of 1 2 3 4 can be used). The connection method is the same as that of the **line, please refer to the ** above for connection.

After reinstalling the system, the settings will be deleted, and the router settings must be set up again! It is recommended that you reset both computers once!

It's you who set it up incorrectly... Use the 360 disconnected first aid kit to complete the repair with one click...

The computer is set to automatically obtain IP and DNS, check whether the local connection is disabled, whether there is an extra local connection, and just leave one.

I don't have a network card driver installed. Install the NIC driver.

Right-click on "Online Neighbors" - Properties" and "Right-click on "Local Connection" - fix "You go try!"

Analyze it next:

1.Ensure that there is no quality problem with the 67-meter network cable (you can use a line tester to measure it).

2.You say that after your route is set, your other computer can't access the Internet, so can your own computer access the Internet? [Can go to the Internet (note: connect to the port and go directly to the Internet, there is no dial-up) means that the routing is no problem, and you can't access the Internet, which means that the routing is not set up].

3.If I can access the Internet (directly connected), can I use the computer where you can access the Internet to try the other ports of the route?

4. If these are all good, then look at your computer that can't access the Internet, and see if its IP address is automatically obtained. (If not, change to auto-get).

If you can't do all of the above. (Make sure that there is no problem with the network card first, and then reinstall the system on the computer that cannot access the Internet).

Try changing the MAC address of another machine that can't access the Internet to the one you can.

Open the properties of the local connection, find the configuration options, Advanced, click "Network Address", enter your original MAC address, and select it.

Enter your device that can access the Internet, right-click on the network icon in the lower right corner of the desktop - status - support - details. You can see it inside.

The network cable of 67 meters should be through, but it is just a packet loss.

First of all, you need to make sure that telecom allows multiple computers, and some local telecom restrictions are made.

Sending only data means that you are connected with the router, and not receiving it means that you are not connected to the Internet.

First, confirm that your IP address is set up, and then set your router to automatically get the IP.

1: There is no problem with the general network cable, see if your crystal head is not good and the contact is not good.

2: There is a problem with the driver settings of his computer's network card.

3: Whether the socket of his computer network card is missing or has poor contact, check the interface of the router also.

4: Excluding the restriction that the router cannot be used in the region, even if the router is used in some areas of our hometown in Shandong, it cannot be used on two at the same time.

5: Is it a speed limit, open P2P software?

6: His computer is poisoned

None of these six points are known only to God

Follow the setup wizard exactly.

Whether the DHCP service is turned on.

The landlord forgot the most critical step, and called ** to call Telecom to refresh your account.

There is no setting according to the manual.。。。 The estimation ** is set incorrectly.

1. When you enter the router for the first time, a setup wizard will appear, and you can follow the steps according to the prompts.

2. If there is no setup wizard, you can follow the steps below:

2.In the WAN port settings, enter your broadband account and password. Save.

3.Click on the wireless settings: turn on the DHCP function, and the password, you can choose to set it or not.

After the above operations are completed, check whether your ADSL (hereinafter referred to as the modem) is connected to the WAN port of the router. It's usually the blue one. Make sure that all of the above operations are done, restart the router and the modem.

At this time, the router will automatically dial out the Internet to access the Internet. After about 3 minutes, turn on the IE on the computer and see if you can access the Internet. If it can be on, it means that both the router and the cat are correct. If you can't get it, there must still be some steps that are not set up correctly.

Talking about wireless internet. If you can access the Internet with a network cable, turn on your wireless connection, see if the IP address of the wireless connection is automatically obtained, if so, see if the gateway is If all this is correct, congratulations, you can access the Internet wirelessly. If you still can't get it, you can manually set your IP address.

That's it.

Answer: Hello, I have seen your question, and I am sorting out the answer, please wait for a while Hello Do you remember the password of the router Or has someone changed the password You try to forget the password After retrieving the password, you can connect to the network again.

Ask a question and know that it can't be used.

Ask how to reset your router.

Answer: Try the following methods: First, plug in the router and power it on. Locate the reset port or button on your router; Insert the pen (you can also use a card pin) into the reset hole, there is a small button inside, press and hold it and don't move; About 5 seconds, wait for all the lights on the network port to turn on, and then release it.

If your router's reset is a button, it's even more convenient to press and hold for 5 seconds and release it.

Next, you can reset the router with the default address wifi.

There is no Internet access mode set on the router, and you can access the Internet by logging in to the management interface and setting it.