Wireless Routing The wireless indicator always flashes when there is no connection, and the computer

First of all, friend, can you elaborate on your situation?

1. Is it the first time to use a wireless router? Or did it work normally before, but now it's in this situation?

2. What are the tips of the computer?

1. If it is the first time to use, please follow the instructions of the router, connect the network cable to the cat, connect the cat to the router WAN port, connect the router LAN port to the computer, enter the computer for relevant settings (the specific settings can be seen in the manual, or search for related problems, it is inconvenient to describe in detail), after setting, see if you can access the Internet normally. Check the connection in detail and see if there is any looseness at the joint. If the connection is correct, there should be lights on at each connector.

Second, if it has been used normally before, and now this situation occurs, please first eliminate the problem of the router, try to restore the factory settings (usually there is a button on the router, press and hold for a few seconds), if the factory reset still does not work, and then rule out whether there is a hardware problem, take the router to a friend's house or neighbor's house to see if it can be used normally. If it also cannot be used normally, it means that the router is broken, and it is recommended to repair it or buy a new one.

I wish you a speedy solution, thank you.

There is no direct relationship between the wireless indicator light and the network is not connected, whether the network is normal depends on whether the WAN port light is on, and whether the router is set correctly, I really don't know how to read the routing manual, it really doesn't work, play the warranty of the network operator**, let them take a look.

Unplug the router and plug it back in after 10 seconds, it is possible that the router routing table is full!

The lights on the wireless network on the router are always flashing What's going on?

The lights on the wireless network on the router are always flashing What's going on? 1. When the router system indicator flashes, it means that there is an abnormality in the router and can be solved by resetting the router. 2. Press and hold the reset button on the back of the router to reset the router.

3. Open the browser and enter ** in the address bar. 4. Enter the router setup interface and follow the steps of the setup wizard to set up the router. 5. After the setup is completed, wait for a few minutes, turn the router back on, and you can connect to the Internet normally.

Wireless router connection diagram When the wireless router WAN port lights up and flashes, this situation generally means that the router is normal, if you can't access the Internet, you just need to restart the router, that is, unplug and plug it back in.

Hello dear, routers are all green lights, but there may be the following reasons for not connecting to the Internet: 1. The network cable and the router are in poor contact, and the network cable is replugged and unplugged. 2. If there is a problem with the router setting, try to reset the router again. 3. The router will be introduced later.

Check it like this: 1. Call the operator's customer service** to see if there is any problem with the external network. 2. Reseat the network cable once The network cable from the cat is connected to the WAN port of the wireless router, and the computer is connected to any LAN port of the wireless router. Three、..

Hello dear, it may be due to the problem of broken optical fiber, the problem of service provider settings; The registration light of the mobile modem has been flashing, indicating that it is not registered, and it is enough to wait for registration; The mobile light modem registration light is always on, indicating that it is OK to set up a router to connect to the Internet; More on that later.

The green light of the wireless router keeps flashing: normal. Wireless routers have three types of lights:

sys, lan, as long as the power is turned on, the sys light will be on. 2. After the router and the cat are connected, the WAN light will be on. 3. The LAN light corresponds to the non-return interface, and the light will be on which port the network cable is plugged into.

2.Reopen the modem (optical fiber modem), router, and switch to see if the light signal is normal after reopening, usually a green light or orange light, and a red light indicates that there is a problem3Is the computer plugged in**?

For example, if it is plugged into the router, please turn off the router and plug it directly into the middle and it will be introduced later.

Reading guide:The router indicator sail bends and displays green normally (or white blue),All devices connected below cannot access the InternetThis phenomenon may be due to problems with the operator's network、DNS or mtu settings are not suitable。 You can press Finished.

Restart your router. Method A (the operation mode of this instance), notify the network service provider, Telecom 10000, and inform the staff that the optical modem cannot access the Internet when connected to the router, and take the trouble to change the optical modem from routing to bridging. Wait 10-30 minutes and restart the modem and router.

More on that later.

The green light of the router keeps flashing and you can't access the Internet1, the network cable and the router are not in good contact, and you can try to plug and unplug the network cable again. 2. If there is a problem with the router setting, try to reset the router again. 3. If there is a problem with the router, restart the router or restore the small hairy cat.

You can log in to the management page of the router to see if the wireless network is turned on, and whether the wireless network name and password have been set.

If there is no problem with the settings, but the router wireless indicator does not light up, you can consider pressing and holding the router reset button for 10-15 seconds to restore the router to factory settings, and then reconfigure the router parameters.

If it still doesn't work, it is possible that the router is broken, and it is recommended to find a professional to repair or replace it.

It should be noted that the above is only for independent routers, it is recommended to restore factory settings, if it is an optical modem router all-in-one machine (smart gateway), do not restore factory settings at will, if it is a smart gateway problem, it is recommended to contact the operator directly to deal with it.

Summary. As far as the description is concerned, it is obvious that the router cannot be connected to the Internet. The network equipment on the next level of the router is not working properly. For example, it is recommended to check whether the light signal light of the modem is green.

In addition, wifi is an invisible network cable, connecting to wifi is connecting to a router, and that's it.

Why does the router light flash to connect to wireless but not to the Internet?

As far as the description is concerned, it is obvious that the router cannot be connected to the Internet. The network equipment on the next level of the router is not working properly. For example, it is recommended to check whether the light signal light of the modem is green.

In addition, the fire only touches, wifi is an invisible network cable, connected to wifi is connected to the router in the mountains, that's all.

I couldn't connect to the wifi when I used it normally.

Didn't prompt, only now see it. I'm sorry.

In this case, the router will be powered off for 15 minutes and then powered on.

Summary. Hello, plug in the network cable, the computer shows that it is not connected, the router indicator flashes 1, turn on the computer. 2. Open the browser, enter the general router address in the address bar is this or check the login information on the back of the router) Enter the route - enter the user name and password, (the default is generally admin).

Set Router Dialing]: 1. In the [Setup Wizard], select [PPPoe Dialing] (some are ADSL Dialing), enter the username and password for Internet access according to the prompts, and save. 2. In [Network Parameters] --WAN Settings], select [Normal Mode], and select [PPPoe Dialing] in the three options of [Connection].

The next step is to select [Auto Connect], Save, and Exit. Dear, the above is my summary of your problem, do you see if there is anything else you need me to help you with.

Plug in the network cable, the computer shows that it is not connected, and the router indicator flashes.

Hello macro song, plug in the network cable, the computer shows that it is not connected, the router indicator flashes 1, turn on the computer. 2. Open the vertical browser, enter the general router address in the address bar or check the login information on the back of the router) Enter the route - enter the user name and password, (the default is generally admin). Set Router Dialing:

1. In the [Setup Wizard], select [PPPoe Dialing] (some are ADSL Dialing), enter the Internet user name and password according to the prompts, and save. 2. In [Network Parameters] --WAN Settings], select [Normal Mode], and select [PPPoe Dialing] in the three options of [Connection]. The following is to select [Auto Connect], save, and exit.

Dear, the above is my summary of your problem, do you see if there is anything else you need me to help you with.

Can't find what you said.

That's it.

But I can't do this with you.

Reason 1: "The connection between the optical fiber pigtail and the optical fiber coupler is disconnected, that is, there is a problem with the optical fiber connection between the optical modem and the optical fiber, although the staff is still checking the connection when installing Dannian, but after a long time of use or human factors will cause the coupler and the pigtail to be disconnected." Workaround:

Try to reconnect the pigtail, don't use too much force, it is easy to cause the fiber to bend and break. Reason 2: Since the materials that make up the optical fiber are glass and plastic, it is very easy to damage and break the optical fiber when it is bent and extruded.

Solution: The general optical fiber damage and fracture is not able to see the obvious scar, and the user himself can not repair it, it is recommended to immediately call ** to find broadband maintenance personnel, optical fiber fracture repair is very convenient, and very cheap. Reason three:

If the optical modem fails, the probability of such failures is still very small. Solution: Find a staff member to change to a light modem.

Reason 4: The remaining reason is probably the failure of the uplink splitter, which will cause problems in the local area network, and many users in an area will not be able to connect to the network. Workaround:

After the power is off, wait for a few minutes, and then restart the modem. This kind of failure will be repaired soon after the nuclear delay.