How to use D LINK brand land travel equipment

After the connection is established, the login window pops up, enter the administrator username: admin, password: (empty, remember to set it after setting), click the "OK" button, enter the management interface, and the basic settings are in the "home page", including WAN (WAN settings), LAN (LAN settings), DHCP service settings.

The login username and password are admin by default, if you don't log in often, don't change it, it's easy to forget.

Then go to the setup guide and follow the guidance to set it up.

If you use this wireless, then enter the wireless settings, set the wireless password, and so on

Use or try one by one, the username is generally admin, and so is the password.

Web format settings!

Routers are almost always fool-proof, so they don't need to be set up much.

Look at your instruction manual, which has the management address and account number and password, which is basically or.

If you don't know how to set it up yourself, ask a friend to help you set it up

D-link is also an international product pie, but my personal opinion!!

It's still tp-link's good!!

D-link: I've been fooled.

You see if it's still out of warranty.,Just take it for repair.。。

See if it's still out of warranty.,Take it for repair.。。

The school generally either does not need to dial in Sun Juyuan, or log in to the web page to enter the account to access the Internet, in short, the network environment is very different from the family, so the answer to the surplus causes your routing to be not adaptable. For example, the address assigned to you by your school is unlikely to be 192 network segment, and the school is mostly 10 network segment.

Obviously, if you don't know how to clear the network configuration, it is recommended that you go directly to the school network center to ask.

Locally Connected -Properties·· The Internet protocol is set to automatically get the IP ah!

The main thing is that the IP segment of your local connection is not yet in the IP of the router or !!

Teach you a method: run cmd and then enter ipconfig in cmd to see if the ipv4 address, default gateway, and subnet mask set by the IP connection are normal!!

First, you need to set your computer to the IP of the two IP segments you just mentioned, and whether your router has been changed and whether the gateway has been changed? If it does, try it after factory resetting it.

You have to set your own IP to or from 2 to 254).

Then you can enter the settings interface.

It's normal, but the password hasn't been changed. As long as you connect to it, you can access the Internet, and other computers can connect to the port of the router to access the Internet.

It can be normal.

You don't have to dial in after you set up Auto-connect.

I bought TPLINK's TL-WR541G+ at home, I think it's pretty good, our house has a total of 4 floors, three floors apart (cast-in-place kind of reinforced concrete), it can be used on the first floor, of course, the speed is slow, the signal is weak. It's good to use each place on the same floor.

If the product performance is the same, of course it is D-link.

Since QQ can be used, it means that the network is connected, and the inability to access the Internet means that DNS resolution cannot be carried out, which is a typical DNS problem. You can set a static DNS address in the IP properties of the wireless card. You can ask the operator what their DNS address is, if not, then go to the Internet to check the national DNS list file, and choose one that is on the same network as yours and relatively close.

You can manually specify the DNS address on your computer, and you can fill in the DNS of your local operator and try again.

The general network management is that you can modify it yourself.

If it is according to the manual, there should be no problem with the visible settings. I tried it at the maintenance point, which means that there is no problem with the road tour. The most likely problem is telecommunications, some places have strict requirements for broadband use, the first line can only correspond to one machine, but routing Internet access as long as one machine to use it should be no problem.

Call 10000 and ask how to come back, don't be afraid, just say that you want to go online directly as soon as you turn on the phone, and you don't need to dial up the computer, so you can buy it.

The router is not set up. Go inside the router and see if it's connected.

I'd love to help you, but the tp-link I use is bright and ready to be presumptuous and don't know how to pretend to understand.

I just found a state to destroy the circle and found a setting method with a detailed explanation of the map.

The full three lights of the wireless router do not mean that the network is smooth, because there will be some very inexplicable problems in the wireless data and wireless reception of the router, and it is recommended to restart or reset the router.

You check whether the wireless settings of the router are turned on (log in to the router IP) and whether your router has a password. If you haven't logged into your router, then the wireless is off.