After the cat is reset, how to use it again??

After the cat reset, you need to log in again to access the Internet and set the password before you can use the Internet normally.

Tools Raw materials.

China Unicom Fiber Optic Cat.

Computer. Setup steps.

1. Enter the computer browser to enter the routing login interface; You are prompted to enter a username and password, the default username is user, and the password is marked on the back of the router. After entering, press enter to enter the router configuration interface.

2. After logging in, the page will appear with the options of each setting, as shown in the figure below.

3. Click Network, then click Broadband Configuration, and then click Broadband Internet Settings; Enter the Internet access and password provided by China Unicom Broadband here, as shown in the figure below.

4. Then set up the wireless wifi, click on the network, click on the basic settings, you can modify the SSID name, that is, the wifi name you searched for later, click OK, as shown in the figure below.

5. In the network settings, click WLAN configuration, click Security Settings, click WPA pre-shared key, set the password for wireless Internet access, and confirm the setting completion point, as shown in the following figure.

6. After the above steps are completed, you can access the Internet through the network cable and wireless connection, of course, you can also modify the management password of Unicom's optical fiber modem, click on management, click on user management, as shown in the following figure.

Generally, China Unicom's optical fiber modem can be directly connected to the Internet after the technical personnel of China Unicom come to install it, and under special circumstances, you need to set up the optical fiber modem by yourself.

Are you sure it's a cat? You should be talking about the cat with the router.,After the reset, you need to reconfigure the parameters.,Generally fill in the password and password.,Good for dialing.。 If you have a wireless function, it is very simple to set the wireless parameters.

But if you don't understand it, it's difficult.

The cat reset you are talking about here should be a light cat, right?

It is generally not recommended to reset the optical modem.

If you reset it, you need to log in to the management page to make the corresponding settings, you need to know your account opening and password, write the corresponding location, and the password can be asked by the operator.

If it's a simple dial-stern, the reset doesn't affect. The password is set at the router dial.

It is recommended to add a router and reset the router if necessary. For example, the optical modem reset of the telecom is nothing more than to fill in the password, and there is no other meaning, because there is nothing to set up.

Cat reset is nothing, right? You mean wireless routing?

Hello, you're not talking about cats, it should be a wireless router.

1. There is a reset hole in the back of each cat and it can be restarted after holding it down with a needle for 3-5 seconds.

2. Don't let the cat connect to the route, and connect directly to the computer of this Qiaoshu. Access via the web can be accessed by typing in the address bar of the browser.

Restart is to power off, turn off the switch, plug in, turn on the switch, is to clear the data packet, in fact, it is also the heat dissipation process, the first few minutes of the re-call to wait for it to connect to the Internet, and then it is still normal to surf the Internet, and the Internet is smoother.

Reset the wireless modem.

It needs to be operated in the background of the wireless modem.

The steps to reset the wireless cat background are as follows: with ant holes.

1. In the browser address bar, enter the wireless modem background management address or.

2. Enter the wireless cat administrator password beam.

3. Click on the Advanced Settings option.

4. Select Device Management.

5. Click Restore factory settings in Device Management.

6. Click Restore factory settings to complete the reset.

Reset the wireless modem.

It needs to be operated in the background of the wireless modem.

The steps to reset the wireless modem background are as follows:

1. In the browser address bar, enter the wireless modem background management address or.

2. Enter the wireless modem administrator password.

3. Click on the Advanced Settings option.

4. Select Device Management.

5. Tap Factory reset in Device Management.

6. Click Restore factory settings to complete the reset.

There are many models of cats, and here are two ways to reset a broadband cat.

1. The reset method with the reset key on the broadband modem.

1. Unplug the optical fiber and turn off the power.

2. Press and hold the reset button and then turn on the power, and then release the reset button after about 10 seconds when the red light changes from solid to flashing.

3. Wait for one minute before turning off the power and then turning it on.

2. There is no reset method for the reset button on the broadband modem.

1. Connect the broadband modem LAN port to the computer, open the browser and enter the computer to appear on the login page, enter the username and password on the back of the modem to log in.

2. After logging in, select Network Remote Management, delete the LOID, and click "Save App".

3. Then select Management, Device Management, Restore Factory Settings, Restore Default Settings, and the modem will automatically restart.

After the factory reset of the broadband modem is successful, the connected device cannot access the Internet after the factory reset of the broadband modem, and you need to reset the Internet access and password settings for the broadband modem.

Press the RESET button above for 10 seconds and you're OK.

Enter the management address of the cat in the computer browser (usually or; Log in with your initial username and password on the page that opens.

Method 1: Follow the setup wizard step by step; Generally, after the setting is completed, you need to restart the cat to take effect (the setting page Senhu face has a button to press the code or manually restart).

Method 2: If you don't need to route to the Internet, you don't need to set anything up at all. Sometimes there will be problems with the telecom's Chi Chun Lu ** line, you lift the **machine to see if it rings**, **ring line will have electricity, if you also install **, your cat should use a separator to connect to the **line, the signal is separated.

Connect the computer network cable to the cat;

Enter the management address of the cat in the computer browser (usually or;

Log in with the initial username and password on the page that opens, usually admin admin (usually written on the cat);

If you are familiar with cats, you can set it manually, and if you are not familiar, you can find the guide on the left;

Follow the Finger and Dan Setup Wizard step by step; Concealment.

Generally, after the settings are set, you need to restart the cat to take effect (the settings page has a disturbance button or manual restart).

You can press the restart button to restart the cat, if you don't press restart, the steps are as follows:

1. Restart through the LAN or router, and enter the address on the back of the router.

2. Enter the login interface according to the account number and password on the back of the router.

3. Find the navigation button of management and click OK.

4. Select the second option - Device Management.

5. Select "Device Restart", click the "Restart" button, and the router will restart.

Optical modem, also known as single-port optical transceiver, is a three-piece optical fiber transmission equipment developed for special user environments. The device adopts a large-scale integrated chip, simple circuit, low power consumption, high reliability, complete alarm status indication and perfect network management function.

An optical modem is a device similar to a baseband modem (digital modem), which is different from the baseband modem in that it is connected to an optical fiber dedicated line and is an optical signal.

The 1 and 4 ports of the optical modem are Internet ports, and a network cable is needed to connect with the computer.

Step 3: Enter the modem and select management.

After entering the optical modem, find management.

Step 4: Find Device Management in the management interface.

After entering the modem, select Manage, then Device Management, and then select Restart.

Step 5: Select Restart, OK.

Select Restart and then confirm to restart, and wait for a few minutes for the restart to complete.

Only the router can be restarted. Can't restart the cat There is no auto-restart feature in the cat.

You can only restart the cat by turning off the power, through the LAN or router, it is estimated that most cats do not have this function.

It depends on the situation, and there is no need to reset the account password if it has not changed.

If the account and password for surfing the Internet have changed, then you need to reset it.

1. Connect the line between the network cable, the router and the computer, and start the computer and the router equipment;

2. After starting the device, open the browser and enter it in the address bar to enter the wireless router settings interface. (If you can't get in, please look at the nameplate at the bottom of the router or the router instruction manual, the default settings of different models of routers are different.) ）

3. An account and password to log in to the router appear in the settings interface, enter the default account and password admin, or refer to the manual;

4. After successful login, select the interface of the setup wizard, which will automatically pop up by default;

5. After selecting the setup wizard, a window will pop up to explain that you can set the basic parameters of the router through the wizard, and click Next directly;

6. Set up step by step according to the setup wizard, select the Internet mode, usually ADSL users choose the first PPPoE, if you use other network service providers, select the following two according to the actual situation, if you don't know how to choose, directly select the first item to automatically select, convenient for novice operations, click next after selection;

7. Enter the account and password applied for from the network service provider, and go directly to the next step after the input is completed;

8. Set the wifi password, try to make the alphanumeric combination more complicated, and it is not easy to be rubbed off the network.

9. After entering correctly, it will prompt whether to restart the router, select Yes to confirm the restart of the router, and you can access the Internet normally after restarting the router.

There is a small hole in the cat, and it is restored by pressing it with a thin object for a few seconds.

The same goes for routers.

There was a small hole in the cat, so I pulled the thread out and plugged it back in.

With electricity, use something like a paper clip or toothpick, prick that small hole marked reset for a while, and you're good to go.