The newly bought apple fell into the water, there is a way to help, and there is no way to ask for c

Hello friends, it's an old problem about water ingress on mobile phones. Here's how.

1.Water ingress and crashing are the two major taboos in the use of mobile phones, and water ingress of mobile phones is particularly serious. According to an engineer from Guoxin, after the mobile phone gets into the water, the first thing to do is to turn off the power, of course, not to press the shutdown button, but to remove the battery.

Because as soon as you press the shutdown button, the mobile phone will be powered on, and it is likely that a short circuit will occur, causing damage to the mobile phone, and then send it for repair as soon as possible. If your phone's warranty has expired and you don't want to send it for repair, you can boldly take it apart! Wipe the parts of the phone with a tissue, and then blow it with a hair dryer for a few minutes, in order to ensure that all the internal parts are dry, it is advisable to air dry the phone for a few more days before you can turn it on again.

Once the mobile phone gets into the water, the battery should be removed immediately, and it must not be turned on immediately to understand the condition of the mobile phone. After removing the battery, do not use a hair dryer to deal with it, and immediately send it to the repair professional to disassemble the machine for water treatment, such as falling into sewage or corrosive liquid, and use ultrasonic cleaning and drying before proceeding to the next step of maintenance. If the mobile phone can still be used after water penetration, it should be sent to a professional to deal with it to avoid corrosion of the circuit board and make it impossible to repair.

No matter what kind of water the phone falls into, you should first remove the phone battery and no longer power the phone. If it falls into clean water, remove the battery and clean the phone with anhydrous alcohol, because the alcohol volatilizes quickly, and the water on the circuit board can be volatilized together. Then use a heat gun or hair dryer to dry the circuit board, and then power up the test machine, and most mobile phones will work normally.

If it falls into the sewage, it should be cleaned immediately, and the dirt that can be seen should be cleaned first. Use a brush to brush off the impurities attached to the pins of the components. Then, the circuit board is scrubbed with an alcohol cotton ball, and if the pollution is serious, the impurities must be vibrated out with the help of an ultrasonic washing instrument.

Then use an air gun to dry the circuit board, and then repair all the chips.

4.If it doesn't work, send it to the after-sales service for maintenance, this is not expensive!

If your phone falls into the water, you must not blow it with a hair dryer, because you will blow the water into the small parts inside, which will be difficult to remove.

You can try to put your phone in a sealed bag, put it in a rice bowl at home (just take the rice and bury it), and you can use it in a day or two.

Falling into the water is not warranted, and electronic products into the water remember not to blow with a hair dryer, wrapped in a plastic bag and put in the rice bowl is the right solution, after two days.

If it doesn't affect the use, there is no need to fix it, put it in a ventilated place or take a hair dryer to blow it for a while.

Wrap it in a plastic bag and put it in a rice bowl.

What are you afraid of when you buy a new one with a warranty.

Since there is no short circuit in the circuit, it can be used normally after drying.

1. First of all, of course, the whole machine is disassembled, and the corresponding screwdriver should be prepared before that.

2. When removing the screen, pay attention to gently separating the chiplet connected to the motherboard from the motherboard.

3. Before removing the metal shielding isolation layer, tear off the network access card and the card slot sticker under the network access card.

4. The last is to take a hair dryer to dry blow, but don't blow on the screen for a long time, such a high temperature will destroy the screen, even if the screen has a watermark, you can use the phone normally, the water in the screen will generally dry in two days, and you will see that the watermark inside is getting smaller and smaller.

5. Blow the front and back of the motherboard to ensure that there is no moisture residue, and try to blow out the water at the earpiece and buttons.

6. Finally, put the disassembled mobile phone in a dry and noisy place, preferably about two days, and then install it.

Step 1: Salvage.

Whether the mobile phone is dropped in the basin, the toilet, the lake or the river, or in the rain, the first step is not to be in a daze, and let the water machine get out of the water source as soon as possible. Because the longer the time in the water, the greater the damage to the mobile phone, such as the motherboard, screen, battery, buttons, etc., just like a person drowning, the sooner you are rescued, the greater the probability of survival.

Step 2 Wipe dry.

After scooping it out of the water, immediately wipe the surface of the phone dry with a dry paper towel, rag or even clothes, take out the SIM card slot, and use a paper towel to absorb water at each opening of the phone. Remember, don't press buttons such as the power button and volume button, don't turn on, don't turn on, don't turn on, this is the most important point, because once turned on, due to the water in the body, connecting the power again will cause the motherboard to burn out.

Step 3 Drying.

Use a hair dryer to turn on hot and cold air alternately, aiming at each opening of the mobile phone, such as the charging port, headphone jack, SIM card slot, etc., if it is soaked in water, you need to blow for a while, if it is only partially watered or partially watered, you do not need to blow for too long. The phone can then be placed in a pile of rice or desiccant and taken out after a few hours.

Step 4 Try to turn it on.

After the above steps, you can try to boot up, if it can turn on normally, don't be happy too soon. Check whether the buttons, fingerprint recognition, screen touch, mobile phone speakers, etc. of the mobile phone are normal, if the use is normal, then you will be happy in vain, because you can't change the new phone;If it doesn't turn on or some of the functions fail, then, congratulations, you still have the opportunity to change to a new phone, and enter the five steps.

Hurry up and scoop it up, shake it first, let it dry with a paper towel, turn it off directly, and enlarge the moisture absorption in the rice.

1.Do not try to turn on the device immediately if there is water ingress. Because the iPhone has a built-in battery that cannot be removed, the motherboard will be short-circuited if it gets into the water, and if it is turned on, the motherboard will be burned, causing irreparable consequences.

2.If there is water, do not try to charge it immediately, because the iphone has a built-in battery that cannot be removed, and the motherboard will be short-circuited if it is flooded, and if it is charged, the motherboard will be burned, causing irreparable consequences.

3.You can first use toilet paper to dry the water outside the mobile phone, and then place the mobile phone screen horizontally to prevent water from flowing to the motherboard, and then use a blow dryer to dry the water, and turn on the temperature at medium or small temperatures.

4.Wipe down the circuit board with anhydrous alcohol and try to turn it on. Because alcohol volatilizes quickly, the moisture on the circuit board can be volatilized clean.

If the problem does not solve your problem, it is recommended that you bring your phone to an Apple customer service center for repair.

Take it out to dry, and if you don't have a warranty, take it apart and blow it with a hair dryer. During the warranty period, I think it's better to disassemble it, and this is the only way! Because Apple phones are not waterproof, if you turn on the phone rashly, it is easy to burn out

In the sun, the electric wind blows. If it doesn't work, take it and fix it.

Don't try the following wrong methods after your phone gets into water.

1.Don't shake your phone too hard. Because under the constant shaking, the liquid will swim inside the machine, and the moisture may enter deeper and burn the internal chip of the machine.

2.Don't use the hot air of a hair dryer to dry your phone for a long time. iPhones are now all metal bodies, and metal conducts heat easily, which will blow off the solder joints of the motherboard inside the machine, causing the motherboard to malfunction.

3.Do not attempt to charge a phone that has been flooded. An iPhone that gets into the water may have water stains inside, which can burn out the motherboard when it is powered on and cause a more serious failure.

It is recommended to send the mobile phone to a regular repair center for testing to avoid unnecessary damage to the mobile phone.

What to do if the iPhone gets into the water:

Do not try to turn on the machine immediately after water ingress. Once you try to boot it, it will increase the area burned out by the motherboard by short circuit.

2.Don't shake your iPhone. If you shake your iPhone, water will flow and water may expand inside your iPhone.

3.Clean up the water ingress location in order (Apple Customer Service Center 010 5363 0616) Quickly remove the SIM card and wipe the water in the iPhone shell, Dock port, and SIM card slot.

4.Do not turn on the machine immediately after absorbing or wiping off the water. It is essential for a professional to clean the moisture of each chip of the internal motherboard.

5.Water ingress can't be turned on, most of them are short-circuited motherboard power supplies, CPUs, hard disks and other chips. The motherboard needs to be repaired.

6.Contact a repair center for free testing and repair.

If your phone accidentally falls into the water, it is recommended to deal with it immediately as follows:

1. First of all, the phone should be salvaged as soon as possible, and it is best to remove the SIM card at the same time to avoid losing contact information. The longer it stays in liquids, the more damage your phone will suffer for life.

2. If the phone falls into salt water, not fresh water. Salt water forms a "salt crust" in the phone's internals. If your phone has fallen into seawater or other salty water, you need to gently rinse it with fresh water – after removing the SIM card and before the drying process begins.

3. Wipe every part of the phone with a cloth or paper towel, and don't move or shake the phone too much to avoid water swimming everywhere inside the phone.

4. Try wrapping your phone in a cloth or paper towel for a few minutes to absorb too much moisture. Turn on the cool air setting of the hair dryer and blow at the hole of the mobile phone about 30cm away from the mobile phone for at least one hour.

5. Finally, wrap the phone in a thin tissue and put it in a jar or bag full of rice for at least 24 hours, during which time it cannot be turned on. Rice absorbs water very well and can save a damp phone.

6. The above is only a salvage measure, if there is still a fault after taking it out of the rice, please go to the after-sales service.

iPhone is a waterproof phone. If the iPhone falls into the water, take the phone out of the water immediately and turn it off, clean the surface of the phone and the earpiece charging port in time, check the phone after standing and deal with it first

1. If everything is used normally, just continue to use it.

2. If it is a small problem such as the battery, you can find a third party to repair it.

3. If some key parts are damaged, they must be officially repaired.

The specific treatment method of the mobile phone falling into the water:

1. Reducing the contact time between the mobile phone and water will minimize the damage of the mobile phone.

2. The longer the mobile phone is immersed in water, the greater the damage to the earpiece, microphone, screen and motherboard of the mobile phone. Remove your phone from the water, quickly dry it to indicate water trails, and remember not to try to turn it on.

3. After taking out the mobile phone, quickly take out the battery, most of the mobile phones are integrated, and the battery needs to be handed over to professionals for insight operation. If you feel that the water in the phone is almost shaken off, don't try to turn it on, use a hair dryer to keep the temperature of your hands not hot and blow on the hole in the phone, three minutes each time, blow three times, and then start to dry.

If the iPhone falls into the water and is quickly fished out, it will be fine. Taking iPhone13 as an example, Apple13 uses IP68 waterproof, and falling into the water will not cause internal water ingress.

If the mobile phone has replaced the screen or battery, the original waterproof performance must have been lost, so the possibility of water ingress is not ruled out, if it is the original unrepaired machine hanging in the water is no problem, just wipe the surface of the water stains dry.

How to deal with mobile phones falling into the water.

1. Fish out your phone. After the mobile phone falls into the water, it is necessary to fish the mobile phone out of the water in a short time, and the longer the mobile phone is soaked in the water.

For a long time, the larger the water inlet area of the mobile phone, the greater the damage to the phone's earpiece, buttons, screen and motherboard.

2. Dry your phone. After taking out the phone, wipe the surface of the water clean, and do not turn it on at this time, because the water is likely to have penetrated.

Once it is not cleaned up, it will cause the motherboard to burn if it is powered on again.

3. Blow dry your phone. Take out the hair dryer and blow slowly on the place where the water enters the phone, keeping the cold air as much as possible, and the temperature of the blowing is not high.

Too high, as the heat of the hair dryer is likely to cause devastating damage to the sensitive components inside the phone.

Apple will not turn on if thrown into the water, or it will fall into an infinite restart, and there will also be some hardware failures.

Power and boot issues: There is a high chance that we will not turn on, or get stuck in an infinite reboot, and there will also be some hardware failures, such as speakers and handsets, microphone failures. We may also receive some fault alerts, such as messages such as no support for charging, or hardware or application failures.

In fact, every new series of iPhones comes with a liquid contact indicator. The Liquid Contact Indicator (LCI) checks if your iOS data is at risk. If you see a red dot appear, it means that your device has been exposed to water.

If there is a red dot on the unbroken grip, your device is working fine.

Precautions after iPhone falls into the water

1. Remove the phone from the water as soon as possible, and immediately remove the battery and SIM card to prevent short circuit and loss of contacts.

2. If the iPhone falls into drinkable fresh water, the problem is not very big, if it is salt water such as seawater, once it forms a "salt crust" in the internal components of the mobile phone, it will be very troublesome to clean up, if you are an unfortunate member, then you can use fresh water to rinse the phone, of course, after removing the battery and SIM card.

3. Wipe the inside of the phone with a clean cloth or paper towel, do not move and shake the phone too much, and avoid water scurrying inside the phone.

4. Wrap your iPhone with a clean cloth or paper towel to create a small vacuum effect and suck out excess moisture, preferably in a place where the heating is circulating.

5. The water-filled iphone can be put into the rice tank for 24 hours, the rice has good water absorption, which can save the damp mobile phone, of course, it needs to be turned off and put in.

6. Try to turn on the phone after 24 hours of entering the water, if the battery cannot be charged, then you must change the battery.

7. There is a small white dot near the battery compartment, if it has turned red, then the maintenance personnel know that this is not a quality problem of the equipment, and all the next maintenance or repair will have to pay for it.