Unable to connect route 25, unable to connect route

Not necessarily, or it could be, you set the NIC to automatically acquire the IP and start running.

Enter cmd enter.

Enter ipconfig all

You'll know what the IP is.

Uninstall the network card in Device Manager and restart the computer. Let the system automatically install the NIC and then set the IPOther than that.

I haven't used this method, it's a reference on the Internet, you can try it)

Start --run --cmd--type.

netsh int ip reset

First of all, you need to make sure that one of them can enter the router. If not, you can reset the route and try again. Here's how:

Unplug the network cable and power supply connected to the router first, then press and hold the reset button with a slightly pointed object, preferably with a ballpoint pen, and then power on for a few seconds and see the M1 M2 light on the router flash several times at the same time, and then let go when it flashes normally. The route reset is complete.

If just one machine can't connect to the route, then you can see if the IP address of your local connection is set incorrectly. You can disable local connections. Then set the IP to the subnet mask between the default gateway DNS standby and then enable the local connection.

Try again!!

<>1. Router connection problems, ordinary wireless routers generally have 5 network cable interfaces, 1 WAN port, and 4 LAN ports. When many users connect to the router, they connect these interfaces incorrectly, resulting in the router not being able to connect to the Internet.

2. Correct connection method: plug the network cable from the cat optical modem into the WAN port of the router; If you don't use a cat for your home broadband, you need to plug the broadband network cable into the WAN port of the router. If you have a computer at home, connect it to any of the router's LAN ports (1 2 3 4) with an Internet cable.

3. Pointing to the router problem: Sometimes, it is some problems with the router itself, which causes the Internet to be connected after setting. In this case, it is recommended to factory reset the router and then set it up again.

The method of factory resetting the router is also very simple, press and hold the reset button on the router for about 10 seconds, and you can restore this router to factory settings.

Usually, there is a problem with the connection and settings of the router's network cable.

1. The bus of the broadband network is connected to the WAN port of the router, and the LAN port of the router is connected to the computer.

2. After starting the device, open the browser and enter it in the address bar to enter the wireless router settings interface. (If you can't get in, please look at the nameplate at the bottom of the router or the router instruction manual, the default settings of different models of routers are different.) ）

3. An account and password to log in to the router appear in the settings interface, enter the default account and password admin, or refer to the manual;

4. After successful login, select the interface of the setup wizard, which will automatically pop up by default;

5. After selecting the setup wizard, a window will pop up to explain that you can set the basic parameters of the router through the wizard, and click Next directly;

6. Set up step by step according to the setup wizard, select the Internet mode, usually ADSL users choose the first PPPoE, if you use other network service providers, select the following two according to the actual situation, if you don't know how to choose, directly select the first item to automatically select, convenient for novice operations, click next after selection;

7. Enter the account and password applied for from the network service provider, and go directly to the next step after the input is completed;

8. Set the wifi password, try to make the alphanumeric combination more complicated, and it is not easy to be rubbed off the network.

9. After entering correctly, it will prompt whether to restart the router, select Yes to confirm the restart of the router, and you can access the Internet normally after restarting the router.

The possibility of bad is there.

You change the port of the router first, it may be that port is broken.

If it doesn't work, it may be that the router settings are changed due to a vicious attack, and you can go to the route to check whether this problem occurs.

There is also a possibility that your router is of poor quality and overheated, causing the route to crash.

If so, turn off the router and stop it for a few minutes before you try again.

If none of the above works, then change routers.

Sometimes the network at home suddenly can't be connected, and you can still access the Internet when you used to go online, what's going on? For netizens who don't know, let's follow the footsteps to find out what happens if the router is connected to the Internet. 1First of all, check the working status of the optical modem at home to see if the indicator light on the optical modem is normal.

There is no red light. 2. When the modem is normal, let's take a look at the wireless router to see if the network cable connected to the modem and the wireless router is loose. Then restart the router, the easiest way to restart is to unplug the power cord, wait for 3-5 seconds and plug it in, wait for half a minute for the router to work normally, and try to see if it can surf the Internet.

3 Usually restarting can solve most problems, if you are still not connected to the Internet. You need to reset the router, open a web browser on the computer connected to the network cable at your home, type, open the settings router settings, enter the administrator name and password, and then look for the setup wizard inside, reset the network, after the settings are completed, you need to click the "Restart router" option, so that the wireless router will be updated to the new settings. 4. Because of the different manufacturers of routers, the default management address and the default username and password may be different, and the stickers on most routers will indicate the address and default user name to enter the management interface.

The above is an introduction to what happens when the router is connected to the Internet, do netizens understand?

Hello everyone, I am Time Fortune Network Intelligent Customer Service Time Jun, and the above questions will be answered by me. The router works normally but the computer cannot connect to the network for the following reasons: 1. The wifi itself is a problem, and the wifi may not be connected normally, resulting in the inability to access the Internet; 2. Router problems, the router may be overheated or damaged; 3. There may be broadband arrears, resulting in inability to access the Internet; 4. The wifi name contains Chinese, resulting in some computers unable to connect to the Internet; 5. Computer system problems, there may be problems with the system, resulting in connecting to wifi but unable to access the Internet.

Suggested solutions: 1. Use other mobile phones or devices to connect to wifi to try whether you can access the Internet and rule out the problem of wifi itself; 2. Restart the router to try, or restore the router to factory settings, then dial up the Internet again, and reset the wifi according to the setup wizard, or change to a new router and dial up to connect to the Internet; 3. Contact the broadband customer service to confirm whether the broadband is abnormal, such as arrears, recharge the broadband, and then dial up the connection; 4. If the wifi name contains Chinese, it is recommended to modify it to English or a combination of English and numbers before connecting; 5. If the above reasons are ruled out, then it is likely to be a computer system problem, and it is recommended to restore the factory settings. See if that solves the problem.

The router is working properly but the computer cannot connect to the network for the following reasons:

1. The wifi itself is a problem, the wifi may not be connected normally, resulting in the inability to access the Internet;

2. Router problems, the router may be overheated or damaged;

3. There may be broadband arrears, resulting in inability to access the Internet;

4. The wifi name contains Chinese, resulting in some computers unable to connect to the Internet;

5. Computer system problems, there may be problems with the system, resulting in connecting to wifi but unable to access the Internet.

Suggested workaround:

1. Use other mobile phones or devices to connect to wifi to try whether you can access the Internet and rule out the problem of wifi itself;

2. Restart the router to try, or restore the router to factory settings, then dial up the Internet again, and reset the wifi according to the setup wizard, or change to a new router and dial up to connect to the Internet;

3. Contact the broadband customer service to confirm whether the broadband is abnormal, such as arrears, recharge the broadband, and then dial up the connection;

4. If the wifi name contains Chinese, it is recommended to modify it to English or a combination of English and numbers before connecting;

5. If the above reasons are ruled out, then it is likely to be a computer system problem, and it is recommended to restore the factory settings. See if that solves the problem.

If the wired network is normal, the network from the router to the operator is normal, and the fault is due to the wireless part of the LAN, including the wireless module of the router and the wireless module of the Internet access device.

Take a commonly used notebook as an example to illustrate the cause of the failure and how to deal with it

1. Find a mobile phone to connect to wifi first, see if the mobile phone Internet is normal, if the mobile phone Internet is normal, it means that the router wireless signal is normal, the fault is in the notebook, uninstall the notebook wireless network card and then reinstall it, it can be solved.

2. If the mobile phone is also limited to obtain the address like the notebook and cannot be connected, it means that there is a problem with the wireless part of the router.

3. There is also a possibility that the signal between the router and the laptop is blocked, resulting in a weak signal, so that the wireless channel cannot be established, and the laptop can be moved to the vicinity of the wireless router, which can solve the problem of unable to connect caused by signal shielding.